Lippert Curt 13496 Bedienungsanleitung

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13496-INS-RA •12/13/2021 •ECN9115 •PAGE 1

Product Registration and Warranty

CURT stands behind our products with industry-leading warranties. To get copies of the product

warranties, register your purchase or provide feedback, visit: warranty.curtgroup.com/surveys

Weight Carrying Capacity

Gross trailer weight (GTW) 2,000 lbs.

Tongue weight (TW) 200 lbs.

INSTALLATION MANUAL 13496

Tools Required

Ratchet Fishwire, 1/2"

(includes 4 qty)

Socket, 3/4" Tape measure

6" Socket extension Die grinder

Torx bit, T-10, T-25 Tape

Torque wrench Reciprocating saw/

Rotary tool

* For a tools reference guide visit

curtmfg.com/trailer-hitch-installation

Level of Difficulty

Moderate

Installation difficulty levels are based on time

and effort involved and may vary depending on

the installer level of expertise, condition of the

vehicle and proper tools and equipment.

WARNING

Never exceed the vehicle manufacturer's recommended towing capacity.

SAFETY INSTRUCTIONS

Safety glasses should be worn at all times while installing this product.

NOTICE

Visit www.curtmfg.com for a full-color copy of this

instruction manual, as well as helpful videos, guides and much more!

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

This installation requires:

• Part removal and trimming of the underbody panel

Periodic inspection of the trailer hitch should be performed to ensure all

mounting hardware remains tight and structural components are secure.

To help prevent damage to the product or vehicle, refer to the specified

torque specifications when securing hardware during the installation process.

CAUTION

Use caution when trimming lower fascia

Parts List

Item Qty Description

1 4 Carriage bolt, 1/2-13" UNC,

1-1/4", grade 8

2 4 Serrated flange nut,

1/2"-13 UNC, grade 8

3 4 Square hole spacer,

1/4" x 1" x 3"

Product Photo

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13496-INS-RA •12/13/2021 •ECN9115 •PAGE 2

ASSEMBLY

HOLE ENLARGEMENT

Attach the ﬁshwire to

the carriage bolt and

slide the spacer onto

the ﬁshwire.

Push the bolt through

the hole followed by

the spacer, as shown.

Pull the bolt back into

position, protruding

from the frame.

REVERSE PULL FISHWIRE TECHNIQUE

Insert coiled end of ﬁshwire tool through hitch

mounting hole in vehicle frame rail and out the

access hole. Pass coiled end of ﬁshwire

through spacer and thread bolt into

coil. Kink wire to keep spacer

seperate from bolt as shown.

Pull ﬁshwire, spacer and

bolt through frame and

out mounting hole. Use

ﬁshwire to guide hitch during mounting and

prevent loss of bolt or spacer inside frame rail.

MOUNTING

HOLE

ACCESS

HOLE

FISHWIRE TECHNIQUE

Parts List

Item Qty Description

1 4 Carriage bolt, 1/2-13" UNC,

1-1/4", grade 8

2 4 Serrated flange nut,

1/2"-13 UNC, grade 8

3 4 Square hole spacer,

1/4" x 1" x 3"

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13496-INS-RA •12/13/2021 •ECN9115 •PAGE 3

Step 1

From behind the driver-side wheel well,

remove the screw using a T-25 torx bit.

Remove the retaining screw using a T-10 torx

bit from the retaining clip from the lower

fascia. Finish removing the retaining clip that

connects the lower fascia to the trunk pan.

Repeat on the other side of the vehicle.

Note: To assist in the removal of the retaining

clip, compress the tabs that are accessible

from behind / above the lower fascia.

Step 2

Use a utility knife to remove the

underbody coating from the holes in

the frame to allow the hardware to pass

through the holes within the frame.

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13496-INS-RA •12/13/2021 •ECN9115 •PAGE 4

Step 3

Fishwire the carriage bolt (#1) and square hole

spacer (#3) into each frame rail through an

access hole in each frame rail to the forward-

most mounting hole. The access hole may

need to have the coating removed and / or be

enlarged slightly to allow the hardware to pass

through. Reverse fishwire the hardware through

the access hole into the frame rail.

Step 4

Trim the lower fascia using

the trim diagram as a reference.

3-1/4"

3-1/2"

CURTMFG.COM •PRODUCT SUPPORT: 877.287.8634 •13496-INS-RA •12/13/2021 •ECN9115 •PAGE 5

Step 6

Torque all 1/2" hardware to 110 ft-lbs.

Step 7

Reinstall both retaining clips and screws in

lower fascia that were removed in Step 1.

Step 5

Raise the hitch into position. Pull downward

and rearward on the lower fascia to allow

room for the hitch to pass between the fascia

panel and trunk pan. Make sure to guide

the fishwire through the holes in the hitch.

Remove fishwire and secure the hitch

using the supplied 1/2" flange nuts (#2).

Note: Be careful not to

push the hardware into frame.

TOWING BASICS & SAFETY INFORMATION

For information on safely towing your trailer, visit curtmfg.com/understanding-towing.

Final Installed Image

Andere Lippert Autozubehör Handbücher

Lippert

Lippert LUVERNE 401720 Bedienungsanleitung

Lippert

Lippert OneControl Bedienungsanleitung

Lippert

Lippert ARIES 2500207 Bedienungsanleitung

Lippert

Lippert Power Step 2.0 Bedienungsanleitung

Lippert

Lippert Kwikee Step Well Cover Bedienungsanleitung

Lippert

Lippert SolidStep 4.0 Bedienungsanleitung

Lippert

Lippert Curt 60654 Bedienungsanleitung

Lippert

Lippert LatchXtend RV Door Handle Bedienungsanleitung

Lippert

Lippert Curt 18110 Bedienungsanleitung

Lippert

Lippert JT's Strong Arm Montageanleitung

Lippert

Lippert Vela Pop Up Gebrauchs- und Pflegehandbuch

Lippert

Lippert RV Bedienungsanleitung

Lippert

Lippert Stargazer Spirit XTR Skylight Bedienungsanleitung

Lippert

Lippert Sway Command 1.5 Bedienungsanleitung

Lippert

Lippert Tire Linc Montageanleitung

Lippert

Lippert 45940-85 Bedienungsanleitung

Lippert

Lippert Thin Shade 806621 Montageanleitung

Lippert

Lippert Power Steps 2.0 Bedienungsanleitung

Lippert

Lippert FLYSCREEN N Series Bedienungsanleitung

Lippert

Lippert Level-up Bedienungsanleitung

Lippert

Lippert ARIES S224050 Bedienungsanleitung

Lippert

Lippert CURT 45937 Bedienungsanleitung

Lippert

Lippert Vela Pop Up Bedienungsanleitung

Lippert

Lippert 2021000090 Montageanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung