CrimeStopper CS-882 OEM Bedienungsanleitung

CS-882 OEM

ALARM UPGRADE FOR FACTORY KEYLESS ENTRY

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of an Alarm Upgrade System by Crimestopper Security Products Inc.

This booklet contains the information necessary for installing, using, and maintaining this system. If any

questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support

number below.

*IMPORTANT INFORMATION:

This system does not improve or affect the range of the factory remote keyless entry transmitters.

This is an ADD-ON system only. The arm/disarm range of this system will be identical to that of the

Factory Keyless System’s lock/unlock range.

TECH SUPPORT

Mon-Fri 8:00 AM-4:30 PM Pacific Time

(800) 998-6880

REV. A 8/2002 SW: PG30500030CT1

INSTALLATION PRECAUTIONS & WARNINGS

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR

BAGS, ABS BRAKES, BATTERY, ETC.).

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering

column, or any other moving parts in the vehicle.

COMPONENT MOUNTING

Control Unit: DO NOT mount or wiring harness where they can become entangled with moving parts such as

brake/gas/clutch pedals, or the steering column! The control module should be mounted in a concealed location. Do

not mount the control unit in the engine compartment.

LED: Mount in a visible location on the dashboard or console.

Valet/Program Button: Mount button in a hidden but accessible location. It is REQUIRED for emergency disarm,

programming, and valet mode.

WIRING

VIOLET WIRE #1 & #2: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #1 NORMALLY OPEN

These wires the are for an on board Relay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Cut the selected

circuit you want to immobilize and connect each end to a VIOLET wire.

NOTE (1): This is a high-security, normally open connection. If the alarm system is unplugged or loses power,

the circuit will still be immobilized!

NOTE (2): This circuit has a maximum load of 10A and should NOT be used to interrupt a high current wire

such as an Ignition supply or Starter circuit from the ignition switch!

WHITE/RED: (-) NEGATIVE HORN/SIREN OUTPUT

Connect to wire that activates the factory horn. If you choose to use this output with a standard alarm (warble) siren,

then it should be connected to the black (negative) wire of the siren. Connect the red wire of the siren to constant (+)

12 Volts. NOTE: This wire is preset for a factory vehicle horn. You must change the programming for siren use. See

programmable option #15.

BLACK WIRE: SYSTEM CHASSIS GROUND

THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt from

the area to ensure a good connection.

RED WIRE: +12V POWER INPUT (15 amp fuse)

Connect to +12 Volt source with supplied fuse & holder. Connect to the vehicle’s battery Positive terminal.

WHITE WIRE: +12V FLASHING PARKING LIGHT OUTPUT X2 (15 amp fuse)

Connect to switched parking light wire at back of light switch. If this is not possible, connect directly to one of the

parking lights at the front of the vehicle. Many European vehicles require separate right and left circuits. Use this

second white wire to connect to the 2nd light circuit on your European vehicle. Otherwise do not use both white wires.

WIRING

ORANGE WIRE: (-) NEGATIVE STARTER DISABLE (Armed output)

Ground output when system is armed. This output is used for disabling the starter or to activate other optional devices

such as scanner LED’s, window control modules, voice modules etc. For starter kill, cut starter wire and connect

between 87A and 30 on a relay. Connect orange wire to 85 and connect 86 to an Ignition source that has voltage in

“ON” and “CRANKING” positions at the Ignition switch. (Starter disable relay not included)

PINK/WHITE WIRE: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #2 NORMALLY OPEN

PINK WIRE: ON-BOARD RELAY (10A) IMMOBILIZER CIRCUIT #2NORMALLY OPEN

These wires the are for an on boardrelay to immobilize the Coil or Fuel Pump Circuit in the vehicle. Cut the selected

circuit you want to immobilize and connect one end to the Pink wire and the other end to the Pink/White wire.

NOTE (1): This is a high-security, normally open connection. If the alarm system is unplugged or loses power,

the circuit will still be immobilized!

NOTE (2): This circuit has a maximum load of 10A and should NOT be used to interrupt a high current wire

such as an Ignition supply or Starter circuit from the ignition switch!

YELLOW WIRE: +12 VOLTS IGNITION SWITCHED

Connect to an Ignition wire that shows +12 Volts with the key in both “On” and “Start” positions.

BLACK/WHITE WIRE: +12 VOLTS POWER TRUNK RELASE INHIBIT INPUT(If Equipped)

Connect this wire to the positive side of trunk release solenoid. This input wire will allow the CS-882OEM system to

sense when the Trunk Release Button is pressed on the Factory Remote Control. This will prevent an unwanted false

alarm if your vehicle has a powered trunk/hatch release. At the instant a positive pulse is sensed on this wire, the

trunk trigger, shock sensor, and current sensing features are bypassed. If the trunk is then re-closed (sensed by trunk

pin) the zone will re-arm in 3 seconds, otherwise system is STILL ARMED EVEN THOUGH THE TRUNK IS OPEN and

must be disarmed with the Unlock Button before entering vehicle.

BLUE WIRE: (-) or (+) DOOR TRIGGER (PROGRAMMABLE, DEFAULT IS NEGATIVE)

Connect to door pin activation circuit in vehicle:

•Negative type door circuits show Ground when any door is opened and 12 volts when all doors are closed. Some

vehicles may have isolated door triggers. In this case you may need to run additional wires from other doors or go

directly to the wire at the vehicle’s dome light.

•Positive type door circuits show 12 Volts when a door is opened such as on many Ford/Mercury vehicles.

*TIP: Many recent vehicles have door pin switches incorporated in the door latch itself, therefore there are not any

“plunger” type door switches located in the door jamb. If your vehicle has no door pins, an alternative connection may

be at courtesy light or locating the door triggers at a control module elsewhere in the vehicle. Call Tech Support for

assistance.

WIRING

GREEN WIRE: (-) HOOD/TRUNK TRIGGER

Connect this wire to a grounding hood / trunk pin switch or to existing factory hood and trunk pin switches that read

ground when open. If no existing switches are available, new pin switches may be installed. Note: DO NOT mount

new pin switches in water pathways.

RED/WHITE: (+/-) Door Unlock Validation Signal INPUT: [Default Setting is Negative]

Connect to Vehicle’s Door Unlock Switch wire. NOTE: The module must be programmed for the correct signal polarity.

(Flipping switch on top of control module will change the input polarity.) This wire prevents system from being defeated

simply by pressing the vehicle’s unlock button at the door panel when triggered.

GREEN/WHITE: (+/-) Door Lock Validation Signal INPUT: [Default setting is Negative]

Connect to Vehicle’s Door Lock Switch wire. NOTE: The module must be programmed for the correct signal polarity.

(Flipping switch on top of control module will change the input polarity.) Prevents system from being armed when

manually pressing the vehicle’s Lock button at the door panel.

BLUE/BLACK: Door Unlock Signal INPUT:

Connect to Vehicle’s (+12V) Door Unlock (Solenoid/Motor) Wire.

YELLOW/BLACK: Door Lock Signal INPUT:

Connect to Vehicle’s (+12V) Door Lock (Solenoid/Motor) Wire.

**SEE DOOR LOCK MOTOR / VALIDATION WIRE CONNECTIONS NEXT PAGE

WIRING: MINI PLUGS

2-PIN PLUG (WHITE): PROGRAM/VALET BUTTON Connects to white plug on module.

2-PIN PLUG (RED): LED INDICATOR (RED FLASHING LIGHT) Connects to red plug on module.

3 PIN SENSOR PLUG:

WHITE Wire: Negative Signal

BLACK Wire: Sensor Ground

RED Wire Sensor +12V Power

SHOCK SENSOR: The sensor supplied with

this system does not require any additional

wiring. Simply mount the sensor in a suitable

location, plug it in, and adjust the sensitivity.

CURRENT SENSING

DIP SWITCH #4

OFF

CURRENT SENSING

The CS-882OEM system includes a current sensing circuit to monitor current

flow through the vehicles electrical system. If an intruder opens a door and the

interior lights turn on, the CS-882 system will detect a current drain and trigger

the alarm without having to connect (hardwire) this system to the interior dome

light circuit and hood/trunk pin switches. If your vehicle includes courtesy lights

in the trunk and/or under the hood, the system should also protect those areas

when in current sensing. Current sensor is off by default. See diagram at right.

CURRENT SENSING NOTES:

1. Current sensing may be a problem for you if your vehicle has a thermostatically controlled fan

system that may turn on after you have set the alarm and left the vehicle. The fan turning on will

cause a false alarm trigger.

2. Some vehicles with large or more then one battery will not operate well in current sensing mode

because there is not enough voltage drop for the unit to detect a light turning on. If you experience

problem with current sensing, please use the hard-wired door and hood/trunk inputs.

RESISTORS & DIODES

The enclosed diodes and resistors are only used for alternative installations that DO NOT +12V or Grounding

validations signals. (Door Lock/Unlock Switch wires).

Connect components as follows:

Yellow/Black: wire from CS882 connects to one side of resistor.

Remaining side of resistor connects to band end of diode.

Non-band end of diode (anode) connects to parking light switched +12 volt wire.

Blue/Black: wire from CS882 connects to one end of 2nd resistor.

Remaining side of resistor connects to band end of 2nd diode.

Non-band end of diode (anode) connects to door lock solenoid switch that switches from ground to +12 volts

when locking and unlocking.

2 31 4

NEGATIVE VALIDATION INPUTS

(TOP EDGE OF 882 MODULE)

2 31 4

POSITIVE VALIDATION INPUTS

(TOP EDGE OF 882 MODULE)

DOOR / LOCK & VALIDATION WIRES (TYPICAL INSTALLATION)

VALIDATION WIRES ON (MODE A = DIP SWITCHES 1-3 ON):

The Validation wires serve as a secondary input to prevent the

system from being armed or disarmed simply by pushing the unlock

button on the vehicle.

ARM/DISARM VALIDATION WIRES:

ARMING: The CS-882OEM system will NOT ARM if a NEGATIVE

(or POSITIVE*) pulse is sensed on the GREEN/WHITE wire. (The

Lock button on the door panel vehicle was pressed)

DISARMING: The CS-882OEM system will NOT DISARM if a

NEGATIVE (or POSITIVE*) pulse is sensed on the RED/WHITE

wire. (The Unlock button on the door panel was pressed).

*See Positive/Negative Signal setting diagrams at right and below.

FACTORY

POWER

LOCK

RELAYS

LOCK

SWITCH

(+) LOCK / MOTOR WIRE

(+) UNLOCK / MOTOR WIRE

YELLOW / BLACK BLUE / BLACK

GREEN / WHITE

RED / WHITE

+ / - LOCK SWITCH WIRE *

+ / - UNLOCK SWITCH WIRE *

(*Programmable for POS/NEG validation)

PROGRAMMABLE OPTIONS

1. Turn the Ignition ON and press the Override/Program button 7 times within 10 seconds.

2. Turn OFF Ignition. LED will flash slowly once per second as and indicator the system is in programming

mode.

3. Within 20 seconds, press the Override/Program button the number of times that corresponds to the feature

list below. The siren will chirp for each button press. DO NOT LOSE COUNT!! If you can hold down the

button for 3 seconds and release you get 2 chirps. A 3-second button press is the same as pressing the

button 10 times.

4. When you get to the desired option number, turn the Ignition from OFF to ON to toggle between the preset

and alternate settings. The siren will chirp once or twice indication which value the feature is at. See Below

for Option numbers, descriptions, and values. Ignition should be left in the OFF position once your have

the correct value.

5. At this time, if you need to change more options, repeat steps 3 & 4 above.

6. To exit programming Mode, Turn Ignition ON and press the Override/Program button once.

OPTIONS CHART

Option #

Option Description PRE-SET Value

(1 chirp) ALTERNATE

Value

(2 chirps)

1Flashing Lights ON OFF

6Siren Chirps ON OFF

8Passive Arming OFF ON

10 Door Trigger Input Polarity

(Blue wire) NEGATIVE POSITIVE

14 Allow Panic Mode OFF ON

15 Horn or Siren output

(White/Red wire) HORN SIREN

25 Restore all options to PRE

SET VALUES YES

OPERATION

ARMING

To arm the alarm and lock the doors, press the Lock button of your Factory Keyless Remote Control. The 882

OEM system will sense the Door Lock signal and Arm. The lights will flash once, the vehicle horn or siren will

chirp once. After 3 seconds, the LED indicator will begin flashing slowly and Immobilizer circuits become

active. This system is now armed and ready to protect the vehicle.

ALARM TRIGGERING:

If there is an intrusion into the vehicle or hard impact to the body the alarm will sound which consists of

flashing lights and siren or pulsing car horn for 30 seconds. After the 30 second alarm cycle duration the

system will stop, but is still armed. LED will begin flashing rapidly indicating the alarm has been triggered.

DISARMING:

To disarm the CS-882 OEM, press the Unlock button of your Factory Keyless Remote. The CS-882 OEM

system will sense the Door Unlock signal and Disarm. The lights will flash twice and the vehicle horn or siren

will chirp twice. The LED will stop flashing. If the system was tripped in your absence, then the siren or horn

will chirp 4 times and the lights will flash 4 times. If your hear 4 chirps/flashes, we recommend inspecting your

vehicle for a theft attempt or damage.

PASSIVE ARMING MODE (Programmable Option)

When programmed for Passive (Automatic Last Door Arming) the CS-882 will arm itself 30 Seconds after the

ignition is turned off and the last door has been closed. If a door is reopened, the system will wait for the door

to close before arming.

DUAL-STAGE SHOCK PROTECTION

If a low-level shock to the vehicle body is detected, the pre-warning sensor activates sounding 1 siren/horn

chirp and one light flash. If a hard impact to the vehicle occurs, the system will trigger for 30 seconds. Adjust

the shock sensor as needed by turning the control knob clockwise to increase sensitivity and counter-

clockwise to decrease sensitivity.

EMERGENCY OVERRIDE/DISARM

If the CS-882 system is armed and you have lost your Factory Keyless Remote or it stops working, you will

have to perform an emergency override. Enter your vehicle manually with the key, (this will trip the alarm) turn

the Ignition ON, and press override/program button 5 times within 8 seconds to disarm the system. The

system will chirp/flash 4 times when disarmed.

OPERATION

VALET MODE

To disable alarm functions of the 882 system, turn the Ignition ON and press the override/program button 3

times within 8 seconds. After 8 seconds, the dash LED turns on solid as an indicator that the system is in valet

mode. Repeat this steps to exit VALET mode. The LED will go out, system will chirp (2) times and the light

will flash (2) times when exiting valet mode.

When in VALET mode the siren will still chirp for lock/unlock confirmation even though alarm functions are

disabled. The CS-882 system will chirp 2 times when locking the doors and 3 times when unlocking the

doors.

PANIC MODE (Programmable Option)

To activate your system during an emergency situation or to attract attention to your vehicle, press the Lock

button on your remote 3 times within 5 seconds. This will activate a 30-second alarm trigger. Press any

button on your remote to disarm.

FACTORY TRUNK RELEASE SENSING

If the CS-882 system is installed in a vehicle with trunk pop or hatch release button on the Factory Remote,

there is a special input wire that will prevent the system from triggering if the trunk button on your remote is

pressed while the system is armed.

WIRING DIAGRAM

VALET/

IGN SW.

STARTER

STATUS LED

FUSE

BOX

IGNITION ON &

CRANKING VOLTAGE

STARTER WIRE

87A

CUT

RED

VIOLET

BLACK

WHITE/RED

(-) ARMED OUTPUT

(STARTER DISABLE)

IGN

SW.

ORANGE

WHITE

FUSE

15A

PARKING LIGHTS

SHOCK SENSOR

BATTERY

CS-882

OEM

PROGRAM

BUTTON

IMMOBILIZE

(Low-Current circuit)

VIOLET

+12V

SIREN

HORN

CHASSIS

GROUND

WHITE

PARKING LIGHTS

FUSE

15A

FUSE

15A

USE ONLY FOR

EUROPEAN VEHICLES

WITH 2 PARKING LIGHT

CIRCUITS.

PINK/WHITE

PINK

LED: RED PLUG

VALET: WHITE PLUG

CONNECTS TO POSITIVE

SIDE OF TRUNK RELEASE

OF TRUNK SOLENOID

NEG. or POS

DOOR PIN SW.

(Programmable)

NEGATIVE

PIN SW.

YELLOW/BLACK BLUE/BLACK

NEG. SIREN or HORN OUTPUT

CHASSIS GROUND

CUT

COIL or FUEL PUMP

+12V POWER INPUT

+12V PARKING LIGHT OUTPUT

+12V PARKING LIGHT OUTPUT #2

ON-BOARD IMMOBILIZER

ON-BOARD IMMOBILIZER #2

IMMOBILIZE

(Low-Current circuit) CUT

COIL or FUEL PUMP

YELLOW

+12V IGN. INPUT

BLACK/WHITE

BLUE

GREEN

(-)NEG. HOOD/TRUNK INPUT

RED/WHITE

GREEN/WHITE

*POS or (-)NEG. LOCK SW. INPUT

*POS or (-)NEG. UNLOCK SW. INPUT

POSITVE UNLOCK MOTOR INPUT

POSITVE LOCK MOTOR INPUT

(*Programmable)

SEE PAGE #5 OF MANUAL

Andere Handbücher für CS-882 OEM

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper Super Rage CS-2012DPII-TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2004 WDC Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2002 Bedienungsanleitung

CrimeStopper

CrimeStopper SP-500 Systemhandbuch

CrimeStopper

CrimeStopper Super Rage CS-2012TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper SuperPage III CS-2006FM Montageanleitung

CrimeStopper

CrimeStopper CS-2000DPII TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-790MX Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8700 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2015.FM.RevB Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2000DPII SERIES IV Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Systemhandbuch

CrimeStopper

CrimeStopper CS-9602PI Betriebsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper HP-9225MX Kurzanleitung

CrimeStopper

CrimeStopper OnGuard CS-2200WST Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9206SE Handbuch

CrimeStopper

CrimeStopper CS-9600 Technisches Datenblatt

CrimeStopper

CrimeStopper Super Rage CS-2011DP Bedienungsanleitung

CrimeStopper

CrimeStopper Super Page V CS-2014TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4008 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2002DC Series III Bedienungsanleitung

CrimeStopper

CrimeStopper Super Rage CS-2011DP Systemhandbuch

CrimeStopper

CrimeStopper The Informer CS-2015FM / TW1 Series Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung