Metra Electronics 99-7389B Bedienungsanleitung
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 12/4/19 INST99-7389B
INSTALLATION INSTRUCTIONS
99-7389B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Includes an ASWC-1, AX-CAM6V, antenna adapter, and wiring
harness for a complete installation
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) Climate display • E) (2) #8 x 3/8” Phillips screws • F) Wiring harness (not shown) TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Pick tool
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation ...................................................4-6
Kit Assembly ..........................................................7
Wiring Instructions ...........................................8-15
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Included with kit
Antenna Adapter: Included with kit
Kia Sportage (without NAV, with Display radio†) 2017-2019
† Display radio is an Android Auto/Apple CarPlay radio
A CB D
E
*Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and slide the top of the center
console back slightly. (Figure A)
2. Unclip and remove the panel on the
end of the passenger side of the dash,
then remove (1) Phillips screw exposed.
(Figure B)
3. Unclip the panel above the glove box.
Unplug the passenger airbag light, then
remove the panel. (Figure C)
4. Remove (2) Phillips screws securing the
radio display and a/c vent panel, then
unclip and remove the panel. (Figure D)
Continued on the next page
(Figure A) (Figure C)
(Figure B) (Figure D)
REV. 12/4/2019 INST99-7389B 3
(Figure E) (Figure G)
(Figure F) (Figure H)
DASH DISASSEMBLY (CONT.)
5. Remove (4) Phillips screws securing the
radio. Slide the radio out, then unplug
and remove the radio. (Figure E)
6. Remove (3) Phillips screw securing the
climate control panel. (Figure F)
7. Remove (1) Phillips screw securing the
lower right side drivers knee bolster.
Unsnap the bolster just enough to
access the (1) Phillips screw securing the
climate control panel, then remove the
screw. (Figure G)
8. Unclip the climate/radio control panel
from the dash, unplug the connectors,
then remove the panel. (Figure H)
Continue to Kit Preparation
1.800.221.0932
|
MetraOnline.com
4
KIT PREPARATION
Radio Trim Panel Installation
From the factory radio trim panel:
1. Remove (4) Phillips screws securing the
inner trim panel, then remove the panel.
(Figure A)
To the factory radio trim panel:
2. Secure the 99-7389B r
adio trim panel
to
the panel using with the factory screws.
(Figure B)
Continued on the next page
(Figure A) (Figure B)
REV. 12/4/2019 INST99-7389B 5
KIT PREPARATION (CONT.)
Climate Display Installation
1. Remove (4) Phillips screws securing the
radio/hazard assembly to the climate/
radio control panel, then unclip and
remove the assembly.
(Figure C, heavier arrows)
2. Remove (9) Phillips screws securing
the back cover to the radio/hazard
assembly, then remove the cover.
(Figure C)
3. Using a pick tool, gently release (4)
clips holding the hazard switch to the
assembly, then remove the switch.
(Figure D)
Continued on the next page
(Figure D)
(Figure C)
REV. 12/4/2019 INST99-7389B 7
KIT ASSEMBLY
ISO DDIN radio provision
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
Continue to Wiring Instructions
ISO DIN radio provision with pocket
1. Secure the
radio brackets
to the
pocket
using the (2) #8 x 3/8” Phillips screws
provided. (Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket
assembly, then secure it to the assembly
using the screws supplied with the
radio. (Figure B)
Continue to Wiring Instructions
(Figure A)
(Figure B)
(Figure A)
1.800.221.0932
|
MetraOnline.com
8
FEATURES
COMPONENTS
• Female 3.5mm connector with stripped leads
• ASWC-1
• AX-CAM6V
• Wiring harness
TOOLS REQUIRED
• Crimping tool and connectors, or solder gun, solder, and heat shrink
• Tape • Wire cutter • Zip ties
TABLE OF CONTENTS
Connections ..............................................................................................................................9-10
Installation ...................................................................................................................................10
Final Assembly ..............................................................................................................................11
Programming the ASWC-1 and climate display ..........................................................................11
(ASWC-1) Steering wheel control settings .............................................................................12-15
- L.E.D. feedback
- Changing radio type
- Remapping the steering wheel control buttons
- Dual assignment instructions (long button press)
• Retains audio controls on the steering wheel via an ASWC-1
• Provides NAV outputs (speed sense)
• Retains the factory AUX-IN jack
• Retains the factory backup camera
• Includes an AX-CAM6V 12-to-6V step-down for the factory camera
• Retains balance and fade
WIRING INSTRUCTIONS
REV. 12/4/2019 INST99-7389B 9
CONNECTIONS
The following (1) wire is only for a multimedia/navigation radio that requires this wire.
• Connect the Blue/Pink wire to the VSS/speed sense wire.
• Connect the Blue/White wire from the AX-CAM6V to a wire that has power while the vehicle
is in reverse. This wire will have to be located in the vehicle.
• If retaining the factory AUX-In jack, connect the Red and White RCA jacks to the audio
AUX-IN jacks from the aftermarket radio.
• Connect the Yellow RCA jack to the backup camera input.
Continued on the next page
From the wiring harness included with the kit to the aftermarket radio:
• Connect the (2) Black wires, the Black wire labeled “CAMERA GROUND”, and also the
Black wire from the AX-CAM6V, to the ground wire.
• Connect the Yellow wire to the battery wire.
• Connect the Red wire to the accessory wire.
• Connect the Red wire labeled “CAMERA POWER 6V” to the Blue/Red wire from the AX-CAM6V.
• Connect the Blue wire to the power antenna wire.
• If the aftermarket radio has an illumination wire, connect the Orange wire to it.
• Connect the Gray wire to the right front positive speaker output.
• Connect the Gray/Black wire to the right front negative speaker output.
• Connect the White wire to the left front positive speaker output.
• Connect the White/Black wire to the left front negative speaker output.
• Connect the Green wire to the left rear positive speaker output.
• Connect the Green/Black wire to the left rear negative speaker output.
• Connect the Purple wire to the right rear positive speaker output.
• Connect the Purple/Black wire to the right rear negative output.
1.800.221.0932
|
MetraOnline.com
10
CONNECTIONS (CONT.)
3.5mm jack steering wheel control retention:
The 3.5mm jack is to be used to retain audio controls on the steering wheel.
• For the radios listed below, connect the
female 3.5mm connector with stripped leads
, to the male
3.5mm SWC jack from the wiring harness included with the kit. Any remaining wires tape off
and disregard:
•
Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/White wire
of the connector. Then connect the remaining steering wheel control wire, normally Brown/
White, to the Brown wire of the connector
.
•
Metra OE:
Connect the steering wheel control Key 1 wire
(Gray)
to the
Brown
wire.
•
Kenwood or select JVC with a steering wheel control wire:
Connect the
Blue/Yellow
wire to
the
Brown
wire.
Note:
If your Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood.
See the instructions under changing radio type.
•
XITE:
Connect the steering wheel control SWC-2 wire from the radio to the
Brown
wire.
•
Parrot Asteroid Smart or Tablet:
Connect the 3.5mm jack into the AX-SWC-PARROT (sold
separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.
Note:
The radio must be updated to rev. 2.1.4 or higher software.
•
Universal “2 or 3 wire” radio:
Connect the steering wheel control wire, referred to as Key-A
or SWC-1, to the
Brown
wire of the connector. Then connect the remaining steering wheel
control wire, referred to as Key-B or SWC-2, to the
Brown/White
wire of the connector. If the
radio comes with a third wire for ground, disregard this wire
.
Note:
After the interface has
been programmed to the vehicle, refer to the manual provided with the radio for assigning
the SWC buttons. Contact the radio manufacturer for more information
.
• For all other radios: Connect the 3.5mm jack from the wiring harness included with the kit into
the jack on the aftermarket radio designated for an external steering wheel control interface.
Please refer to the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.
I N S TAL L ATI O N
With the key in the off position:
1. Connect the wiring harness included with the kit to the climate-display/hazard-switch
assembly, and then to the wiring harness in the vehicle.
2. Locate the factory antenna connector in the dash and complete all necessary connections
to the radio. Use the antenna adapter provided to adapt the factory antenna connector to
the aftermarket radio.
3. Connect the wiring harness included with the kit to the ASWC-1.
Attention! If retaining steering wheel controls, ensure that the SWC jack/wire is connected to the
radio before proceeding. If this step is skipped, the ASWC-1 will need to be reset for the steering
wheel controls to function.
Inhaltsverzeichnis
Andere Metra Electronics Autozubehör Handbücher
Metra Electronics
Metra Electronics 99-8723B Bedienungsanleitung
Metra Electronics
Metra Electronics ALOC60 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7392B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-2006 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7316 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-5818 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-5820 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-8223 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7953 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8154 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-3527 Bedienungsanleitung
Metra Electronics
Metra Electronics 2004-2006 Chrysler Pacifica Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5824CH Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7331 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8724B Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7321 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7954 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7322 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8244HG Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7892 Bedienungsanleitung
