Rockwell Automation Allen-Bradley XM-124 Bedienungsanleitung

Installation Instructions

XM-124 Standard Dynamic Measurement

Module

Catalog Number 1440-SDM02-01RA

Topic Page

Important User Information 2

North American Hazardous Location Approval 3

Wiring Requirements 4

Install the Module 4

Additional Resources 19

2XM-124 Standard Dynamic Measurement Module

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

Important User Information

Solid-state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines

for the Application, Installation and Maintenance of Solid State Controls (publication SGI-1.1 available from your local Rockwell

Automation sales office or online at http://www.rockwellautomation.com/literature/) describes some important differences

between solid-state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the

wide variety of uses for solid-state equipment, all persons responsible for applying this equipment must satisfy themselves that

each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use

or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and

requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for

actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software

described in this manual.

Reproduction of the contents of this manual,in whole or in part, without written permission of Rockwell Automation, Inc., is

prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING: Identifies information about practices or circumstances that can cause an explosion in a

hazardous environment, which may lead to personal injury or death, property damage, or economic loss.

ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or

death, property damage, or economic loss. Attentions help you identify a hazard, avoid a hazard and

recognize the consequences.

SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people

that dangerous voltage may be present.

BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people

that surfaces may reach dangerous temperatures.

IMPORTANT Identifies information that is critical for successful application and understanding of the product.

XM-124 Standard Dynamic Measurement Module 3

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations.

Informations sur l’utilisation de cet équipement

en environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are

suitable for use in Class I Division 2 Groups A, B, C, D,

Hazardous Locations and nonhazardous locations

only. Each product is supplied with markings on the

rating nameplate indicating the hazardous location

temperature code. When combiningproducts within

a system, the most adverse temperature code

(lowest "T" number) may be used to help determine

the overall temperature code of the system.

Combinations of equipment in your system are

subject to investigation by the local Authority

Having Jurisdiction at the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et non

dangereux.Chaque produit estlivréavec desmarquages

sur sa plaque d'identification qui indiquent le code de

température pour les environnements dangereux.

Lorsque plusieurs produits sont combinés dans un

système, le code de température le plus défavorable

(code de température le plus faible) peut être utilisé

pour déterminer le code de température global du

système. Les combinaisons d'équipements dans le

système sont sujettes à inspection par les autorités

locales qualifiées au moment de l'installation.

WARNING:

Explosion Hazard -

• Do not disconnect equipment

unless power has been removed or

the area is known to be

nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is known

to be nonhazardous. Secure any

external connections that mate to

this equipment by using screws,

sliding latches, threaded

connectors, or other means

provided with this product.

• Substitution of components may

impair suitability for Class I,

Division 2.

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

AVERTISSEMENT:

Risque d’Explosion –

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher

l'équipement.

• Couper le courant ou s'assurer que

l'environnement est classé non

dangereux avant de débrancher les

connecteurs. Fixer tous les

connecteurs externes reliés à cet

équipement à l'aide de vis, loquets

coulissants, connecteurs filetés ou

autres moyens fournis avec ce produit.

• La substitution de composants peut

rendre cet équipement inadapté à une

utilisation en environnement de

Classe I, Division 2.

• S'assurer que l'environnement est

classé non dangereux avant de

changer les piles.

4XM-124 Standard Dynamic Measurement Module

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

Wiring Requirements

Use solid or stranded wire. All wiring must meet the following specifications:

•14…22 AWG copper conductors without pretreatment; 8 AWG

required for grounding the DIN rail for electromagnetic interference

(EMI) purposes

•Recommended strip length 8 mm (0.31 in.)

•Minimum insulation rating of 300V

•Soldering the conductor is forbidden

•Wire ferrules can be used with stranded conductors; copper ferrules

recommended

Install the Module

To install the XM-124 Standard Dynamic Measurement Module, follow these

steps.

1. Mount the terminal base unit.

2. Wire the module.

3. Mount the module.

4. Connect the power supply.

5. Connect the channel outputs.

6. Establish a serial port connection.

7. Establish a DeviceNet connection.

ATTENTION: The XM-124 Dynamic Measurement Module is certified and

approved for use only in the 1440-TB-A/C terminal base unit. Do not install

the XM-124 module in any other terminal base unit.

XM-124 Standard Dynamic Measurement Module 5

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

Mount the Terminal Base Unit

The XM family includes several terminal base units to serve all of the XM

modules. The 1440-TB-A/C terminal base unit is the only terminal base unit

used with the Standard Dynamic Measurement Module (catalog number

1440-SDM02-01RA).

The terminal base unit can be DIN rail or panel mounted.

DIN Rail Mounting

Use the following steps to mount the terminal base unit on a DIN rail

(Allen-Bradley catalog number 199-DR1 or 199-DR4).

WARNING: If you insert or remove the module while backplane power is on, an

electrical arc can occur. This could cause an explosion in hazardous location

installations.

Be sure that power is removed or the area is nonhazardous before proceeding.

ATTENTION: Do not remove or replace a terminal base unit while power is

applied. Interruption of the backplane can result in unintentional operation

or machine motion.

6XM-124 Standard Dynamic Measurement Module

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

1. Position the terminal base unit on the 35 x 7.5 mm DIN rail (A).

2. Slide the terminal base unit over, leaving room for the side

connector (B).

3. Rotate the terminal base unit onto the DIN rail with the top of the rail

hooked under the lip on the rear of the terminal base unit.

31887-M

31883-M

XM-124 Standard Dynamic Measurement Module 7

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

4. Press down on the terminal base unit to lock the terminal base unit onto

the DIN rail.

If the terminal base unit does not lock into place, use a screwdriver or similar

device to open the locking tab, press down on the terminal base unit until it is

flush with the DIN rail, and release the locking tab to lock the base in place.

Wire the Module

Wiring to the module is made through the terminal base unit on which the

module mounts. The XM-124 module is compatible only with the XM-940

terminal base unit, catalog number 1440-TB-A.

XM-940 Terminal Base Unit

XM-940 (catalog number 1440-TB-A)

8XM-124 Standard Dynamic Measurement Module

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

Terminal Block Assignments

The terminal block assignments for the XM-124 Standard Dynamic

Measurement Module are detailed in this section.

TIP

The XM module’s revision number is on the product label, which is

on the front of the XM module, as shown on the example below

(actual product label can have different ratings).

WARNING: EXPLOSION HAZARD. Do not disconnect connections to this

equipment unless power has been removed or the area is known to be

nonhazardous. Secure any external connections that mate to this equipment

by using screws, sliding latches, threaded connectors, or other means

provided with this product.

Revision Number

of XM Module

XM-124 Standard Dynamic Measurement Module 9

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

Terminal Block Assignments

No. Name Description

0 Xducer 1 (+) Vibration transducer 1 connection

1 Xducer 2 (+) Vibration transducer 2 connection

2 Buffer 1 (+) Vibration signal 1 buffered output

3 Buffer 2 (+) Vibration signal 2 buffered output

4 Tach/Signal In (+) Tachometer transducer/signal input, positive side

5 Buffer Power 1 IN Channel 1 buffer power input

Connect to terminal 6 for positive bias transducers or terminal 21 for

negative bias transducers

6 Positive Buffer Bias Provides positive (-5...24V) voltage compliance to buffered outputs

Connect to terminals 5 (CH 1) and 22 (CH 2) for positive bias transducers

7 TxD Personal computer serial port, transmit data

8 RxD Personal computer serial port, receive data

9XRTN

1Circuit return for TxD and RxD

10 Chassis Connection to DIN-rail ground spring or panel mounting hole

11 4-20 mA 1 (+) 4…20 mA output

300Ω maximum load

12 4-20 mA 1 (-)

13 Chassis Connection to DIN-rail ground spring or panel mounting hole

14 Chassis Connection to DIN-rail ground spring or panel mounting hole

15 Chassis Connection to DIN-rail ground spring or panel mounting hole

16 Xducer 1 (-)1Vibration transducer 1 connection

17 Xducer 2 (-)1Vibration transducer 2 connection

18 Signal Common1Vibration buffered output return

19 TACH Buffer Tachometer transducer/signal output

20 Tachometer (-) Tachometer transducer/signal return, TACH Buffer return

10 XM-124 Standard Dynamic Measurement Module

Rockwell Automation Publication 1440-IN001B-EN-P - October 2013

21 Buffer/Xducer Pwr

(-)

Provides negative (-24...9V) voltage compliance to buffered outputs

Connect to terminals 5 (CH 1) and 22 (CH 2) for negative bias transducers

Transducer power supply output, negative side; used to power external

sensor (40 mA maximum load)

22 Buffer Power 2 IN Channel 2 buffer power input

Connect to terminal 6 for positive bias transducers or terminal 21 for

negative bias transducers

23 CAN_High DeviceNet bus connection, high differential (white wire)

24 CAN_Low DeviceNet bus connection, low differential (blue wire)

25 +24 V Out Internally connected to 24V In (terminal 44)

Used to daisy chain power if XM modules are not plugged into each other

If power is not present on terminal 44, there is no power on this terminal

26 DNet V (+) DeviceNet bus power input, positive side (red wire)

27 DNet V (-) DeviceNet bus power input, negative side (black wire)

28 24 V Common1Internally connected to 24V Common (terminals 43 and 45)

Used to daisy chain power if XM modules are not plugged into each other

29 4-20 mA 2 (+) 4...20 mA output

300Ω maximum load

30 4-20 mA 2 (-)

31 Chassis Connection to DIN-rail ground spring or panel mounting hole

32 Chassis

33 Chassis

34 Chassis

35 Chassis

36 Chassis

37 Chassis

38 Chassis

39 SetPtMult Switch input to activate Set Point Multiplication (active closed)

40 Switch RTN Switch return, shared between SetPtMult and Reset Relay

Terminal Block Assignments

No. Name Description

Inhaltsverzeichnis

Andere Rockwell Automation Steuereinheit Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-IB16ISOE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 2198-R031 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-HIST1G Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guard I/O DeviceNet 1732DS-IB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FactoryTalk Analytics LogixAI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EWEB Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-MVI Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro800 2080-MEMBAK-RTC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1794-OB8EPXT Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1794-OB8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1606-XLSCAP24-6 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance Electric LiquiFlo 41L4060 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ControlLogix 1756-HSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation FlexPak 3000 OIM Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley FLEX Ex 1797-IRT8 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-BOOLEAN Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1441-DYN25-MBAL Bedienungsanleitung

Rockwell Automation

Rockwell Automation Micro800 Series Handbuch

Rockwell Automation

Rockwell Automation Allen-Bradley 1756-EN2TSC Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1768-L43 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted T8834 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung