Crosswater MPRO US-PRO418 Bedienungsanleitung

Installation Instructions

6-1/2"

2-5/8"

9-3/4"

4-7/8" dia.

35"

39-1/2"

Adjustable

wrench

Channel

locks

Plumbers’ putty

or caulking

Flat head

screwdriver

Cross head

screwdriver

Hexagonal

key

MPRO Floor-mount Thermostatic Tub Filler

US-PRO418

Introduction

Installation notes

The faucets in this range are single flow (hot and cold water mix in the

body) and should therefore be supplied with hot and cold water at

balanced pressures. If the faucets are not supplied at balanced

pressures then the mixer will not function correctly.

The minimum water pressure required for these faucets is 20 psi.

The maximum water pressure is 60 psi, (beyond which pressure-

reducing valves must be installed).

The faucets are fitted with quarter-turn ceramic disc cartridges which

provide a good flow rate with very smooth movement.

IMPORTANT: Before beginning installation, check for any damage

that may have occurred during transport.

Note: Damage claims cannot be made during or after installation.

IMPORTANT: Please read these instructions carefully before you

begin and retain for future reference. These instructions have

been prepared for your guidance, you must exercise due care at

all times.

We do not accept responsibility for any problems that may occur

through incorrect installation.

Dimensions

Tools required

The installation must comply with all plumbing codes including

local

codes and be installed by a licensed plumbing contractor.

Install US-418ROUGH first using the instructions provided with it.

IMPORTANT! Before installing a new faucet it is essential that the

supply pipes are thoroughly flushed in order to remove any

remaining debris, solder or other impurities. Failure to carry out this

simple procedure can cause problems or damage to the working of

the faucet.

Installing shut-off valves on incoming supply lines is recommended

for ease of maintenance.

Turn off the main water supply before connecting to any existing

pipework or doing any maintenance.

WARNING! Please check for any hidden pipes and cables, electric

or otherwise,before drilling holes in a wall or floor.

PLASTIC

PLATE

SCREWS x4

(Retain for

future use)

VALVE

BODY

COVER

PLATE

VALVE

BODY

UPSTAND

PIPE

34”

LENGTH

SCREWS x4

(Retained)

HANDSET

FAUCET

BODY

HOSE

NUT

HOSE

CONE

IMPORTANT:

For valve body installation see installation instructions for

US-418ROUGH before following the trim installation detailed

below.

lWith the main water supply turned o.

lRemove the 4 screws securing the plastic plate.

lRemove the plastic plate with the two plugs.

lKeep the 4 screws in a safe place for future

use.

Installation

lSlide the cover plate up the upstand pipe, taking care not to mark

the surface.

lTurn the body so that the spout is facing the correct direction.

lPush the faucet body down into the valve body.

lThis is a pre-tested product so care should be taken not to put

undue stress on the tails as this could damage the seals within the

body of the faucet.

lFix the faucet body onto the valve body using the 4 screws.

lAt this point the water supply can be switched on and the unit

tested for leaks.

lExtra care and time should be taken to check for leaks as the

valve body will be concealed once installation is complete.

lPosition the cover plate and use a suitable sealant to seal.

lConnect the hose cone to the handshower.

lConnect the hose nut to the faucet body.

ATTENTION: Check all new connections for leaks.

lOnce satised there are no leaks, switch on the heating system.

Installation

Installation

WASHER

HANDLE

RETAINING

NUT

BRASS

SLEEVE

SCREW

GASKET

SLEEVE

DIVERTOR

CARTRIDGE

HEXAGONAL

KEY

WASHER

HANDLE

RETAINING

NUT

BRASS

SLEEVE

SCREW

COUPLING

GASKET

STOP

HEXAGONAL

KEY

THERMOSTATIC

CARTRIDGE

Cleaning the diverter cartridge

lThe diverter cartridge should give trouble-free service,

however servicing is a straightforward process.

To remove the diverter cartridge:

lWith the water supply turned o, unscrew the pin on the handle

taking care not to mark the finish.

lUsing a hexagonal key loosen the set screw but do not remove.

lRemove the handle and gasket.

lUndo the retaining nut and pull the diverter cartridge out with the

sleeve and brass sleeve attached.

lWash the diverter cartridge with clean running water, dry and

lightly grease the seal, (only use silicone grease).

lReplace the diverter cartridge followed by the retaining nut, gasket

and handle.

Thermostatic cartridge

lThe thermo cartridge should give trouble-free service, however

servicing is a straightforward process.

To remove the thermostatic cartridge:

lWith the water supply turned o, unscrew the pin on the handle

taking care not to mark the finish.

lUsing a hexagonal key loosen the set screw but do not remove.

lRemove the handle and gasket.

lRemove the coupling, (take note of the orientation of the coupling).

lUndo the retaining nut and pull the thermo cartridge out with the

brass sleeve attached.

lWash the thermostatic cartridge with clean running water and

make sure that any trapped debris has been removed.

lDry and lightly grease the seals, (only use silicone grease), and

replace the thermo cartridge.

lTo re-assemble, reverse the sequence above taking care to replace

the coupling in the same orientation before removal.

Maintenance

Thermo cartridge - Set temperature to desired maximum

To set the thermo cartridge:

lWith the water supply turned o, unscrew the pin on the handle

taking care not to mark the finish.

lUsing a hexagonal key loosen the set screw but do not remove.

lRemove the handle and gasket.

lRemove the stop ring, (take note of the orientation of the stop ring).

lAdjust the temperature of the thermo cartridge to desired maximum.

lTo re-assemble, reverse the sequence above taking care to replace

the stop ring in the same orientation before removal.

Vertical marking

HANDLE

STOP

RING

STOP

RING

HEXAGONAL

KEY

THERMOSTATIC

CARTRIDGE

Issue date: 18112019

5 Cleaning Instructions

Rinse away any traces of soap and gently dry with a clean, soft cloth after each use. Rinse completely with water and dry any overspray. This

will maintain the finish and avoid water spotting.

To remove mineral deposits, use a 50/50 solution of white vinegar and water. Do not allow the solution to soak on the product.

Simichrome Polish® contains a protective film to enhance maintenance and is helpful in preventing water spot buildup. Follow instructions

to ensure optimum results.

Never use an abrasive material such as a brush or scouring pad to clean the surface. The use of abrasive cleaners, cleansers or disinfectants

will alter the surface finish and void the warranty.

Do not allow certain materials such as toothpaste, cologne, shaving cream, nail polish remover, vinegar, wine, drain and glass cleaners to

remain on the surface. Prolonged contact will alter surface finishes and void the warranty.

We DO NOT recommend using any household cleaners as many can cause damage to the finish.

Please see the website for care instructions for specific finishes.

Warranty - This Crosswater London product is covered by a limited lifetime warranty. For full details, terms and conditions please visit our website.

For further information contact:Crosswater London, 393 Fortune Blvd., Milford, MA 01757

Toll free number: 844-XWATER-1 (844-992-8371) tel: 508-381-0433 fax: 508-381-6068

www.crosswaterlondon.com

email: technical@crosswaterlondon.com

Inhaltsverzeichnis

Andere Crosswater Sanitärprodukte Handbücher

Crosswater

Crosswater US-BTW0201 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF0613 Bedienungsanleitung

Crosswater

Crosswater LIBRA LB6117C Series Bedienungsanleitung

Crosswater

Crosswater US-AL7005CW Bedienungsanleitung

Crosswater

Crosswater PRO125DNJ Bedienungsanleitung

Crosswater

Crosswater 28-16-T Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL422 Bedienungsanleitung

Crosswater

Crosswater ATOLL SQUARE EXPOSED THERMO SHOWER VALVE... Bedienungsanleitung

Crosswater

Crosswater Darby 15-15P-T Bedienungsanleitung

Crosswater

Crosswater Darby 15-16-T Bedienungsanleitung

Crosswater

Crosswater Arcade US-ARC14 Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF135 Bedienungsanleitung

Crosswater

Crosswater US-BSW0101 Bedienungsanleitung

Crosswater

Crosswater US-ARC953 Bedienungsanleitung

Crosswater

Crosswater Belgravia US-BL002 Bedienungsanleitung

Crosswater

Crosswater Berea 11-19-T Bedienungsanleitung

Crosswater

Crosswater Waldorf US-WF422175 Bedienungsanleitung

Crosswater

Crosswater Leyden 14X-03-T Bedienungsanleitung

Crosswater

Crosswater Fenmore 28-20-T Bedienungsanleitung

Crosswater

Crosswater Taos Deck-mount Tub Faucet with Handshower Trim... Bedienungsanleitung

Crosswater

Crosswater 11-04 Bedienungsanleitung

Crosswater

Crosswater Leyden 14-05 Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Crosswater

Crosswater Wisp US-WP418 Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema