Prince Castle Burger King DHB-BK41 Bedienungsanleitung

BISC

SAUS

BACN

ENTER

BKFT

REG

TRANSFER

EGGS

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

Product Holding Bin

DHB-BK41/43

Operation

Manual

355 East Kehoe Blvd. • Carol Stream, IL 60188

Phone: 630-462-8800 • Toll Free: 1-800-PCASTLE

Fax: 630-462-1460 • www.princecastle.com

LIMITED WARRANTY

This product is warranted to be free from defects in material and/or work-

manship for a period of three (3) years from date of original installation, not

to exceed 36 months from date of shipment from our factory.

Any component which proves to be faulty in material and/or workmanship

will be replaced or repaired (at the option of Prince Castle, Inc.) without

cost to the customer for parts or labor. This warranty covers on location

service (i.e. trip charges and/or mileage). Travel mileage is limited to 100

miles (200 kilometers-International) round trip (one trip warranty) from an

authorized service agency or its sub-service agency.

This warranty is subject to the following exceptions/conditions:

• Use of any non-genuine Prince Castle parts voids this warranty.

• All labor shall be performed during regular work hours. Overtime premi-

um will be charged to the buyer.

• Damage caused by carelessness, neglect, and/or abuse (e.g., dropping,

tampering or altering parts, equipment damaged in shipment, by fire,

flood or an act of God) is not covered under this warranty.

TABLE OF CONTENTS

Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4–9

CastleNet Communications Network . . . . . . . . . . . . . . .10

Factory Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

LED Timers (tri-color)

(qty. 8, each side)

Pan Buttons

(qty. 8)

Power On/Off Switch

Temperature Control

Panel

PRINCE CASTLE

LOGO Button

Pan & Pan Cover

Button Bar

Transfer Button

Lower Pan Displays

(qty. 4, each side)

Upper Pan Displays

(qty. 4, each side)

MENU/ENTER

Button

BKFT (Breakfast)

LED

UP and DOWN

Arrow Buttons REG (Regular Menu)

LED

Product Identification

IN OUT

EXTERNAL

Product Holding Bin

DHB-BK41/43

Installation

Safety Information

A. Remove the unit from the carton and inspect for signs of damage. If

there is damage to the unit:

• notify the carrier within 24 hours of delivery

• save carton and packaging materials for inspection purposes

• contact your local dealer, or if purchased directly, the Prince

Castle Sales Department at 800-722-7853 or 1-630-462-8800 to

arrange for a replacement unit.

NOTE: When installing this unit, the ambient temperature at the mount-

ing site should not exceed 100°F.

B. Place the bin on a counter and seal the base to the counter with

food-approved sealant.

C. Plug the power cord into the bin and connect the plug into the prop-

er electrical outlet (15 amp, 120 Volt). All connections must be in

accordance with local electrical codes and any other applicable

codes.

NOTE: The electrical receptacle should be a dedicated outlet. No other

equipment should be operating on the line (refrigerators, fryers, etc.).

D. If used, plug the Prince Castle Retro Bun Steamer BK-RSTMC timer

data cable into the blue plug jack (External) located on the rear of the

Prince Castle holding bin. If cable from timer is too short, use Prince

Castle Extender Cable Kit, P/N PC-COMEXT.

E. Install the racks, pans and pan covers into the cavities.

F. Turn the power switch to ON. Allow 30 minutes for warm-up.

Prince Castle reserves the right to change specifications and product design without notice. Such revisions do not

entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased

equipment.

WARNING

Indicates information important to the proper opera-

tion of the unit. Failure to observe may result in dam-

age to the equipment and/or severe bodily injury or

death.

CAUTION

Indicates information important to the operation of

the unit. Failure to observe may result in damage to

the equipment.

White Plug Jack

(in from another unit)

Power Cord Inlet

Blue Plug Jack

(Plug BK-RSTMC

Retro Bun Steamer

timer data cable into

here)

Black Plug Jack

(out to another unit)

Rear of PHU

NOTE: If the unit is to networked with other Prince Castle units, a

Retro Bun Timer may be connected to any one bin in the chain. Refer

to CASTLENET COMMUNICATIONS NETWORK in this manual.

IN OUT

EXTERNAL

IN OUT

EXTERNAL

IN OUT

EXTERNAL

RETRO

BUN

TIMER

BIN 1 BIN 2 BIN 3

Product Holding Bin

DHB-BK41/43

Operation

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

1Turn power On/Off switch to ON position.

Allow 30 minutes for

heaters to reach operating

temperature. The

Temperature Display will

show temperature as unit

warms up to the operating

temperature.

Power On/Off Switch

Load pan covers (if used) onto pan racks and

insert racks into the unit.

EGGS

ENTER

BKFT

REG

Press all PAN Buttons

The PAN DISPLAYS will show the

assigned product name.

If no product is assigned, the display

will be dim and show “----”. Pressing

the PAN button will not activate the

timer if “----” is displayed. Pressing

PAN button when product name is

displayed will start timing cycle.

BKFT (Breakfast) or

REG (Regular Menu)

will be lit depending on

pre-programmed menu.

EGGS

ENTER

BKFT

REG

LED Timing Status When LED is steady

RED, load product

and press the PAN

Button.

(steady) = Ready for product

(flashing) = Discard product

(steady) = Oldest product, use first

(flashing) = Cook more product

(steady) = Newer product, use green first

(flashing) = Cook more product

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

If only one pan is active for a

product, the LED will turn from

RED to GREEN.

If no other pan is active for a

product, the LED for the first pan

loaded will turn from RED to

GREEN.

The LED for the 2nd pan (3rd

pan, etc.) loaded will turn from

RED to YELLOW.

An LED timer can be stopped

(cancelled) at any time by press-

ing and releasing the

corresponding PAN Button.

LED Timers

RED

GREEN

YELLOW

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

Discard product

Cook more product

When any of the timer LED’s flash, cook more product or

remove and discard product as indicated.

EGGS

BACN

SAUS

BACN

ENTER

TRANSFER

Product, along with any remaining time, can be

transferred from one cavity to another as follows:

A. Press and release the TRANSFER

Button on the timer bar of the product

to be moved. Displays for all pans

available for transfer will be brightly lit.

All others will be dimly lit.

B. Press and release the PAN

button of the product to be

moved.

C. Press and release the

TRANSFER button on the

bar where the product will

be moved. All available pan

locations on the bar will be

brightly lit.

D. Press and release the PAN button

for the new location. The new loca-

tion will finish timing the product.

When the transferred pan time

expires, the location will revert back

to the original menu settings.

WARNING

Hot surfaces.

NOTE: If product transfer is not completed within a pre-programmed

transfer time, the transfer will be cancelled. See your Manager.

GREEN

Flashing

YELLOW

Flashing

RED

Flashing

Product Holding Bin

DHB-BK41/43

A225

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Operation (continued)

Cleaning

PRESET LOADED

ENTER

BKFT

REG

TRANSFER

PRESET LOADEDPRESET LOADEDPRESET LOADED

To shut down the unit, turn the power On/Off switch to OFF.

NOTE: To load preset times/menus:

A. Turn power switch to OFF.

B. Press and hold both the UP and DOWN Buttons.

C. Turn power switch ON.

D. When the four right-most displays show PRESET LOADED, release the buttons

Setting Temperature

1. Turn the unit off and unplug the power cord from the electrical

receptacle.

2. Remove the pan covers and pan racks. Wipe all parts and unit

with a damp cloth. DO NOT use a green scotch bright pad cleaner,

ice or water.

WARNING

Before performing any maintenance, turn the power switch to the OFF

position and unplug the power cord from the electrical receptacle.

CAUTION

This unit is not watertight. Do not clean with a water jet/jet spray.

Do not immerse the unit in water.

The unit has four shelves, each with an upper and lower heater (eight heaters total).

The factory pre-set for the upper heaters is 225°F.

The factory pre-set for the lower heaters is 195°F.

Each upper heater has a programmable range of 150° - 275°F.

Each lower heater has a programmable range of 150° - 225°F.

Use the control below and the following steps to set the setpoint temperatures for each heater.

UPPER SHELF LED

This LED will be lit to indicate

upper shelf is selected

UP/DOWN ARROW BUTTONS

Used with other buttons to scroll

through heater and temperature

selections

PRINCE CASTLE LOGO BUTTON

Press to enter

temperature selections

TEMPERATURE DISPLAY

A, b, C or d Shelf

NOTE: The unit is preset to display temperature in

Fahrenheit. To display in Celsius, press and hold

the DOWN Arrow button immediately after turning

on the power switch. To switch back to Fahrenheit,

press and hold the UP Arrow button after turning

on the power switch.

PROG LED

This LED will be lit to indicate

unit is in Program Mode

LOWER SHELF & LED

This LED will be lit to indicate

lower shelf is selected

ACTUAL TEMP BUTTON & LED

Press to display actual temperature for the

selected heater. LED will be lit when actual tem-

perature is displayed.

SETPOINT BUTTON & LED

Press to display setpoint temperature of a

selected heater. LED will be lit when setpoint

temperature is displayed.

NOTE: To reset all times and temperatures to the factory settings, turn the unit off, then press and hold the UP and DOWN arrow buttons

simultaneously while turning the unit back on. A “P” will appear in the display and all times and temperatures will be reset to original factory settings.

Product Holding Bin

DHB-BK41/43

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

A220

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

A225

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

A225

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Setting Temperature (continued)

Press the UP or DOWN Arrow Buttons until the desired shelf

(A, b, C or d) LED and upper (U) or lower (L) heater is selected.

2Press and hold the SETPOINT Button and the Prince Castle

Logo Button for 5 seconds. The Program LED will light.

Calibrating Heaters

Use the following steps to calibrate

the individual heaters.

NOTE: Allow sufficient amount of

time for temperatures to stabilize

before starting calibration.

Press the UP or DOWN Arrow

Buttons until the desired shelf LED

and upper (U) or lower (L) heater is

selected.

Take a temperature reading within the shelf near the center of

the heater surface.

Use a standalone temperature meter (not supplied).

Press the UP or DOWN Arrow Buttons until the desired

setpoint temperature is displayed

A2:30

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

A225

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Press and hold the PRINCE CASTLE

LOGO and ACTUAL Buttons for 5

seconds. The semi-colon (:) LED

indicator will light. The temp dis-

played is the actual heater tempera-

ture sensed by the controller.

A2:20

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Press the UP or DOWN Arrow

Buttons until the temperature

displayed matches the reading

obtained in Step 2.

Press the PRINCE CASTLE

LOGO Button to save the

temperature value and exit the

Calibration Mode.

Press the Prince Castle Logo Button to save the new setpoint

value. Repeat steps 2—5 to change the setpoint for any other

heater.

WARNING

Hot surfaces. Use

caution when taking

temperature readings

within the shelf

A220

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

A2:30

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

To clear any offset

readings, press the

SETPOINT Button.

A220

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Selecting Breakfast and Regular Menus

MNU1

⇑

ENTER

BKFT

REG

⇑

PROG

WBUN

ENTER

BKFT

REG

SFER

Programming the Menus

PROG

TRANSFER

MNU1

⇑

ENTER

⇑

RANSFER

There are six menus available:

BKFT LED ON = Menu1 or Menu6

REG LED ON = Regular2, Regular3, Regular4, or Regular5

Press and hold the MENU/ENTER button, then use the UP or

DOWN Arrow button to scroll through the 6 menus.

Press and hold the MENU/ENTER button, the display next to

the MENU/ENTER button will show the menu choices. Use

the UP or DOWN Arrow button to scroll through the 6 menus.

Release the MENU/ENTER button when the desired menu is

displayed.

When the MENU/ENTER button is released, all displays will

again show PROG

Press and hold the PRINCE CASTLE LOGO button

(on the button bar) until all the displays show PROG

and the BUN TRAY buttons LED’s all glow red.

A. Press the PAN button next to the display to be changed.

The LED will change from red to yellow and the display will

change from PROG to the assigned menu item.

When scrolling, menu numbers appears in this display.

MNU1

⇑

ENTER

BKF

REG

⇑

FER

When the desired menu is displayed, release the

MENU/ENTER button. The food products for the menu will be

displayed in the upper and lower BUN TRAY displays.

When timers for a different menu are still active,

those BKFT or REG LED’s will flash until they are all cancelled.

----

PROG

A. Repeat Steps 2 & 3 as required.

B. Press the PRINCE CASTLE LOGO button to exit the

Programming Mode and return to the Run Mode.

NOTE: Up to six items (one for each menu) may be programmed

for each tray button. A tray may be set as “not used” by

assigning “

----

” as its product.

PROG

ENTER

FER

PROG

SBUN

ENTER

BKFT

REG

FER

B. Press the UP or DOWN Arrow buttons to scroll to the desired menu

item.

C. Press the MENU/ENTER button to save the selection. All displays

will show PROG.

Product Holding Bin

DHB-BK41/43

TIME

PROD

SET

ENTER

BKFT

REG

TRANSFER

⇑

A. The SET PRODUCT TIME menu is used to change the Hold & Cook-More times.

B. Press and hold the PRINCE CASTLE LOGO button, then immediately press and hold the MENU/ENTER button until the display shows one

of the programming menus.

C. Use the UP or DOWN Arrow button to scroll to the SET PROD TIME ⇑ ⇓ menu.

NOTE: Hold Times are specified by Burger King Corporation. Prince Castle does not endorse changing hold times unless instructed by

Burger King Corporation.

PRINCE CASTLE LOGO Button

MENU/ENTER Button

Product Holding Bin

DHB-BK41/43

:07

EGGS

COOK

ENTER

TRANSFER

⇑

2:00

EGGS

HOLD

ENTER

TRANSFER

⇑

TIME

PROD

SET

ENTER

TRANSFER

⇑

Changing the Hold & Cook-More Times

TIME

EGGS

SET

ENTER

TRANSFER

⇑

A. Press and release the MENU/ENTER button to enter the

Set Product Time menu. The display will show, for example,

SET EGGS TIME ⇑ ⇓ ..

A. The display now shows the current hold time.

A. The display will show SET PROD TIME ⇑ ⇓ ..Repeat Steps 2 – 4

for any other product.

B. Press and release the PRINCE CASTLE LOGO button at any

time to exit the Programming Mode and return to the Run Mode.

NOTE: If the MENU/ENTER button has not been pressed to save any

changes, the program will revert to the original values.

A. The display will now show current Cook-More time..Use the

UP or DOWN Arrow button to scroll to the desired cook -

more time.

B. Use the UP or DOWN Arrow button to scroll to the desired

hold time. When the desired hold time is displayed, press

the MENU/ENTER button to save the desired hold time.

NOTE: Hold time cannot be reduced to less than the Cook-More

time plus one minute.

NOTE: Cook-More time cannot be increased to more than the

Hold time minus one minute.

2:10

EGGS

HOLD

ENTER

TRANSFER

⇑

B. When the desired cook-more time is displayed, press the

MENU/ENTER Button to save it.

:10

EGGS

COOK

ENTER

TRANSFER

⇑

NOTE: Holding the UP or DOWN Arrow Buttons for longer than 2

seconds will cause the product list to automatically scroll up or down.

B. Use the UP or DOWN Arrow button to scroll through the list

of products. When the desired product is displayed, press

the MENU/ENTER button to select it.

Refer to the Product Menu Details on page 8 for a list of

products and their corresponding display names.

Product Holding Bin

DHB-BK41/43

Changing Product Names

WXP1

PROD

SEL

ENTER

BKFT

REG

TRANSFER

⇑

NAME

PROD

EDIT

ENTER

TRANSFER

⇑

NAME

PROD

EDIT

ENTER

BKFT

REG

TRANSFER

⇑

EXP1

PROD

SEL

ENTER

TRANSFER

⇑

A. The EDIT PRODUCT NAME menu is used to change a default product name to one of your own choosing.

B. Press and hold the PRINCE CASTLE LOGO button, then immediately press and hold the MENU/ENTER button until the display shows one

of the programming menus.

C. Use the UP or DOWN Arrow button to scroll to the EDIT PROD NAME ⇑ ⇓ Menu.

NOTE: The default names available for editing are listed on page 8.

A. Press and release the MENU/ENTER button to enter the

Edit Product Name menu.

The display will read SEL PROD XXXX ⇑ ⇓ ..

B. Use the UP or DOWN Arrow button to scroll through the list of

products.

C. When the desired product is displayed, press the

MENU/ENTER button to select it. The first letter (in this case,

the EE) will start blinking.

A. The display will show EDIT PROD NAME ⇑ ⇓ . Repeat Steps

2–4 for any other product.

B. Press and release the PRINCE CASTLE LOGO button at

any time to exit the Programming Mode and return to the

Run Mode.

NOTE: If the MENU/ENTER button has not been pressed to save

any changes, the program will revert to the original names.

2A. To change the blinking E, use the UP or DOWN Arrow button

to scroll to the desired letter/number/symbol.

B. When the desired selection is displayed, press the PAN

button (to the left or right of the selected display) to move

to the next digit.

C. Repeat for all digits.

NOTE: Holding the UP or DOWN Arrow Buttons for longer than 2

seconds will cause the selected digit to automatically scroll up or

down.

WXP1

PROD

SEL

ENTER

TRANSFER

⇑

When all four digits have been changed, press the MENU/ENTER

button to save the new name.

PRINCE CASTLE LOGO Button MENU/ENTER Button

GRPx

LINK

SET

ENTER

TRANSFER

ENTR

Product Holding Bin

DHB-BK41/43

Set Maximum Transfer Time

Product Linking

:20

XFR

TRANSFER

A. Press and release the MENU/ENTER Button to enter the

Set Maximum Transfer Time menu.

B. The display shows MAX XFR :20 ⇑ ⇓ . This shows a value

of 20 seconds.

Any Timer Bar (except bun holding timers) can be linked to others (see Special Programming Modes, this page). If Timer Bars are set to the same

link group, any product started in any bar of the same group will be compared to all other products in the same group, and it’s LED color will be

determined based on all timers in the group with the same product (not just with all timers on it’s own Timer Bar).

Special Programming Mode

A. Press and hold the LOGO Button then immediately press and hold the MENU/ENTER Button. Hold both buttons for six seconds. The

displays will change to show the first menu – depending on model.

B. Press and release the UP and DOWN Buttons to scroll through the list of Special Modes.

:25

XFR

TRANSFER

A. To change the time, use the UP or DOWN Arrow Button to

scroll to the desired time. When the desired selection is dis-

played, press the MENU/ENTER Button to enter the selection.

B. Press and release the PRINCE CASTLE LOGO Button at any

time to exit the Programming Mode and return to the Run

Mode.

NOTE: If the MENU/ENTER Button has not been pressed to save any

changes, the program will revert to the original time.

TIME

XFR

MAX

ENTER

BKFT

REG

TRANSFER

⇑

A. The SET MAXIMUM TRANSFER TIME menu is used to set the amount of time allowed to make a product transfer from one pan to another.

B. Press and hold the PRINCE CASTLE LOGO Button, then immediately press and hold the MENU/ENTER Button until the display shows one

of the programming menus.

C. Use the UP or DOWN Arrow Button to scroll to the MAX XFR TIME ⇑ ⇓ (Set Maximum Transfer Time) Menu.

PRINCE CASTLE LOGO Button MENU/ENTER Button

TIME

XFR

MAX

ENTER

BKFT

REG

TRANSFER

⇑

PRINCE CASTLE LOGO Button MENU/ENTER Button

A. When the displays show SET LINK GRPx ⇑ ⇓ ENTR , the X indicates the currently assigned Link Group. Press and release the MENU/ENTER

Button to set the Link Group mode.

B. The link group number (X) will flash. Press and release the UP and DOWN Buttons to change the group number. The maximum number

allowed is 3, and the minimum is 0. When a timer bar is assigned to Link Group 0, it is isolated and not associated with any other timer bar

(linking is disabled).

C. When the desired link group is displayed, press and release the MENU/ENTER Button to save it. The program will revert to Set Link Group Mode.

2Set Link Group

Product Holding Bin

DHB-BK41/43

CastleNet®Communications Network

The Prince Castle DHB-BK Bins and Retro Bun Timer and New Bun

Cabinet Timers can be inter-connected to form the CastleNet®

Communication Network. The network can be used for data transfer

between bins and timers for menu updates or to transfer product hold

time from bin-to-bin. A PDA (or similar device) or a notebook with Prince

Castle MenuView®software is used to connect to the network and enter

the desired changes.

Each bin is supplied with a standard 25' cable and allows units to be

“daisy-chained” together to form the network. If cable is too short, use

Prince Castle Extender Cable Kit, P/N PC-COMEXT.

The factory default address for Main bins and timers is address 1.

The factory default address for Specialty bins and timers is address 2.

If a third bin is used, the address must be set at 3.

The factory default address for the Retro Bun Timer is bunF.

IN OUT

EXTERNAL

IN OUT

EXTERNAL

IN OUT

EXTERNAL

RETRO

BUN

TIMER

BIN 1 BIN 2 BIN 3

Telephone jack plugs are located on the back of the unit.

Connect the units using the cables provided as shown here.

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

REG

BKFT

ENTER

BKFT

REG

TRANSFER

U225

Bin 1 Bin 2 Bin 3

Bin 2 Bin 4

Bin 1 Bin 3

Bin 6

Bin 5

IMPORTANT: Each timer must have a different address.

If a location has three bins, it is recommended that the bins

and timers be set consecutively to addresses 1 through 6.

A. Turn the power switch off, wait 15 seconds. Turn the switch

to ON while pressing and holding the ACTUAL and SET-

POINT buttons. The display will show the current bin

address.

B. Continue to hold the buttons until PROG LED turns on.

prog

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

bin3

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Available addresses are:

bin1 thru bin 9, binA, binB, binC, binD, binE

and binF.

IMPORTANT: Continue to step 5 to

check the timer address. No two

timers can have the same address.

Use the UP or DOWN Arrow buttons to scroll to the desired

address. Press the PRINCE CASTLE LOGO Button to store the

new address.

EGGS

ENTER

TRANSFER

bin2

To check the timer address, press and hold the PRINCE

CASTLE LOGO button and the DOWN Arrow button.

The current timer address will be displayed in the far right timer

display.

To change the timer address, proceed to step 6.

ADDR

SET

ENTER

TRANSFER

bin2

⇑

To change the timer address, turn the unit power switch off and

wait 15 seconds. Turn the power switch back on and immedi-

ately press and hold the PRINCE CASTLE LOGO button and the

DOWN Arrow button for approximately 6 seconds or until the

display shows SET ADDR ⇑ ⇓ BIN2.

The address number will blink on/off.

ENTER

TRANSFER

bin3

⇑

Use the UP or DOWN Arrow button to scroll to the desired

address. Press the MENU/ENTER button to store the new

address and return to normal operating mode.

Available addresses are:

bin1 thru bin 9, binA, binB, binC, binD, binE and binF.

bin2

UPPER

PROG

LOWER

ACTUAL

TEMP

SET-

POINT

Example

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Prince Castle Gewerbliche Lebensmittelgeräte Handbücher

Prince Castle

Prince Castle 197-BK Series Bedienungsanleitung

Prince Castle

Prince Castle DCFT-BKNA Bedienungsanleitung

Prince Castle

Prince Castle UHCMAX Bedienungsanleitung

Prince Castle

Prince Castle DHB-BK15 Series Bedienungsanleitung

Prince Castle

Prince Castle DHB4SS-20 Series Bedienungsanleitung

Prince Castle

Prince Castle FLAME KING BROILER Bedienungsanleitung

Prince Castle

Prince Castle DHB-P1 Bedienungsanleitung

Prince Castle

Prince Castle DHB-BK Series Bedienungsanleitung

Prince Castle

Prince Castle UHC6PT-22MCD Bedienungsanleitung

Prince Castle

Prince Castle Potato Witch 913 Bedienungsanleitung

Prince Castle

Prince Castle CTS Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-32 Bedienungsanleitung

Prince Castle

Prince Castle DHB-BKF Series Benutzerhandbuch

Prince Castle

Prince Castle EHB Series Bedienungsanleitung

Prince Castle

Prince Castle EHB-CE Series Bedienungsanleitung

Prince Castle

Prince Castle Universal JIB Series Bedienungsanleitung

Prince Castle

Prince Castle CW Series Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-CK Series Bedienungsanleitung

Prince Castle

Prince Castle EHB22 Series Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-44D Bedienungsanleitung

Prince Castle

Prince Castle EHB Series Bedienungsanleitung

Prince Castle

Prince Castle EHB34-2 Series Bedienungsanleitung

Prince Castle

Prince Castle UHC Series Bedienungsanleitung

Prince Castle

Prince Castle EHB Series Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch