CrimeStopper COOL START RS-901 Bedienungsanleitung

RS900ER / RS901 SERIES III

OPERATING INSTRUCTIONS

CONGRATULATIONSonyourchoice ofa CoolStart™ Remote Engine Starter by Crimestopper Security Products

Inc. This booklet contains the information necessary for using & maintaining your remote start system. If any

questions arise, contact your installation dealer or Crimestopper Security Products Inc. at (800) 998-6880.

*IMPORTANT NOTE-RS901 MODEL:

When using an RS901 Expansion Module activated by a Host Alarm or a Factory Keyless Entry, the Infinity Run

Mode feature will not be available.

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident resulting from the use of this

equipment. This system is designed to be professionally installed into a car or vehicle in which all items, such as parking brake and

all associated components, door switches, transmission shift linkage, throttle linkage, and all engine safety features, are in perfect

working condition.

DO NOT install the Remote Engine Starting System on MANUAL TRANSMISSION vehicles. If accidentally left in gear the

vehicle could become a self-propelled threat to life and property.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this system and its safety

features. B) Check for proper operation of these safety features prior to accepting delivery of the vehicle from the installation facility.

C) Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features.

D) Always leave the doors and windows closed and locked to protect against accident and theft.

DO NOT remote start the vehicle in a closed garage. Make sure that the garage door is open or there is adequate ventilation.

Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes.

IT IS ABSOLUTELY THE OWNERS SOLE RESPONSIBILITY TO: make certain the vehicle PARKING BRAKE is properly adjusted

and will hold the vehicle securely in all parking conditions, and to periodically check and maintain proper adjustment.

This device complies with FCC Rules part 15. Operation is subject to the following

two conditions: 1) This device may not cause interference, and (2) this device must

accept any interference that may be received, including interference that may

cause undesired operation. The manufacturer is not responsible for any radio or

TV interference caused by unauthorized modification to this equipment. Such

modification could void the user's authority to operate the equipment.

OPERATING THE REMOTE TRANSMITTER (RS900ER ONLY)

The transmitter supplied with this system has Four (4) buttons / channels. The button configuration is Factory-

set and unchangeable.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING -SUCCESSFUL START:

1) Press remote start button or for RS901 model activate Green Start input wire.

2) Parking lights flash once, then turn on solid, Ignition/Acc On.

3) After 6 seconds Starter Motor engages, Parking lights and Acc circuits turn off while cranking.

4) Engine Starts and Runs. Parking Lights and Acc turn back on, Doors Lock.

5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can be

turned off with remote transmitter or for RS901 model, activating the Green Start input wire.

AFTER

IGN

STARTER

THEN

START

FLASH 1X

SOLID

SEC.

#1 #2

START

LOCK

TRUNK REMOTE

START

UNLOCK

RIME

TOPPER

POP

NOTE:

When using the optional

Starter Disable feature with

out

power door locks, be certain to

install the supplied L.E.D. which

will be your only

indication that

the Starter Disable is active. You

must press the UNLOCK button on

the transmitter if the L.E.D. is

flashing or the vehicle will not

start.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING -UNSUCCESSFUL START

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then

attempts to restart the engine a 2nd and 3rd time. Forhard starting engines,the unit willallow astarter crank timeof

upto13 secondsmaximum. This shouldprovide amplecranking timefor difficultstarts, butislimitedto 13seconds

to help prevent damage to the starter from over cranking in the case of a malfunctioning unit.

1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 above of "Successful Start".

2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER

ATTEMPTS WILL BE MADE AUTOMATICALLY

TURNING OFF A REMOTE STARTED ENGINE:

1) Engine is running in Remote Start (Parking lights ON).

2) Press Remote Start button or for RS901 model activate Green Start input wire.

3) Engine turns & parking lights OFF, Doors remain locked or will re-lock/re-arm if applicable.

IDLE DOWN MODE:

Thismode allowsthe unitto takeoveroperation ofthe parkedvehicle whilethe ignitionkey isremovedand youexit

the vehicle. The vehicle is put into a remote running condition before you exit and it will remain running for the

programmed run time or until you come back.

Examples:

•You pull up to a convenience store for a quick stop, "Idle Down" mode keeps engine running when you exit the

vehicle, (with keys in hand) remote lock doors or arm alarm. When you return, unlock or disarm alarm, turn

ignition ON and drive away.

•On some Turbocharged vehicles it is recommended that the driver leave the car at idle for a short time

before turning the car off to allow the turbo to cool down.

START

REMOTE ENGINE CONTROL

IDLE DOWN MODE -EXITING THE VEHICLE:

1) With engine running, press Remote Start button or for RS901 model activate Green remote start input wire.

2) Parking Lights will turn ON.

3) Doors will unlock, or if brake pedal is being depressed doors will unlock when it is released.

4) Turn OFF Ignition and remove key. Engine should remain running.

5) Exit vehicle then remote lock doors if desired.

6) Engine will remain running for programmed run time or until you return (whichever comes first).

ENTERING A VEHICLE DURING “IDLE-DOWN” or “INFINITY RUN” MODES:

1) With engine running in "IDLE DOWN" (parking lights ON), unlock door or (Remote unlock or disarm alarm if

applicable)

2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)

3) TurnIgnition to ON/RUNposition, then depressbrake pedal toreset theRemote Starter. Parking lightswill turn

off. Then drive away.

IGN

SOLID

OFF

START

UNLOCK

SOLID

IGN

OFF

START

FLASH 2X

UNLOCK

REMOTE ENGINE CONTROL

INFINITY RUN MODE (RS900 ER III ONLY)

Thismode canonly beengaged when"Idle Down"is beingengaged. It allows thevehicle engineto remainrunning

INDEFINITELY after the programmed run time elapses. This mode will allow the vehicle to be left running and

unattended without the ignition key in the switch preventing the vehicle from being stolen. This mode can be

beneficial to law enforcement, commercial, or work trucks that need to remain running unattended for long periods

of time.

INFINITY RUN MODE –EXITING THE VEHICLE: (NOT AVAILABLE ON RS901)

1) Have engine running with the Key, then press the Start button on the transmitter once, pause a few seconds,

then press the remote start button a second time.

2) Parking Lights will start flashing, and doors will unlock.

3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.

4) Thevehicle’s parkinglights willflashfor theprogrammed runtime of12,24, or36, or48 minutesandthen switch

to solid while motor runs indefinitely or until fuel supply runs out.

TIMED SELF START MODE

This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run time.

This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. Be sure that the

vehicleis outdoorsor ina wellventilated area. Oncethe timedself-start modeisset, theunitwill startevery 4 hours

and run for the programmed time. To reset this mode either start the vehicle with the key or via remote control.

IGN

OFF

FLASH FOR PROGRAMMED

RUN TIME, THEN SOLID

START

REMOTE ENGINE CONTROL

TIMED SELF-START MODE –EXITING THE VEHICLE:

1) Have engine running with the Key, then press the Start button or for RS901:model activate Green start input

wire.

2) Within 10 seconds press the valet/program button once.

3) Parking Lights will turn OFF for about 5 seconds, and doors will unlock.

4) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.

5) To turn off the engine, press the remote start button or for RS901 model activate Green Start input wire. The

parking lights will flash 4 TIMES as a confirmation that the unit is in Timed Self-Start Mode.

6) The Vehicle will Start by itself every 4 hours until driven with key or started via remote control.

CONVENIENCE AND SAFETY FEATURES

OEM INTERFACE: (FACTORY UPGRADE)

The RS901 Series III Expansion Module includes a programmable interface feature that allows control of most

remote start features through an existing factory remote keyless entry system. The RS901 Expansion module can

be installed as an upgrade to a Factory Keyless Entry System. This is referred to in this manual as activating the

Green Start input. Pressing a button on the Factory remote 3 times will activate a start. This type of installation is

usuallyconnected tothe lockcircuit inthe vehicle,therefore pushingthe lockbuttonon theFactory Remote3times

will produce a remote engine start or turn off a remote started engine.

PASSIVE STARTER DISABLE:

This RS900/901 Series III includes a programmable feature to allow the Optional Starter Disable to activate

automatically 1 minute after the ignition is turned off. This feature may provide insurance discounts or meet

insurance requirements in your providence.

KEYLESS ENTRY (POWER DOOR LOCK CONTROL)

Thissystem enables youto remotelylock and unlockthe vehicle’s doors (if equippedwith power locks)through the

transmitter for safety and convenience. This feature may require extra labor and/or parts to install.

REMOTE LOCK / UNLOCK

1) Press the Lock or Unlock transmitter button as you leave or come near the vehicle.

2) Parkinglights willflash twicefor unlockand oncefor lock. Ifvehicle isremote started,enginewillremainrunning

and lights will flash but return to solid indicating engine is still being controlled by the remote starter.

NOTES: Doors lock automatically when vehicle is Remote Started. Starter Disable/Anti-grind is also

enabled/disabledwith thelock/unlock buttons. Ifan anti-grind/starterkillrelayis installed onavehiclewithoutpower

door locks, the lock and unlock buttons on the remote control must still be utilized to operate the Starter disable.

CONVENIENCE AND SAFETY FEATURES

REMOTE TRUNK RELEASE (OPTIONAL)

This feature, if installed, will remotely release a factory electronic trunk or hatch through the transmitter. This

feature may require extra labor and/or parts to install. To operate, press Button #3 (Trunk) release button to

remotely open trunk or hatch.

VALET MODE / STARTER DISABLE OVERRIDE

Before servicing your vehicle or handing the keysover to a Valet we recommend putting the unit into valet mode.

The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON

position, press and hold Program/Valet switch for 6 seconds. The LED will turn on solid and the system is now in

valet. Performthis procedureagain toexit ofValet mode. The keylessentry willstillfunction normallywhile invalet

mode. In the event of a lost or broken transmitter, perform this step to override the Starter Disable (If installed).

HOOD OPEN SAFETY SWITCH

Prevents the engine being Remote Started when hood is open and will abort a remote start if running. Eliminates

risk of injury to someone working under the hood of the vehicle. If a Remote Start is requested with the hood open,

the lights will flash twice, Ignition will not turn on, and the unit will not attempt a start.

BRAKE PEDAL RESET CIRCUITRY

Preventsstarting orshuts off aremote startedvehicle whenthiscircuit isactive oractivated. Preventsunauthorized

tampering. Thiscircuit shutsthe systemdown immediately when brake pedal is pressed if key is not in ignition and

turned to the run position.

OEM ALARM INTERFACE

This feature is designed to Disarm and Re-arm Factory equipped security systems in conjunction with remote start

and keyless entry (if needed). This feature will maintain the original integrity and security of your vehicle’s factory

equipped systems before, during, or after timed out or aborted remote start.

ANTI-GRIND / STARTER DISABLE

Prevents User from accidentally grinding the starter if the Ignition key is turned too far to the start position while

engine is already running from the remote starter. Starter circuit is automatically disabled when doors are locked

using remote as an added security feature.

NOTE:

Intheevent ofa majormalfunction, performingelectrical service,or jumpstartingthe vehicleyoushouldremovethe

main Power Fuse(s) to protect the unit from possible damage.

TRANSMITTER PROGRAMMING

TRANSMITTER PROGRAMMING:

Note: All transmitter codes must be learned at time of programming!! The RS900 allows storage of up to 4

different transmitter codes.

1. Open Hood.

2. Turn key to the ON position. (Doors will lock if Autolock is programmed)

3. Press Programming button 4 times, then after a few seconds the unit flash the parking lights 4 times.

4. Press button #1 of the transmitter to be coded. You should get 2 light flashes indicating the unit is waiting for a

2nd code, then press button #1 of a second transmitter, the unit will flash 3 times indicating its waiting for the 3rd

codeand 4flashes forthe 4th code. Ifall 4codes arelearned, theunit willautomaticallyexit codelearning mode,

otherwise turn key off and close hood.

TRANSMITTER PROGRAMMING:

IGN

OFF

WAIT FOR

4 FLASHES

PRESS 4X's

2, 3, OR 4 FLASHES

START

RIME

TOPPER

CRIMESTOPPER SECURITY PRODUCTS, INC. 1770 SOUTH TAPO ST. SIMI VALLEY, CA. 93063

RS900III OPS REVA 07.14.00

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CrimeStopper Fernstartsystem Handbücher

CrimeStopper

CrimeStopper Cool Start RS-850 Bedienungsanleitung

CrimeStopper

CrimeStopper REVO-1 Series Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9704 Bedienungsanleitung

CrimeStopper

CrimeStopper RS-800.III Bedienungsanleitung

CrimeStopper

CrimeStopper cool start RS2-G3 Bedienungsanleitung

CrimeStopper

CrimeStopper LC-1 Bedienungsanleitung

CrimeStopper

CrimeStopper RS-999.FM Bedienungsanleitung

CrimeStopper

CrimeStopper RS-901.II Bedienungsanleitung

CrimeStopper

CrimeStopper SP-400 Bedienungsanleitung

CrimeStopper

CrimeStopper RS-901.V Bedienungsanleitung

CrimeStopper

CrimeStopper SP-500 Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS-1300DP Bedienungsanleitung

CrimeStopper

CrimeStopper Pro Start LCPRO-3 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-870RKE Bedienungsanleitung

CrimeStopper

CrimeStopper EZEE START EZ-10 Bedienungsanleitung

CrimeStopper

CrimeStopper PS01-G5 Bedienungsanleitung

CrimeStopper

CrimeStopper Ezee Start EZ-777 FM Bedienungsanleitung

CrimeStopper

CrimeStopper RS900/RS901 Bedienungsanleitung

CrimeStopper

CrimeStopper EZ-777 Bedienungsanleitung

CrimeStopper

CrimeStopper RS-800.IV Bedienungsanleitung

CrimeStopper

CrimeStopper CS-865RKE II Series Handbuch

CrimeStopper

CrimeStopper RS-901.III Bedienungsanleitung

CrimeStopper

CrimeStopper Cool Start RS-3 Bedienungsanleitung

CrimeStopper

CrimeStopper ezee Start EZ-777 VII Bedienungsanleitung

Beliebte Fernstartsystem Handbücher anderer Marken

AstroStart

AstroStart 803U Bedienungsanleitung

Durite

Durite 0-649-20 Handbuch

EINHELL

EINHELL BT-PS 1000 Handbuch

Linear

Linear ACCESS AK-21 Technische Daten

Soundstream

Soundstream TARANTULA RS.2 Bedienungsanleitung

Jaycar Electronics

Jaycar Electronics MB3752 Bedienungsanleitung

Ultra Start

Ultra Start 72 Series Bedienungsanleitung

ADS

ADS FLASHLOGIC FLRSVW1 Bedienungsanleitung

Selecta

Selecta JS012 Bedienungsanleitung

Black Widow Security

Black Widow Security BW RAS 400 Bedienungsanleitung

Vector

Vector Power City DK080706 Beilage

Code Alarm

Code Alarm CA-535 Bedienungsanleitung

Ozito

Ozito OJS-800 Bedienungsanleitung

Profi-Partner

Profi-Partner 46387 Bedienungsanleitung

EZ STARTER

EZ STARTER EZ-45 Bedienungsanleitung

Viper

Viper 4204 Bedienungsanleitung

Essex Electronics

Essex Electronics KE-1701 Bedienungsanleitung

EINHELL

EINHELL EGS 3600 Handbuch