CrimeStopper CS-865RKE II Series Handbuch

CS-865RKE Series II

REMOTE KEYLESS ENTRY SYSTEM

INSTALLATION & OPERATING INSTRUCTIONS

INTRODUCTION:

CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products

Inc. This booklet contains the information necessary for installing, and operating your system. If any

questions arise, contact your installation dealer or Crimestopper Security Products Inc. at the Tech Support

number below.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY FEATURES: These are features that must be connected in order for the system to operate

properly i.e. Power & Ground, along with the Primary features of Power Locks & Flashing Lights.

-OPTIONAL FEATURES: Optional features are connected only if desired or agreed upon by the installing

dealer i.e. Driver’s Separate Unlock, Horn Chirp, Dome light illumination, Trunk Pop, etc. These features may

require additional parts and labor charges. Consult with your installer and come to an agreement about your

optional features before installation. NOTE: The LED is required for programmable options. See page 10.

TECH SUPPORT This device complies with FCC Rules part 15. Operation is subject to the

following two conditions: 1) This device may not cause interference, and (2)

this device must accept any interference that may be received, including

interference that may cause undesired operation. The manufacturer is not

responsible for any radio or TV interference caused by unauthorized

modification to this equipment. Such modification could void the user's

authority to operate the equipment.

Mon-Fri 8:00 AM-4:30 PM Pacific Time

(800) 998-6880

www.crimestopper.com

[email protected]

REV. B 03.2004

TABLE OF CONTENTS

Pre-Installation & Component Mounting……………………..…………………………………………………2-3

Wiring……..…………………………………………………………………………………………………….…….3-4

Power Door Lock Wiring……………………………………………………….………..……………….…..……4-6

Jumper Diagram……………………………………………………………………………………………………….7

System Wiring Diagram.………………………………………………..……………………………………...…….8

Transmitter Programming……………………………………………………………………………………………9

Option Programming / Option Reset………………………….…………………………….…………......…10-11

Operating Instructions………………………..…………………………………………………………..…….12-14

2-Vehicle Operation………………….…………………………….…………………………….……………..……15

PRE-INSTALLATION CONSIDERATIONS

To ease installation, we suggest that you READ THIS MANUAL before beginning your installation.

BEFORE BEGINNING, check all vehicle manufacturer cautions and warnings regarding electrical service (AIR

BAGS, ABS BRAKES, ENGINE / BODY COMPUTER AND BATTERY).

PLAN OUT YOUR INSTALLATION and determine most suitable locations for all components to be placed.

These components include: the module itself, valet/program button and possible relays. Allow enough wire to

create a service loop with strain relief, should servicing be required.

DAMAGE resulting from incorrect installation or failure to follow guidelines stated in this book will not be

covered under warranty and subject to repair or replacement charges.

USE A VOLT/OHM METER to test and locate all connections. Test Lights can damage a vehicle’s computer

systems.

ADDITIONAL PARTS, which are not included with this unit, may be needed for your particular vehicle. .

These items may include extra relays (Part#CS-402A) or Special “Data Bus” interface modules.

DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLED with brake, and gas pedals, steering

column, or any other moving parts in the vehicle.

REMOVE MAIN SYSTEM FUSE (S) before jump starting the vehicle or charging the vehicles battery.

COMPONENT MOUNTING

CONTROL MODULE: Locate the module underdash as high as possible. Driver’s Side usually provides an

easy location for the majority of the wiring connections. The antenna wire should be routed away from any

metal if possible. DO NOT alter the length of the antenna wire, or ground the antenna wire.

OVERRIDE / PROGRAM BUTTON: Mount the button in a hidden but accessible location. It is used for

emergency-disarm (when optional starter disable is installed) without the use of the transmitter and for

programming features of this unit.

LED (Optional): The optional Red LED provides a useful theft deterrent. The LED blinks after you lock the

vehicle with your remote simulating an alarm system. The LED is also used when programming options. If

you decide to install the LED, choose a visible location in the dash or console for a location.

WIRING

WHITE WIRE: +12V or (-) NEGATIVE PARKING LIGHT (Jumper Selectable On-Board Relay 10A)

Connect to switched +12V parking light wire at back of light switch. If this is not possible, connect directly to

one of the parking lights at the front of the vehicle. If your vehicle requires a (-) Negative Ground signal to

activate the parking lights, then you have to open the control and move the jumper located on the circuit board

inside the unit. For European vehicles with separate right and left circuits, use a dual relay or 2 diodes to

separate the output signal. The DEFAULT output is POSITIVE. SEE PAGE 7

BLACK/YELLOW WIRE: (-) AUXILIARY REMOTE OUTPUT 3 (Optional, requires relay)

This wire provides a Negative momentary output for activation of optional or auxiliary devices. It is controlled

by Pressing and Holding Buttons (2) Unlock and (4) Panic together.

BLACK/WHITE WIRE: (-) NEG. or +12V DOME LIGHT (Jumper Selectable On-Board Relay-10A)

Connect to dome light activation circuit for Negative type circuits. For Positive type circuits, open the control

module and move the jumper the plug as shown in illustration. The DEFAULT is NEGATIVE. SEE PAGE 7.

BLUE/WHITE WIRE: (-) PASSENGER(S) DOOR UNLOCK OUTPUT (Optional, requires relay)

Connects to unlock circuit for passenger door(s) when using separate driver’s door unlock option. See DOOR

LOCK WIRING for configuration options.

WHITE/RED WIRE: (-) AUXILIARY REMOTE OUTPUT 2 (Optional, requires relay)

This wire provides a Negative momentary output for activation of optional or auxiliary devices. It is controlled

by Pressing and Holding Button (1) Lock.

WIRING

ORANGE WIRE: NEGATIVE ARMED OUTPUT

This wire provides a constant GROUND output when system is locked with the remote transmitter. This

output can used for a starter disable relay, or a device such as a window roll-up module. See System Wiring

Diagram. On page

GRAY WIRE: (-) AUXILIARY REMOTE OUTPUT 1 (Optional, requires relay)

Negative Pulsed output controlled by pressing Button #3 (Trunk Symbol) for at least 1 second.

BROWN/WHITE: (-) HORN HONK/CHIRP OUTPUT (Optional, requires relay)

This wire provides a negative pulse output to honk/chirp the factory horn for audible lock/unlock confirmation.

Connect Brown/White to terminal 85 of a relay. Connect terminal 86 to +12V Constant. Connect terminal 87

to +12V or GROUND depending on the type of horn activation circuit in the vehicle. Connect terminal 30 to

the horn activation circuit. NOTE: Many vehicles use a Negative type of horn circuit, however we recommend

that you test the circuit on your vehicle before making any connections to avoid any possible damage.

GREEN WIRE: NOT USED (No Connection)

YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS

Connect to an ignition wire that shows +12 Volts when the key in both “On” and “Start” positions.

BLACK WIRE: SYSTEM CHASSIS GROUND

THIS WIRE MUST BE CONNECTED TO CHASSIS METAL OF THE VEHICLE. Scrape away any paint or dirt

from the connection point to ensure a good connection. Keep ground wire short.

RED WIRE: +12V POWER INPUT (15 amp fuse)

Connect to +12 Volt source with supplied fuse & holder. Recommended location for this connection is at the

vehicle battery positive terminal.

POWER DOOR LOCK WIRING

6 PIN DOOR LOCK OUTPUT PLUG (On-Board Relays):

VIOLET (Fused 10A): UNLOCK Normally Open (Terminal 87 On-board Unlock Relay)

BROWN/BLACK: UNLOCK Normally Closed (Terminal 87A On-board Unlock Relay)

BLUE/BLACK: UNLOCK Output (Terminal 30 On-board Unlock Relay)

VIOLET/BLACK (Fused 10A): LOCK Normally Open (Terminal 87 On-board Lock Relay)

WHITE/BLACK: LOCK Normally Closed (Terminal 87A On-board Lock Relay)

GREEN/BLACK: LOCK Output (Terminal 30 On-board Lock Relay)

POWER DOOR LOCK WIRING

NEGATIVE TRIGGER DOORLOCK WIRING POSITIVE TRIGGER DOORLOCK WIRING

BLUE/BLACK

FUSED

VIOLET

+12V

GREEN/BLACK

VIOLET/BLACK

FACTORYFACTORY

POWERPOWER

LOCKING

ULUL

RELAYS

AFTERMARKET ACTUATOR WIRING

REVERSE POLARITY DOOR LOCK WIRING

FUSED

FUSED +12V

+12V

CUT

BROWN/BLACK

WHITE/BLACK

NOT USED

BLUE/BLACK

VIOLET

GREEN/BLACK

VIOLET/BLACK

BROWN/BLACK

WHITE/BLACK

NOT USED

LOCK WIRE

UNLOCK WIRE

BLUE/BLACK

VIOLET

GREEN/BLACK

VIOLET/BLACK

BROWN/BLACK

WHITE/BLACK

Master Switch

LOCK WIRE

UNLOCK WIRE

BLUE/BLACK

VIOLET

GREEN/BLACK

VIOLET/BLACK

BROWN/BLACK

WHITE/BLACK

LOCK WIRE

UNLOCK WIRE

CS-865RKE SEPARATE DRIVER’S DOOR UNLOCK DIAGRAMS

BLUE / WHITE

DRIVER'S

DOOR MOTOR

(+) UNLOCK WIRE CUT

WHITE / BLACK

GREEN / BLACK

BLUE / BLACK

BROWN / BLACK

VIOLET / BLACK

8685

3087A

+12V

FUSED

CUT

MASTER

SWITCH

DRIVER PRIORITY UNLOCK with NEGATIVE TYPE DOOR LOCKS

BLUE / WHITE

DRIVER'S

DOOR MOTOR

ULUL

FACTORY LOCK

RELAYS

(+) UNLOCK WIRE CUT

+12V

FUSED

WHITE / BLACK

GREEN / BLACK

BLUE / BLACK

BROWN / BLACK

VIOLET

NOT USED

DRIVER PRIORITY UNLOCK with REV. POLARITY DOOR LOCKS

VIOLET / BLACK

VIOLET

JUMPER PIN DIAGRAM

The jumper plugs inside the control module determine the unit's (+12V) or (-) Negative Parking & Dome Light

Relay outputs (White & Black/White wires). Use the jumper pins to change the Positive or Negative Polarity of

the outputs as required for your particular installation. (Default = Positive for Parking Light and Negative for

Dome Light) See diagram below.

JUMPER

PLUG

SIDE VIEW

JUMPER

PINS

(-) NEG. DOME LIGHT

CS-865RKE II MODULE

+12V PARKING LIGHT

(DEFAULT)

TOP VIEW OF JUMPER PINS

(-)NEG. PARKING LIGHT +12V DOME LIGHT

(DEFAULT)

Parking Light: P4 Dome Light: P5

JUMPER

SYSTEM WIRING DIAGRAM

2nd Time for 2-Step Unlock

Press UNLOCK Button a

FUSE

BOX

BATTERY

IGN

SW.

Parking Lights

ORANGE

WHITE / RED

BLUE / WHITE

BLACK / YELLOW

WHITE/BLACK

RED

BLACK

YELLOW

GREEN

BROWN/WHITE

GRAY

(-) AUX. OUTPUT #3

+12V or (-) Neg. Dome Light

Output. (On-board 10A Relay)

(-) Passenger Unlock Ouput:

(-) AUX. OUTPUT #2

8586

87A

CUT

START WIRE

STARTER

OPTIONAL

STARTER DISABLE WIRING

+12V or (-) Parking Light Output

(-) Negative Armed Output

(Relay not included)

+12V Power Input

Chassis Ground

IGN

SW.

+12V Ignition Input

NOT USED

(-) Negative Horn Output

(-) Negative Trunk Pop Output (AUX. 1)

12 PIN MAIN

HARNESS

6 PIN DOOR LOCK

HARNESS

+12V or (-) Neg. Parking Light

Output. (On-board 10A Relay)

WHITE

BROWN/BLACK

VIOLET/BLACK

BLUE/BLACK

GREEN/BLACK

VIOLET

UNLOCK

Normally Open (Terminal 87 On-Board Unlock Relay)

LOCK

Normally Open (Terminal 87 On-Board Lock Relay)

UNLOCK

Normally Closed (Terminal 87A On-Board Unlock Relay)

UNLOCK

Output (Terminal 30 On-Board Unlock Relay)

LOCK

Output (Terminal 30 On-Board Lock Relay)

LOCK

Normally Closed (Terminal 87A On-Board Lock Relay)

LED

OVERRIDE/

PROGRAM

BUTTON

(OPTIONAL)

2 PIN BLUE HARNESS

2 PIN RED HARNESS

MAIN DOORLOCK

HARNESS HARNESS

PROGRAM

BUTTON

LED

CS-865RKE Module

LEGEND:

BLACK / WHITE

CS-865RKE II TRANSMITTER PROGRAMMING

NOTE: All transmitters must be learned at the time of programming. This system can learn up to 4 remotes.

1. Turn key to the ON position and press program button 4 times.

2. After a short delay, the unit will flash the parking lights 4 times.

3. Press the Button #1 (Lock) on the remote you wish to program.

4. You should get 1 light flash. Press button #1 of a second transmitter, the unit will flash 2 times. Press

the lock button on a 3rd or 4th transmitter for up to 4 total. Note: The unit will not flash the lights when

learning the 4th code. Turn key off to exit programming mode.

IGN

OFF

WAIT FOR

4 FLASHES

PRESS 4X's

FLASH 2, 3, or 4 X's

IGN

OFF

PRESS LOCK BTN

LIGHTS

PANIC

OPTION PROGRAMMING

To change programmable options, follow steps below.

1. Turn the Ignition ON and press the Override/Program button 5 times.

2. The parking lights will flash 5 times and status LED will be on solid.

3. Within the next few seconds, press the Override/Program button [again] the number of times that

corresponds to the options chart below. Parking lights and/or optional horn should chirp for each button

press. Don’t lose count!

4. When you get to the desired option number, quickly press the appropriate button on the remote control

according to the chart below. The system will provide 1 chirp/flash for Button 1 (Lock Symbol) and 2

chirps/flashes for button 2. (See Option Chart for numbers, descriptions, and values.)

5. Turn Ignition off. Change one option at a time repeating these same steps 1-4. When you are finished

customizing options, check operation to see if the option(s) have changed.

PROGRAMMING OPTIONS CHART * = DEFAULT SETTING

Option # Option Description Selection Lock Button Unlock

Button

1. Auto Lock & Unlock with

Ignition

ON or OFF ON* OFF

2. Double Unlock Pulse ON or OFF OFF* ON

3. Horn Chirp ON or OFF ON* OFF

4. Lock/Unlock Pulse Time 0.8 Sec. or 3 Sec. 0.8 Sec.* 3 Sec.

5. Passive Starter Lock &

Disable

ON or OFF OFF* ON

6. Ignition Trigger ON or OFF OFF* ON

7. Extended Horn Chirp Normal or

Extended

Normal* Extended

PROGRAMMABLE OPTION DESCRIPTIONS:

1. AUTOLOCK / UNLOCK WITH IGNITION

Controls whether the doors will automatically lock when the ignition is turned on and will unlock when the

ignition is turned off. Note: When Separate Driver’s Door Unlock feature is installed, only driver’s door

will unlock when IGN. is turned off. 10

Andere Handbücher für CS-865RKE II Series

Inhaltsverzeichnis

Andere CrimeStopper Fernstartsystem Handbücher

CrimeStopper

CrimeStopper Ezee Start EZ-90 Bedienungsanleitung

CrimeStopper

CrimeStopper RS700 IIIER Bedienungsanleitung

CrimeStopper

CrimeStopper RSX-G6 Bedienungsanleitung

CrimeStopper

CrimeStopper EZEE Start EZ-45DP Bedienungsanleitung

CrimeStopper

CrimeStopper CoolStart RS800 Series II Bedienungsanleitung

CrimeStopper

CrimeStopper RS-999TW1/TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper RS-800 Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS-3 Bedienungsanleitung

CrimeStopper

CrimeStopper COOL START RS-901 Bedienungsanleitung

CrimeStopper

CrimeStopper RS1-G4 Cool Start Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS-1405DP Bedienungsanleitung

CrimeStopper

CrimeStopper COOL START RS-900 Bedienungsanleitung

CrimeStopper

CrimeStopper LC-1 Bedienungsanleitung

CrimeStopper

CrimeStopper COOLSTART RS-830 Bedienungsanleitung

CrimeStopper

CrimeStopper SP-500 Bedienungsanleitung

CrimeStopper

CrimeStopper EZEE START EZ-10 Bedienungsanleitung

CrimeStopper

CrimeStopper Ezee Start EZ-64TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper COOL START RS-900 Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS-850 Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS-7 Bedienungsanleitung

CrimeStopper

CrimeStopper RS900/RS901 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-830RKE Bedienungsanleitung

CrimeStopper

CrimeStopper PS01-G5 Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS7-G5 FM Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch

Rooboost

Rooboost RB-1750WP Bedienungsanleitung

Schumacher

Schumacher INSTANT POWER IP-75C Bedienungsanleitung