Zeiss LSM 710 Bedienungsanleitung

Zeiss LSM 710

1

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

Startup

1. Turn on the Main Switch (see image below, #1).

2. Turn on the Systems/PC and Components Switches (see image below, #2).

3. Power up the X-Cite short arc lamp (see image below, #3).

Note: the lamp should not be turned on/off in quick succession. Always wait ca. 20 min.

4. Turn the key of the Argon laser power supply 90° (clockwise) from position 0 to 1 (see below, #4).

5. Turn on the PC (no image shown).

6. After about 5 min, switch the Lasos Argon laser control unit from 'idle' to 'run' (see image below,

#6). Wait until the green and/or red LED on the Lasos control unit lights up. If the red LED shows

up, turn the control knob counterclockwise until only the green LED is on.

Note: if you use only 488 nm at low power, you may leave it in 'idle' mode all the time.

7. Start the software: double-click on the ZEN icon. In the Login dialog, select 'Start System'. Once

ZEN is loaded, select the 'View' menu and check 'Show all (global)'.

Zeiss LSM 710

2

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

Shutdown

1. Switch the Argon laser from 'run' to 'idle' (see image below, #1).

2. Turn the key on the Argon laser power supply 90° counterclockwise from position 1 to 0 (see

image below, #2).

3. Close ZEN. In the laser tool window popping up, turn off all lasers (see image below, #3). Turn off

the computer.

4. Turn off the X-Cite lamp (see image below, #4).

5. Push the 'Load position' button on the touch panel (on the microscope table) to lower the

objective (see below, #5). Remove the sample and clean oil objectives with lens cleaning paper.

6. Wait until the fan of the Argon laser has stopped. Then turn off the Systems/PC, Components and

Main Switches (see below, #6).

7. Put the dust cover on the microscope.

Leaving the system for the next user

1. Switch the Argon laser to 'idle' mode (see image above, #1).

2. Push the 'Load position' button on the touch panel (see image above, #5). Remove the sample

and clean oil objectives with lens cleaning paper.

3. In ZEN, close your images. If you have used the 561 and/or 633 nm laser, leave them running.

Leave ZEN running.

4. Disconnect from servers:

HIVE: click on the HIVE icon. In the dialog popping up, select 'Disconnect'

VBC share: click on the 'Logout' icon

Zeiss LSM 710

3

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

Troubleshooting

ZEN hangs during startup

1. In the login screen, click on the triangle left to 'Boot Status' (see the image below, #1).

2. Check the messages in the expanding scroll pane (see the image below, #2).

3. If there's a message "No connection to realtime controller", open the the door of the RTC

(black box left to the microscope) , press the Reset Button (see image below, #3) and wait

until ZEN resumes.

Zeiss LSM 710

4

LSM 710 –Quick Guide MFPL BioOptics - Light Microscopy

No excitation light while scanning

1. Check if the Argon laser is turned on (key in position 1, see step #4 in the 'Startup' chapter).

2. On the Main Power unit, check if the Laser key is in ON position (horizontal, see image below).

3. Check if the transmitted light column is in upright position (which activates a magnetic sensor

beneath the column). If seated properly, a LED on the scan head should burn while scanning. If

not, pull the transmitted light column to a fully upright position (see image below).

4. Check the Argon laser power supply for two red LEDs (POWER and INTERLOCK). If the

INTERLOCK LED is off, exit ZEN, power off the power supply and turn it on again (ON/OFF

switch beneath the thick cable. Do NOT use the Mains or Component Switches).

5. Contact the facility if the problem persists.

Andere Handbücher für LSM 710

6

Inhaltsverzeichnis

Andere Zeiss Mikroskop Handbücher

Zeiss

Zeiss SL 800 Bedienerhandbuch

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss LSM 510 Inverted Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungs- und Wartungshandbuch

Zeiss

Zeiss Axiovert 200 Bedienungsanleitung

Zeiss

Zeiss 880 Installationsanleitung

Zeiss

Zeiss Axioskop 2 FS plus Bedienungsanleitung

Zeiss

Zeiss Axioscope 7 Bedienungsanleitung

Zeiss

Zeiss Axioplan Universal microscope Bedienungsanleitung

Zeiss

Zeiss AxioExaminer FTP-2100 Bedienungsanleitung

Zeiss

Zeiss LSM 710 SIM Bedienungsanleitung

Zeiss

Zeiss Axiovert 200 Bedienungsanleitung

Zeiss

Zeiss HBO 100 Bedienungsanleitung

Zeiss

Zeiss EVO Bedienungsanleitung

Zeiss

Zeiss LSM 510 Inverted Bedienungsanleitung

Zeiss

Zeiss Definite Focus.2 Bedienungsanleitung

Zeiss

Zeiss Axio Observer Series Bedienungsanleitung

Zeiss

Zeiss OPMI 1FR XY Bedienungsanleitung

Zeiss

Zeiss Axioplan 2 imaging and Axiophot 2 Bedienungsanleitung

Zeiss

Zeiss Stemi 305 cam Bedienungsanleitung

Zeiss

Zeiss LSM 900 Bedienungsanleitung

Zeiss

Zeiss Axiolab Pol Bedienungsanleitung

Zeiss

Zeiss Axio Examiner Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung