CrimeStopper CS-2100 Handbuch

CS-2100

REMOTE CONTROL ALARM SYSTEM

INSTALLATION & OPERATING INSTRUCTIONS

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Siren, L.E.D.,

Power, Ground, Doorpin, etc.

-OPTIONAL: These are features to be connected only if desired or agreed upon by the installing dealer (i.e. Door

Locks, Starter Kill, Hood, Trunk, and Auxiliary Remote Output etc.) Optional features may require extra parts and/or

labor to install.

TECH SUPPORT

Mon-Fri 8:00 AM-4:30 PM Pacific Time

(800) 998-6880

www.crimestopper.com

[email protected]

INSTALLATION CAUTIONS & WARNINGS

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR BAGS,

ABS BRAKES, AND BATTERY).

TO PREVENT A POSSIBLE DEAD BATTERY remove vehicle dome light fuse while working on the vehicle. MAKE

CERTAIN TO REINSTALL FUSE PRIOR TO TESTING FOR DOOR TRIGGERS.

DO NOT EXCEED MAXIMUM OUTPUT RATINGS! -SERIOUS DAMAGE MAY OCCUR. LIMITS FOR ALARM

FUNCTIONS ARE LISTED WHERE APPLICABLE. IF UNSURE ABOUT CURRENT LOAD, MEASURE LOAD WITH

AN AMP-METER.

REMOVE MAIN SYSTEM FUSE(S) before jump starting the vehicle or charging the battery at high boost.

This device complies with FCC Rules part 15. Operation is subject to the following

two conditions: 1) This device may not cause interference, and (2) this device

must accept any interference that may be received, including interference that may

cause undesired operation. The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modification to this equipment. Such

modification could void the user's authority to operate the equipment.

COMPONENT MOUNTING

DO NOT mount the control unit in the engine compartment. DO NOT Mount the control unit or wiring harness

where they can become entangled with moving parts such as brake/gas/clutch pedals, or the steering column.

The alarm control module should be mounted in a concealed location. The antenna wire should be routed

away from any metal if possible. DO NOT alter the length of the antenna wire, route it with other wires, or

groundit.

SIREN MOUNTING: Mount the siren under the hood to fender-well or other body surface with the open end facing

downward. Run the red siren wire through the firewall using a rubber grommet. Ground the black wire to the body

metal near the siren.

LED: Mount the red LED in a visible location on the dashboard or console.

Shock Sensor: Mount the included shock sensor with wire ties to an under dash wire harness or fasten with screws to

firewall or side paneling.

Override/Program Button: Mount the Override/Program push-button in a hidden, but accessible location to the user

in case the system must be disarmed without the use of the transmitter. This switch is also used to program certain

features.

WIRING

GRAY WIRE: (-) AUX REMOTE OUTPUT 1 (Optional, May Require Relay)

Connects to terminal 85 of a relay. Connect terminal 86 to constant. Connect terminal 87 to +12V constant or ground

depending on the type of circuit that needs to be activated. Connect terminal 30 to the device/circuit to be activated.

BLACK/WHITE WIRE: (-) DOME LIGHT ILLUMINATION (Optional, May Require Relay)

Connect to terminal 85 of relay. Connect terminal 86 to constant. Connect terminal 87 to +12V constant or ground

depending on the type of dome light circuit in the vehicle. 30 to the dome light circuit.

ORANGE WIRE: (-) NEG. ARMED OUTPUT / STARTER DISABLE (300mA Negative)

Ground output when system is armed. This output is used for disabling the starter or to activate other devices such as

scanner LED’s, window modules, voice modules etc. For starter kill, cut starter wire and connect between 87A and 30

on relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in the ON and CRANKING

position.

BLUE/WHITE WIRE: (-) NEG. DOOR LOCK OUTPUT

Connects to lock circuit of NEGATIVE door lock systems or to terminal 85 of a relay. See Door Lock diagrams PG 7.

WHITE/RED WIRE: (-) NEG. DOOR UNLOCK OUTPUT

Connects to unlock circuit of NEGATIVE door lock systems or to terminal 85 of a relay. See Door Lock diagrams. PG 7

WIRING

VIOLET WIRE: (+) DOOR TRIGGER INPUT

Same as GREEN wire [below] except this wire is used for vehicles that show a positive voltage (12 volts) when the

door is open such as many Ford, Lincoln, Mercury vehicles.

BLUE WIRE: (-) HOOD/TRUNK INPUT

This wire is an input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches

that read ground when open. If no existing switches are available, install new pin switches. Note: DO NOT mount new

pin switches in water pathways.

GREEN WIRE: (-) DOOR TRIGGER INPUT

Identify the wire that reads Ground when any door is open and 12 volts when all doors are closed.

YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS

Connect to an ignition wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and “Start”

positions.

BROWN/WHITE WIRE: (-) HORN HONK OUTPUT (Optional, May Require Relay)

This wire provides a pulsed (-) negative output for honking the vehicle’s horn when the system is tripped or when panic

is activated. Connect this wire to Negative Horn trigger wire in the steering column or to a relay on vehicles with a

positive horn circuit.

WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT (15 Amp Fuse)

Connect to switched parking light wire at back of light switch. If this is not possible, connect directly to one of the

parking lights at the front of the vehicle. European vehicles require separate right and left circuits. Use a dual relay or

2 diodes to separate the output signal.

BROWN WIRE: (+) SIREN OUTPUT (3 Amp Max.)

Connect to RED siren wire.

RED WIRE: +12V POWER INPUT (15 Amp Fuse)

Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the vehicle

battery positive terminal.

BLACK WIRE: SYSTEM CHASSIS GROUND

THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt from

the connection point to ensure a good connection. We recommend the kick panel area for your ground point.

2 PIN PLUG (WHITE): PROGRAM/OVERRIDE PUSH BUTTON

2 PIN PLUG (RED): LED INDICATOR (RED FLASHING LIGHT)

WIRING / PROGRAMMING

4 PIN SENSOR PLUG:

WHITE WIRE: NEG. WARN AWAY *The Sensor supplied with the system does not require

BLUE WIRE: NEG. TRIGGER any additional wiring, simply mount the sensor in a

BLACK WIRE: SENSOR GROUND suitable location, plug in, and adjust sensitivity.

RED WIRE: SENSOR +12V POWER

SILENT ARMING /DISARMING

The system can be silently armed and disarmed as normal with but with no siren chirp. Turn ignition on and press the

#2 Button for about (3) seconds. You will hear (2) siren chirps. After the ignition is turned off, there will be no siren

chirps on arm/disarm. Repeat this procedure to enable chirps. (There will be 4 chirps when re-enabling)

ACTIVE RE-ARM PROGRAMMING

To enable this feature, Turn ignition on and press the #1 Button on the for about (3) seconds. (2) Siren chirps will be

heard when disabling this feature. Repeat procedure to enable. (1 siren chirp when enabling)

TRANSMITTER PROGRAMMING Note: System can learn up to 3 different codes max.

1. Turn Ignition ON and OFF 3 times quickly, leaving it ON the 3rd time. (ON/OFF, ON/OFF, ON) You should hear (1)

short chirp.

2. Push the Program/Override Button for 5 seconds until the siren chirps (3) times. Release the button.

The system is now in programming mode.

3. Press Button #1 on new transmitter –siren will chirp to confirm programming. Repeat Step 3 within 5 sec. for up to

2 additional transmitters.

4. Turn off Ignition.

OPTION PROGRAMMING

PROGRAMMABLE OPTIONS

1. Turn the Ignition ON, wait 1 second and press the Override/Program button 5 times. You should hear a long

confirmation chirp.

2. Within the next few seconds, press the Override/Program button [again] the number of times that corresponds to

the feature list below. The siren will chirp for each button press.

3. When you get to the desired option number, press button the appropriate button on the transmitter change the

option according to the chart below. Button #1 gives a single light flash/siren chirp and Button #2 gives two light

flashes/siren chirps. See chart Below for Option descriptions and vales.

4. Change ONE option at a time repeating steps 1-3 as needed. When you are finished customizing options, check

operation to see if the option(s) have changed. **SEE CHART ON NEXT PAGE**

BUTTON #1

BUTTON #2

OPTION CHART

* = DEFAULT

Option # Option Description Selection Button 1 Button 2

1Passive Arming ON or OFF OFF* ON

2Autolock with Ignition ON or OFF ON* OFF

3Double Unlock Pulse 1 or 2 pulses 1 Pulse* 2 Pulses

4Dome Light Timer 10 or 60 sec. 10 sec.* 60 sec.

5Door lock pulse 1 or 3 sec. 1 sec.* 3 sec.

6Carjack Active or Passive Active* Passive

7Lock when Passive Arming ON or OFF OFF* ON

8Restore Options to default Button 1 Press Btn. #1

OPERATION

ACTIVE ARMING

To arm the system, press the #1 button on the transmitter. You will hear a single

siren chirp and the lights will flash once. Doors will lock and the starter will be

disabled if these optional features are installed. The red LED in the vehicle will

start flashing after 15 seconds. After a short delay to allow vehicle and electronics

to stabilize the system will be completely armed. If there is an intrusion into the

vehicle or hard impact to the body the alarm will sound and flash the lights for 45

seconds. After 45 seconds the system will automatically shut off and re-arm to

continue to protect the vehicle. If a door is left open the unit will cycle a second

time and continue to protect the other non-tampered zones. Note: To

Arm/Disarm with a Soft (NIGHT) chirp press and release the #2 (Small)

button quickly.

DISARMING

To disarm the alarm and unlock the doors, press the #1 button on the transmitter. You will hear 2 siren chirps and the

lights will flash twice. Dash LED stops flashing.

REMOTE PANIC PROTECTION

To sound the alarm upon command, press and hold the #1 Button for at least (2) seconds until the siren sounds.

Press the same button again to reset panic mode.

TRUNK/HATCH POP (REMOTE AUX. OUTPUT 1, OPTIONAL)

To pop the trunk (if optional feature is installed), press the #2 Button for at least 1 second.

OPERATION

EMERGENCY OVERRIDE/ VALET MODE

If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to perform an

Emergency Disarm. Open the door with the key, which will activate the alarm, turn the ignition ON, and press the

override/program button about 3-4 seconds. The Alarm will disarm and go into Valet mode. (LED on solid). Repeat

the above procedure to Exit/Enter Valet mode. NOTE: Keyless Entry features will still operate when in Valet Mode.

ACTIVE CARJACK PROTECTION (Programmable Option #6)

This feature provides Active (user controlled) Carjack protection. When the Ignition is on (vehicle is running), press

buttons #1 and #2 together for 1 second to activate a Carjack countdown. (Parking lights will turn on for 3 seconds as

confirmation) 30 seconds later, the unit will begin a Carjack Cycle consisting of 15 sec. of pre-warning chirps turning

into a full activation with siren/flashing lights for up to 5 min. To reset Carjack, press Buttons #1 and #2 together or

turn Ignition OFF, then ON and hold the override/program button for 3 seconds.

PASSIVE CARJACK PROTECTION (Programmable Option #6)

This feature provides Passive (involuntary) Carjack protection. When the Ignition is on (vehicle is running), a Carjack

countdown will be activated when a door is opened. See above for Carjack cycle description.

PASSIVE ARMING / PASSIVE LOCK MODES (Programmable Options #1, 7)

Passive (Automatic) Arming will occur 30 Seconds after the ignition is turned off and the last door has been closed.

The LED will begin flashing rapidly while counting down. If a door is open, the system will wait (LED solid) for the door

or zone to close before arming. If Passive locks are programmed ON, then unit will also lock the doors when arming.

PRIOR INTRUSION ALERT

If the system was tripped in your absence, the dash LED will be flashing rapidly and when the system is disarmed it will

chirp/flash 3 times. Inspect your vehicle to check for any damage or if a theft has occurred.

DOME LIGHT ILLUMINATION (Optional, Programmable)

This feature turns on the vehicle’s dome light upon disarm for 10 (or 60) seconds or until the key is turned on.

OPEN ZONE ALERT/BYPASS

If a door/zone is left open after arming, the siren will warn you with 4 chirp/flashes and bypass the zone automatically.

AUTOLOCK/UNLOCK WITH IGNITION (Programmable)

This feature will allow the unit to automatically lock when the ignition is turned on and unlock when turned off.

ACTIVE RE-ARMING (Programmable)

Allows the system to re-arm itself 30 seconds after being disarmed with the remote if a door has NOT yet been

opened. This is handy if the vehicle is accidentally disarmed without your knowledge.

POWER DOOR LOCK WIRING

87A

BATTERY

IGN

PROG/

VALET BTN

PIN SWITCH

(+)POSITIVE DOOR

HOOD/TRUNK

(-)NEGATIVE

RELAY

PIN SWITCH

OPTIONAL

STARTERKILL

LED

FUSE

BOX

IGNITION

"ON & START"

START WIRE

(-) DOOR TRIGGER

YELLOW

CUT

(-) AUX. REMOTE OUTPUT

GRAY

(-)HOOD/TRUNKTRIGGER

BLUE

WHITE/RED

NEG. ARMED OUTPUT

ORANGE

(STARTER DISABLE)

STARTER

(+) POS. IGN SWITCHED "ON"

CHASSIS GROUND

RED

FUSE

10A

BROWN

+ 15 AMP MAX

WHITE

BLACK(GROUND)

WHITE(WARNING)

RED (+)

BLUE (TRIGGER)

PARKING

LIGHTS

(-) NEG. LOCK OUTPUT

DUAL-STAGE

SHOCK SENSOR

SIREN

BLUE/WHITE

(-) NEG. UNLOCK OUTPUT

87A

BLACK/WHITE

(-)DOMEILLUMINATION

BLACK

VIOLET

GREEN

RELAYS

OPTIONAL

BROWN/WHITE

(-) NEG. HORN HONK

CS-2100

+ SIREN OUTPUT

RED

(+) DOOR TRIGGER

DOOR

(-) NEGATIVE

PIN SWITCH

(+) 12V POWER INPUT

WHITE

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper Fortress FS-30 Bedienungsanleitung

CrimeStopper

CrimeStopper Rage CS-2009 Bedienungsanleitung

CrimeStopper

CrimeStopper SP-202 Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4008 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2002DPII Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9600 Technisches Datenblatt

CrimeStopper

CrimeStopper CS-2014.DPII.FM.TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper OnGuard CS-2200WST Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9702 Kurzanleitung

CrimeStopper

CrimeStopper Fortress FS-20 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS.II Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2003DC II Series Handbuch

CrimeStopper

CrimeStopper CS-8716 Handbuch

CrimeStopper

CrimeStopper Super Rage CS-2011DP Bedienungsanleitung

CrimeStopper

CrimeStopper SP-200 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-882 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper HP-8850PR Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9228MX Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9703 Handbuch

CrimeStopper

CrimeStopper CS-2002DC Series III Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4011 Bedienungsanleitung

CrimeStopper

CrimeStopper SP-100 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9604PI Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung