Mazda 0000-8G-K01 Bedienungsanleitung

AS 090-M11356cmc1105RevA

Page 1 of 4

Genuine Accessories

Installation Instructions

Part Number

0000-8G-K01

Applicable Models:

2004 Mazda RX8 Base

Package Contents

Front Mask

U-Nut (Qty. 8)

Tools Required

Stubby Phillips

Screwdriver

Hood Cover (Qty. 1)

Snap Head Screw (Qty. 8) Front End Cover (Qty. 1)

0Before Installation

A. Area to be covered by mask must be clean. It is recommended that you wash and wax vehicle prior to installation.

B. Both vehicle and mask must be completely dry prior to installation. If moisture under mask is allowed to dry on

vehicle, paint may cloud.

C. Any repainted surfaces in contact with mask must be allowed to cure completely. Consult paint manufacturer or

repair facility if you are not sure.

1Install Hood Cover

A. With hood open, stretch hood cover (A)

onto hood, pulling each side one or two

inches at a time, until corners fit snugly.

Install hooks on ends of straps (B) into

corresponding holes in hood. Pull

evenly on ends of adjustable straps (B)

until tight. Secure loose ends in elastic

loops.

Washer (Qty. 8)

Page 2 of 4

AS 090-M11356cmc1105RevA

2Remove wheel well fasteners

A. Using stubby phillips screwdriver, remove five plastic

fasteners along front edge of both front wheel wells.

A. In both front wheel wells, lift wheel well liner to reveal holes.

B. Slip u-nuts (C) over top two and bottom two holes in metal edge,

making sure that holes are aligned.

C. Release liner to its original position. Using a stubby phillips

screwdriver, install washer (D) and snap head screws (E) into top

two and bottom two holes in each wheel well. Reinstall

original fastener into unoccupied middle hole.

3Install wheel well hardware

4Install upper attachments

A. With hood open, lay front end cover over

front of vehicle. On both sides of vehicle,

slide pockets (F) over front corners

of fenders. Care should be taken

to prevent ripping of pockets (F).

B. Attach clips (G) to edge of fender

rails.

C. On both sides of vehicle, insert

pads (H) in slot under headlights.

D. Attach clips (J) to back inside

edge of metal at center of vehicle

under hood.

GFG

Page 3 of 4

AS 090-M11356cmc1105RevA

6Install bottom attachments

7Post Installation Inspection

A. Close hood and check alignment between hood

cover and front end cover along seam (between

fender and hood). If adjustment is necessary, adjust

the hood cover by adjusting the hood cover straps.

Refer to step 1.

B. If mask should flap due to high speed or wind

conditions, adjust or remove mask completely.

8Care and Cleaning

A. Always remove mask before washing vehicle.

B. Hand clean mask using mild soap, rinse thoroughly with

clean water and line dry completely. Do not machine dry!

C. Use Mazda Vinyl/Leather Protectant (or equivalent) to

preserve color and finish.

D. WARNING: Running up on curb will damage this product.

Manufacturer will not be responsible for damage to product

due to accident or misuse.

Place in vehicle glove compartment.

A. Insert pads (L) into slot located between edge of front facia and top edge of grille area. Attach clips (M) to back edge of facia in

fog light area. Attach clips (N) to underside edge of bumper facia. Insert velcro loop (O) into nearby hole in grille area and

attach to velcro hook (P) located at underside edge of bumper facia.

Install wheel well

attachments

A. Press snaps (K) onto snap head

screws (E) in both front wheel wells.

MLLL

Andere Mazda Autozubehör Handbücher

Mazda

Mazda PROTEGE 5 Bedienungsanleitung

Mazda

Mazda 0000 81 L25 Bedienungsanleitung

Mazda

Mazda 0000-8G-L12 Bedienungsanleitung

Mazda

Mazda 0000-8P-R04 Bedienungsanleitung

Mazda

Mazda 0000-8C-Z02 Bedienungsanleitung

Mazda

Mazda A2DP Bedienungsanleitung

Mazda

Mazda 6 GJ 2.2 D 2012 Bedienungsanleitung

Mazda

Mazda KPF1 V3 460 Leitfaden

Mazda

Mazda 0000 8C Z01 Bedienungsanleitung

Mazda

Mazda 0000-8E-R10 Bedienungsanleitung

Mazda

Mazda 0000-8L-L2 Bedienungsanleitung

Mazda

Mazda 0000-8L-R02 Bedienungsanleitung

Mazda

Mazda CX-9 Bedienungsanleitung

Mazda

Mazda 0000-8E-G01 Bedienungsanleitung

Mazda

Mazda 0000-8G-K05 Bedienungsanleitung

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda GS2A -V1-132 Bedienungsanleitung

Mazda

Mazda 0000-8C-Z05 Bedienungsanleitung

Mazda

Mazda 2005 Miata MX-5 Bedienungsanleitung

Mazda

Mazda DN4J-V7-110 Bedienungsanleitung

Mazda

Mazda KA0G V1 370 Bedienungsanleitung

Mazda

Mazda 0000-8E-N31 Bedienungsanleitung

Mazda

Mazda 0000-8C-G21A Bedienungsanleitung

Mazda

Mazda CX-3 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung