Zeiss Lightsheet Z.1 Bedienungsanleitung

Lightsheet Z.1

Operating Manual

February 2013

ZEN 2012 (black edition)

Carl Zeiss Copyright Lightsheet Z.1

II 000000-1790-528 02/2013

Knowledge of this manual is required for the operation of the instrument. Would you therefore please

make yourself familiar with the contents of this manual and pay special attention to hints concerning the

safe operation of the instrument.

The specifications are subject to change; the manual is not covered by an update service.

communication of its contents are not permitted. Violations will entail an obligation to pay

compensation.

Issued by Carl Zeiss Microscopy GmbH

Carl-Zeiss-Promenade 10

07745 Jena, Germany

microscopy@zeiss.com

www.zeiss.com/microscopy

INTRODUCTION

Lightsheet Z.1 Carl Zeiss

02/2013 000000-1790-528 III

Contents of this Manual

Chapter 1

Hardware

Chapter 2

Sample Preparation

Chapter 3

Quick Guide

Chapter 4

Software Operation

Annex

Lightsheet Z.1 - Overview

CHAPTER 1 - HARDWARE

Lightsheet Z.1 Content Carl Zeiss

02/2013 000000-1790-528 1

CHAPTER 1 HARDWARE

CONTENT

Page

1MAINTENANCE AND CLEANING .........................................................................3

1.1 Maintenance of the Liquid Cooling System.................................................................5

2ERGODRIVE OPERATING PANEL .........................................................................6

3USER INTERFACES ...............................................................................................9

3.1 Installation and Deinstallation of the Detection Modules ........................................10

3.2 Adjustment – Detector Recognition ...........................................................................15

3.2.1 Adjustment – Automatic Detector Alignment..................................................................15

3.2.2 Adjustment – Manual Detector Alignment ......................................................................17

3.2.3 Adjust the Grating Focus for the Automatic or Manual Detector Alignment Tool..............19

3.2.4 Cable Connections for the Detection Module "PCO.Edge"..............................................22

3.2.5 Cable Connections for the Detection Module "Standard" ...............................................23

3.3 Assembly of the Sample Chamber .............................................................................24

3.3.1 Assembly of the Sample Chamber Windows ...................................................................24

3.3.2 Assembly of the Sample Chamber Body and the Sample Chamber Dove Tail Slide............27

3.3.3 Insertion of the Drain Connector, Luer-Lock Connectors and Blind Plugs ..........................29

3.3.4 Insertion of Accessories for Incubation ............................................................................30

3.4 Removing and Inserting the Sample Chamber ..........................................................31

3.5 Assembly of the Sample Holder .................................................................................32

3.5.1 Assembly of the Sample Holder for Capillary ...................................................................32

3.5.2 Assembly of Sample Holder for Syringes..........................................................................34

3.6 Inserting and Removing the Sample Holder..............................................................35

3.7 Installation of the Incubation Modules......................................................................37

3.7.1 Heating Components .....................................................................................................37

3.7.2 CO2-Module Lightsheet Z.1.............................................................................................39

3.7.3 Heating Device Humidity S1............................................................................................41

3.7.4 Registration of the incubation modules...........................................................................41

3.8 Switch Incubation ON and OFF...................................................................................43

CHAPTER 1 - HARDWARE

Carl Zeiss Content Lightsheet Z.1

2 000000-1790-528 02/2013

3.9 Illumination and Detection Optics ............................................................................. 43

3.9.1 Removing and Inserting the Illumination Optics Unit ....................................................... 45

3.9.2 Removing and Inserting the Detection Optics Unit........................................................... 46

3.10 Removing and Inserting the Reflector Turret for Emission Selection ...................... 47

3.11 Removing and Inserting the Reflector Turret for Laser Blocking Filter .................... 49

4INDEX................................................................................................................. 52

CHAPTER 1 - HARDWARE

Lightsheet Z.1 Maintenance and Cleaning Carl Zeiss

02/2013 000000-1790-528 3

1Maintenance and Cleaning

The maintenance to be carried out by the customer is limited to cleaning the painted surfaces, replacing

glass windows and rubber seals on the sample chamber, cleaning and disinfecting the system cavity and

sample chamber, temperature sensors and detection optics unit, replenishment of coolants for the

incubation device and liquid cooling of the detection module as necessary, as well as the replacement of

CO2sterile filters for the incubation device.

a) To clean painted surfaces proceed as follows:

•Switch the device off completely and pull the mains plug.

•Make sure that no cleaning fluid is allowed to enter the system.

•Wipe the painted surfaces with a clean cloth moistened with water to which a small amount of

cleaning agent has been added. Do not use a solvent. Dry off with a lint-free cloth.

b) To clean and disinfect the system cavity proceed as follows:

•Switch the device off completely and pull the mains plug.

•Make sure that no cleaning fluid is allowed to enter the system.

•Take care not to touch the front lens of the illumination and detection optics units. Remove these

optics as necessary.

•Remove the sample chamber for cleaning.

•Cleaning the system cavity:

Wipe the inner surfaces of the system cavity with a clean cloth moistened with water to which a

small amount of cleaning agent has been added. Do not use a solvent. Dry off with a lint-free

cloth.

•Disinfecting the system cavity:

Carefully wipe the inner surfaces of the sample chamber with a lint-free cloth soaked in 70%

ethanol or 70% isopropyl. Allow the solution to react for a few seconds. Repeat the procedure

once or twice as necessary. Carefully wipe off the inner surfaces with a lint-free cloth soaked in

distilled water.

CHAPTER 1 - HARDWARE

Carl Zeiss Maintenance and Cleaning Lightsheet Z.1

4 000000-1790-528 02/2013

c) To clean and disinfect the sample chamber proceed as follows:

•Remove the sample chamber and dismantle it into individual parts. Different procedures are required

for cleaning and disinfecting the various parts of the sample chamber.

−The cover glasses must be properly disposed of in the glass waste.

−The steel parts of the chamber must be cleaned and disinfected as follows:

Rinse the parts with distilled water.

Lay the parts in an ultrasonic bath containing distilled water to which a few drops of detergent

have been added.

Then rinse the steel parts thoroughly with distilled water until all detergent residue has been

removed.

The parts may be laid in a disinfecting bath of 70% ethanol (>1 hour) and then thoroughly

rinsed with distilled water.

The steel parts of the sample chamber may also be autoclaved as necessary.

−Sealing rings, hose connectors and blank plugs must be cleaned and disinfected as follows:

These parts may not be autoclaved.

First of all lay these parts in distilled water and then in a 70% ethanol solution for max. one

hour. Rinse them thoroughly with distilled water.

d) To clean and disinfect the temperature sensor proceed as follows:

•Remove the temperature sensor from the sample chamber and loosen the connections to the main

system module Lightsheet Z.1.

•Once removed, thoroughly rinse the temperature sensor with distilled water and then suspend it for

one hour in a 70% ethanol solution. Make sure that the contact plug remains dry. Complete the

cleaning process by rinsing thoroughly with distilled water.

CHAPTER 1 - HARDWARE

Lightsheet Z.1 Maintenance and Cleaning Carl Zeiss

02/2013 000000-1790-528 5

e) To clean and disinfect the detection optics unit proceed as follows:

•Make sure that no cleaning fluid is allowed to enter the system.

•To avoid scratches, do not wipe the front lens of the optics with dry lens paper and lens cloths.

•Remove these optics from the system cavity as necessary.

•Clean the front lens of optical elements according to general recommendations (see "The clean

microscope" www.zeiss.com/microscopy) using an optical cleaning solution (Carl Zeiss optical cleaning

solution: 85% n - hexan, 15% isopropanol. This solution is not sold by Carl Zeiss Microscopy GmbH)

and a suitable lens cleaning paper or high purity cotton wool.

•In addition to the cleaning procedure described above, for special sterility requirements the front lens

area of the detection modules can be cleaned several times with a lint-free lens cloth or lens paper

soaked in 100% ethanol. Here again, observe the general notes on cleaning the optics

("The clean microscope").

1.1 Maintenance of the Liquid Cooling System

If detection modules in your Lightsheet Z.1 are connected to a liquid cooling system, consider that the pH

value of the cooling liquid changes over time.

To prevent corrosion in the cooler of the detection module, the pH value of the cooling liquid must be

checked at least once a year and the liquid replaced as necessary. Observe the directions of the cooling

system manufacturer in the supplied operating manual.

If you have signed a service agreement with Carl Zeiss, our service staff will perform the check as part of

the maintenance procedure.

The safety data sheet for the cooling liquid should also be observed.

CHAPTER 1 - HARDWARE

Carl Zeiss ErgoDrive Operating Panel Lightsheet Z.1

6 000000-1790-528 02/2013

2ErgoDrive Operating Panel

1Z-axis control

2Rotation button (switches 6 to rotation drive)

3Mode button (fine / coarse)

4Axis button (switches 6 to y-axis drive)

5X-axis control

6Y-axis / Rotation control

Fig. 1 ErgoDrive operating panel

Inhaltsverzeichnis

Andere Zeiss Mikroskop Handbücher

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Zeiss

Zeiss LSM 510 Bedienungsanleitung

Zeiss

Zeiss VivaTome Bedienungsanleitung

Zeiss

Zeiss Axiovert 200 Bedienungsanleitung

Zeiss

Zeiss 880 Installationsanleitung

Zeiss

Zeiss Axiovert 200 Bedienungsanleitung

Zeiss

Zeiss SV 6 Bedienungsanleitung

Zeiss

Zeiss SteREO Discovery Vertical Illumination Device... Bedienungsanleitung

Zeiss

Zeiss TELAVAL 31 Bedienungsanleitung

Zeiss

Zeiss Crossbeam 550L Bedienungsanleitung

Zeiss

Zeiss Axiocam MR Installations- und Betriebsanleitung

Zeiss

Zeiss Axio Observer Series Bedienungsanleitung

Zeiss

Zeiss Axio Observer Series Bedienungsanleitung

Zeiss

Zeiss SIGMA Series Bedienungsanleitung

Zeiss

Zeiss LSM 880 with AiryScan FAST Einrichtungshandbuch

Zeiss

Zeiss Axiovert 40 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungs- und Wartungshandbuch

Zeiss

Zeiss Axiolab 5 Bedienungsanleitung

Zeiss

Zeiss SV8 Bedienungsanleitung

Zeiss

Zeiss Stemi 305 Bedienungsanleitung

Zeiss

Zeiss Axio Zoom.V16 Bedienungsanleitung

Zeiss

Zeiss Definite Focus.2 Bedienungsanleitung

Zeiss

Zeiss OPMI PROergo S7 Bedienungsanleitung

Zeiss

Zeiss LSM 880 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung