Prince Castle EHB22 Series Bedienungsanleitung

Extended Holding Bin

General Market Series

Operation

Manual

Extended Holding Bin

General Market Series

LIMITED WARRANTY

This product is warranted to be free from defects in material and/or workmanship for

a period of one year from date of original installation (with the exception of racks,

pans, and covers). Any component which proves to be faulty in material and/or

workmanship will be replaced or repaired (at the option of Prince Castle, Inc.) with-

out cost to the customer for parts or labor. This warranty covers on location service

(i.e. trip charges and/or mileage). Travel mileage is limited to 100 miles (200 kilome-

ters -International) round trip (one trip warranty) from an authorized service agency

or its sub-service agency.

This warranty is subject to the following exceptions/conditions:

• Use of any non-genuine Prince Castle parts voids this warranty.

• All labor shall be performed during regular work hours. Overtime premium will

be charged to the buyer.

• Damage caused by carelessness, neglect, and/or abuse (e.g., dropping, tam-

pering or altering parts, equipment damaged in shipment, by fire, flood or an

act of God) is not covered under this warranty.

355 EAST KEHOE BLVD. ~ CAROL STREAM, IL, 60188, USA

PHONE: 630-462-8800 ~ TOLL FREE: 1-800-PCASTLE

FAX 630-462-1460 ~ WWW.PRINCECASTLE.COM

TABLE OF CONTENTS

Model Identification…………………………………………………… 2

Model Specifications…………………………………………………. 2

Safety Information……………………………………………………. 2

Configurations………………………………………………………... 3

Product Identification………………………………………………… 4

Installation…………………………………………………………….. 4

Operation……………………………………………………………… 5

Setting Product Location……………………………………………. 6

Cleaning………………………………………………………………. 6

Setting the Temperature……………………………………………. 7

Calibrating the Heaters……………………………………………... 8

Changing the Hold and Cook More Times……………………….. 9

Changing Product Names………………………………………….. 10

Changing Temperature Scale……………………………………… 11

Adjusting Alarm Volume……………………………………………. 11

Choosing a Language………………………………………………. 12

Default Menu………………………………………………………… 13

Zone Layouts………………………………………………………... 14

Dayparts……………………………………………………………... 15

Troubleshooting……………………………………………………... 16

Diagnostics…………………………………………………………… 17

Wiring Diagrams……………………………………………………... 18

Exploded Views……………………………………………………... 20

ATTENTION: Read the instructions before using the machine.

Extended Holding Bin

General Market Series

STYLE MODEL NO. WIDTH (mm) HEIGHT (mm) DEPTH (mm) WEIGHT (kgs) VOLTAGE AMPS___

2H X 2W EHB22R1-GMSXX 19.7 (500) 11.4 (290) 14.1 (358) 35 lbs. (16.0) 110-120 6.5-7.0

2H X 2W EHB22R2-GMSXX 19.7 (500) 11.4 (290) 14.1 (358) 35 lbs. (16.0) 208-240 3.8-4.4

4H X 2W EHB42R1-GMSXX 19.7 (500) 20.6 (523) 14.1 (358) 57 lbs. (26.0) 110-120 13.1-14.0

4H X 2W EHB42R2-GMSXX 19.7 (500) 20.6 (523) 14.1 (358) 57 lbs. (26.0) 208-240 7.7-8.8

2H X 4W EHB24R2-GMSXX 33.2 (843) 11.4 (290) 14.1 (358) 55 lbs. (25.0) 208-240 9.0-10.4

3H X 4W EHB34R2-GMSXX 33.2 (843) 18.1 (460) 14.1 (358) 94 lbs. (43.0) 208-240 13.6-15.7

2H X 3W EHB23R2-GMSXX 27.2 (691) 11.4 (290) 14.1 (358) 45 lbs. (20.0) 208-240 13.6-15.7

NOTE: All Model Numbers above with “R” are for double-sided units (with auxiliary timer bars).

If unit above has “R” in part number, it can be substituted for an “F” to get the single-sided version.

NOTE: Weight (kgs) is shipping weight.

NOTE: See kits starting on Page 20 for power cord type.

NOTE: 110-120V SKUs are indicated with an “R1” or “F1” for use in US/CANADA. 208-240V SKUs indicated by “R2” or “F2”.

Model Identification

Model Specifications

Safety Information

WARNING

Indicates information important to the proper operation of the unit.

Failure to observe may result in damage to the equipment and/or

severe bodily injury or death.

CAUTION

Indicates information important to the operation of the unit.

Failure to observe may result in damage to the equipment.

Important

Prince Castle reserves the right to change specifications and

product design without notice. Such revisions do not entitle

the buyer to corresponding changes, improvements,

additions or replacements for previously purchased

equipment.

EHB24R2-GMS16

Unit Name

Number of

Pans per

Shelf

Three Leer

Customer Code

Indicates Power Cord

Type

“R” for Front and

Rear Timer Bars,

“F” for Front

Only

“2” for 220V

Version, “1”

for 120V

Version

Number of

Shelves

Extended Holding Bin

General Market Series

Conguraons

EHB22

EHB42

EHB24

EHB23

EHB34

Extended Holding Bin

General Market Series

Product Identification

Installation

Remove the unit from the carton and inspect for signs of

damage. If there is damage to the unit:

• notify the carrier within 24 hours of delivery

• save carton and packaging materials for inspection pur-

poses

• contact your local dealer, or if purchased directly,

the Prince Castle Sales Department at 800-722-7853

or 1-630-462-8800 to arrange for a replacement unit.

NOTE: Plug the power cord into the proper electrical

receptacle. All electrical connections must be in accordance

with local electrical codes and any other applicable codes.

1Plug unit into a grounded

receptacle with a matching

plug configuration.

Place Holding Bin on flat surface.

Remove blue and/or white protective covering.

NOTE: When installing this unit, the ambient temperature

at the mounting site should not exceed 100°F (38°C)

Breakfast LED

Regular LED

Enter Button

LOWER PAN Display

UP/DOWN ARROWS

UPPER PAN Display

PRINCE CASTLE

LOGO Button PAN ARROW Buttons

(Start/Stop Timers)

LED TIMERS ( tri-color)

(1 for each pan arrow button)

Button Bar

Power

ON/OFF

Switch

DISPLAY

Control Panel

PAN LIDS, ONLY used with MOIST products.

(CRISPY products DO NOT require lids)

All electrical connections must be in accordance with local

electrical codes and any other applicable codes.

If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or similarly qualified persons

in order to avoid a hazard.

To prevent an electric shock hazard this device must be

bonded to equipment in close proximity with an equipotential

bonding conductor. This device is equipped with a grounding

lug for this purpose.

WARNING:

Extended Holding Bin

General Market Series

To turn on the unit,

Turn Power On/Off switch (A) to ON position.

NOTE: Load pan covers (if used) and insert pans into the unit.

Allow 20 minutes for heaters to

reach operating temperature.

The button bar will read “WARM

UP” as the unit warms up, they

will display the product names.

Press all Pan Arrow buttons.

The Pan displays will show the assigned product name.

If no product is assigned, the display

will be dim and show “----”. Pressing

the Pan Arrow button will not activate

the timer if “----” is displayed. Pressing

Pan Arrow button when product name

is displayed will start timing cycle.

BKFT (Breakfast) or

REG (Regular Menu)

will be lit depending on

pre-programmed menu.

LED Timing Status

LED TIMERS

RED (steady) = Ready for product

RED (flashing) = Discard product

GREEN (steady) = Oldest product, use first

GREEN (flashing) = Cook more product

YELLOW (steady) = Newer product, use green first

YELLOW (flashing) = Cook more product

When LED is steady RED, load product and press

the Pan Arrow button.

If more than one pan

is active for a product,

the LED for the first

pan loaded will turn

from RED to GREEN.

If only one pan is active

for a product, the LED

will turn from RED to

GREEN.

When any of the timer LED flash, cook more product

or remove and discard product as indicated.

GREEN (flashing) = Cook more product

YELLOW (flashing) = Cook more product

RED (flashing) = Discard product

Operation

The LED for the 2nd pan loaded

with the same product will turn

from RED to YELLOW.

The LED timer can be stopped

(cancelled) at any time by

pressing and releasing the

corresponding PAN Arrow button.

(A)

WARNING: HOT SURFACES

WARNING: This application is not intended for use by persons (including children) with reduced physical, sensory

or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Extended Holding Bin

General Market Series

To change a menu selection for a specific pan cavity, use the following steps:

A. Press and hold the PRINCE CASTLE LOGO button for 6 seconds.

All Pan displays will show PROG. All LED Timers will be RED.

B. Press a Pan Arrow button to change the menu. The LED Timer will

change to YELLOW and the display will change from PROG to the

assigned menu item.

E. Repeat steps A – D as required for other Pan displays. Press the PRINCE

CASTLE LOGO button to exit the Program Mode.

NOTE: A pan may be set as “not used” by assigning “- - - -” as its product.

C. Press the UP or DOWN Arrow

button to scroll to the desired

menu item.

D. Press the ENTER button

to select the menu item.

NOTE: Setting a pan to a particular product will automatically change the other pan in that zone.

To shut down the unit,

turn the Power On/Off switch (A) to OFF position.

WARNING:

Before performing any maintenance, turn the

power switch to the OFF position and unplug

the power cord from the electrical receptacle.

Setting Product Location

Cleaning

(A)

CAUTION:

This unit is not watertight. Do not clean with a water jet/jet spray.

Do not immerse the unit in water.

1. Turn the unit off and unplug the power cord from electrical receptacle.

2. Remove the pans and covers. Wipe all parts and unit with a damp cloth.

DO NOT use a green Scotch Bright pad cleaner, ice or water.

Extended Holding Bin

General Market Series

The unit has multiple shelves, each with an upper and lower heater for each zone.

The heaters follow the default set points of the preset products for each pan

Use the instructions below and the following steps to set the set point temperatures for each heater.

UPPER SHELF LED

This LED will be lit to indicate upper shelf is selected.

PROG LED

This LED will be lit to indicate unit is in Program Mode.

LOWER SHELF LED

This LED will be lit to indicate lower shelf is selected.

ACTUAL TEMP BUTTON and LED

Press to display actual temperature for the

selected heater. LED will be lit when actual

temperature is displayed.

SETPOINT BUTTON and LED

Press to display set point temperature of a

selected heater. LED will be lit when set point

temperature is displayed.

TEMPERATURE DISPLAY

A, B, C, D ( E, F ) = ZONES

Upper and Lower Heater

UP/DOWN ARROW BUTTONS

Used with other Buttons to scroll through heater

and temperature selections.

CROWN BUTTON

Press to enter temperature selections.

CAUTION:

DISPLAYED TEMPERATURES

ARE HEATER TEMPERATURES

AND DO NOT INDICATE ACTUAL

FOOD TEMPERATURES.

NOTE: To reset all calibrations to the factory settings,

turn the unit off, then press and hold the UP and DOWN

Arrow buttons simultaneously while turning the unit back

on. A “P” will appear in the display and all calibrations

will be reset to original factory settings.

Setting the Temperature

The SET PRODUCT TEMP menu is used to change the Hold and Cook-More times.

Press and hold the PRINCE CASTLE LOGO button on the button bar, then immediately press and hold the ENTER button until the display

shows one of six programming menus…..(hold for about 5 seconds)

Use the UP or DOWN Arrow button to scroll to the PROD BURG ↑ ↓ ENTR (Set Product Temperature) menu.

2Press the ENTER button to enter the programming menu, the display should then read SEL TEMP XXXX ↑ ↓ . The XXXX is where the

product abbreviation is displayed. Use the black UP and DOWN arrows to navigate to the desired product.

3Press the ENTER button to select that product profile to update, the display will read SET UPR XXXX ###s↑ ↓ the XXXX is

where the product abbreviation is displayed, and ### is the temperature. Use the UP and DOWN arrows to set the temperature of

the upper heater of that zone. Confirm set point by pressing ENTER

Extended Holding Bin

General Market Series

Setting the Temperature (Continued)

4The display will now show SET LWR XXXX ###s ↑ ↓. Use the UP and DOWN arrows to set the temperature of the Lower heater of that zone.

Press ENTER to confirm setpoint temperature.

5Press PRINCE CASTLE LOGO BUTTON to save the setpoints. Repeat steps 2-5 for all necessary profile upgrades.

Calibrating Heaters

1Use the following steps to calibrate the individual heaters

Press the UP or DOWN Arrow button

until the desired shelf LED and upper

or lower heater is selected.

NOTE: Allow sufficient amount of time

for temperatures to stabilize before

starting calibration. (approx. 30 mins.)

2Take a temperature reading within the shelf near

the center of each heater surface.

NOTE: Use an independent

Temperature meter (not supplied).

WARNING: HOT SURFACES

Use caution when taking

temperature readings

within the shelf.

Press and hold the CROWN BUTTON and ACTUAL TEMP buttons

for 5 seconds. The colon (:) LED indicator will light.

The temperature displayed is the actual heater temperature

sensed by the controller. To clear any offset readings,

press the SETPOINT button.

4Press the UP or DOWN Arrow button until the temperature

displayed matches the reading obtained in Step 2.

Press the CROWN BUTTON to save the temperature

value and exit the Calibration Mode.

Selecting Day Part

Press and hold the SETPOINT button

and the DOWN Arrow button for

3 seconds, the current day part will

begin flashing on the screen.

Use the up/down arrows to select

day part 1 through 3 and the Prince

Castle Crown button to confirm your

selection.

NOTE: Whenever a bin is powered

ON it defaults to DAY PART 1 no

matter what time of day it is.

NOTE: Setpoints are displayed on the front display board, and should be updated according to the product at this point.

Extended Holding Bin

General Market Series

Changing the Hold and Cook-More Times

1The SET PRODUCT TIME menu is used to change the Hold and Cook-More times.

Press and hold the PRINCE CASTLE LOGO button on the button bar,

then immediately press and hold the ENTER button until the display shows one of six programming menus.

Use the UP or DOWN Arrow button to scroll to the PROD TIME ↑ ↓ ENTR (Set Product Time) menu.

2Press and release the ENTER button to enter the Set Product Time menu. The display will show EGGS TIME ↑↓ ENTR.

Use the UP or DOWN Arrow button to scroll through the list of products.

When the desired product is displayed, press the ENTER button to select it.

NOTE: Holding the UP or DOWN Arrow button for longer than 2 seconds will cause the product list to automatically scroll up or down.

The display will show 240 ↑↓ ENTR.

Use the UP or DOWN Arrow button to scroll to the desired Hold time. When the desired Hold time is displayed, press the ENTER

button to save the desired Hold time.

NOTE: Hold time cannot be reduced to less than the Cook-More time plus one minute. NOTE: All times are displayed in minutes only.

For example, 2 and half hours is displayed as 150.

4The display will show COOK 30 ↑ ↓ ENTR.

Use the UP or DOWN Arrow button to scroll to the desired Cook-More time. When the desired Cook-More time is displayed, press the

ENTER button to save it.

NOTE: Cook-More time cannot be increased to more than the Hold time, minus one minute.

5The display will show EGGS TIME ↑ ↓ENTR. Repeat Steps 2 – 4 for any other product.

Press and release the PRINCE CASTLE LOGO button at any time to exit the Program Mode and return to the Run Mode.

NOTE: If the ENTER button has not been pressed to save any changes, the program will revert to the original values.

Extended Holding Bin

General Market Series

Changing Product Names

The EDIT PRODUCT NAME menu is used to change a default product name to one of your own choosing.

Press and hold the PRINCE CASTLE LOGO button on the button bar,

then immediately press and hold the ENTER button until the display shows one of six programming menus.

Use the UP or DOWN Arrow button to scroll to the PROD NAME ↑ ↓ ENTR (Edit Product Name) menu.

2Press and release the ENTER button to enter the Edit Product Name menu.

Use the UP or DOWN Arrow button to scroll through the list of products.

When the desired product is displayed, press the ENTER button to select it.

The first letter (in this case, the E ) will start blinking.

3To change the blinking E, use the UP or DOWN Arrow button to scroll to the desired letter/number/symbol.

When the desired selection is displayed, press the PAN Arrow button to move to the next digit. Repeat for all digits.

NOTE: Holding the UP or DOWN Arrow button for longer than 2 seconds will cause the display to automatically scroll.

When all four digits have been changed, press the ENTER button to select the new name.

The display will show PROD NAME ↑↓ ENTR. Repeat Steps 2 – 4 for any other product.

Press and release the PRINCE CASTLE LOGO button at any time to exit the Program Mode and return to the Run Mode.

NOTE: If the ENTER button has not been pressed to save any changes, the program will revert to the original names.

...

NOTE: The default menu items and names are listed on page 13.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Prince Castle Gewerbliche Lebensmittelgeräte Handbücher

Prince Castle

Prince Castle UHC Series Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-32 Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-CK Series Bedienungsanleitung

Prince Castle

Prince Castle Potato Witch 913 Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-20PUBGBN Bedienungsanleitung

Prince Castle

Prince Castle UHC6PT-22MCD Bedienungsanleitung

Prince Castle

Prince Castle DHB-P1 Bedienungsanleitung

Prince Castle

Prince Castle EHB Series Bedienungsanleitung

Prince Castle

Prince Castle DHB-BK Series Bedienungsanleitung

Prince Castle

Prince Castle TX Series Bedienungsanleitung

Prince Castle

Prince Castle CBT-SB-NA-1PS Bedienungsanleitung

Prince Castle

Prince Castle DHB-BK15 Series Bedienungsanleitung

Prince Castle

Prince Castle 197-BK Series Bedienungsanleitung

Prince Castle

Prince Castle EHB-CE Series Bedienungsanleitung

Prince Castle

Prince Castle Burger King DHB-BK41 Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-33DQ Series Bedienungsanleitung

Prince Castle

Prince Castle CTS Bedienungsanleitung

Prince Castle

Prince Castle Sicom Chef EHB Series Benutzerhandbuch

Prince Castle

Prince Castle DHB-BKF Series Benutzerhandbuch

Prince Castle

Prince Castle DHB2PT-YUM Series Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-GMCN Bedienungsanleitung

Prince Castle

Prince Castle EHB34-CE Series Bedienungsanleitung

Prince Castle

Prince Castle DHB2PT-60P Bedienungsanleitung

Prince Castle

Prince Castle EHB34-2 Series Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch