Moxa Technologies VPort 354 Bedienungsanleitung

P/N: 1802003540012

Moxa Industrial Video Encoder

VPort 354 Series

Quick Installation Guide

Third Edition, November 2011

- 2 -

Overview

The VPort 354 is a high performance, 4-channel industrial video encoder

that provides up to 4 CIF full frame rate performance (NTSC: 704 x 480 @

30 FPS and PAL: 704 x 576 @ 25 FPS) for each channel, and supports a

dual MJPEG/MPEG4 algorithm, making it especially well-suited for use

with distributed surveillance systems in critical industrial applications. In

addition, a continuous pre/post event trigger video record function will

help system administrators determine why an alarm was triggered.

Two-way audio is provided for the convenience of real-time

communication between system administrators located at the central site,

and engineers in the field.

Package Checklist

The VPort 354 is shipped with the following items:

•VPort 354

•10-pin terminal block for 1 power input and 4 digital inputs

•8-pin terminal block for the other power input, and 2 relay outputs

•5-pin terminal block for the RS-232/422/RS-485 PTZ control port

•Quick Installation Guide

•Document & Software CD (includes User’s Manual, Quick Installation

Guide, Moxa IVN Solution Datasheet and Utility).

•Warranty Card

Note: If any of these items are missing or damaged, please contact your

customer service representative for assistance.

NOTE

Check the model name on the VPort’s side label to determine if

the model name is correct for your order.

NOTE

This product must be installed in compliance with your local laws

and regulations.

Features

High Performance Audio-Video Networking Solution

•Works with NTSC/PAL analog video cameras.

•Supports MPEG4/MJPEG video compression technologies.

•4 BNC video inputs.

•Video stream up to 120 frames/sec in 4CIF (704 x 480) resolution

through a total of 4 channels.

•Selection from 4CIF, 2CIF, CIF, and QCIF resolutions.

•1 audio input and 1 audio output for 2-way voice communication.

•TCP, UDP, and HTTP network transmission modes.

•Supports Modbus/TCP for easy communication with SCADA systems.

•Standard RTSP (Real-time streaming protocol) for easy integration.

•Supports multicast (IGMP) protocols for efficient network

transmission.

•Supports QoS (TOS) for priority transmission.

•Supports SNMP V1/V2c/V3 for network management.

•Built-in web server and RS-232 console for remote access and

configuration.

- 3 -

•Supports one SD card slot (SDHC interface) for recording video on the

SD card if the network is down.

•Two auto-sensing 10/100BaseT(X) Ethernet port or 100BaseFX

•(SC connector) for cascade link or port redundancy.

•Allows a maximum of 8 unicast and 4 multicast output video streams

at the same time.

•Set up video quality in CBR (constant bit rate) or VBR (variable bit

rate).

•Supports 1 RS-232/422/485 DB9 COM port for controlling a PTZ

(PAN/TILT/ZOOM) motorized camera or serial device via TCP/IP

network.

•Supports 1 RS-232/RS-422/RS-485 5-pin PTZ port for controlling a

PTZ (PAN/TILT/ZOOM) motorized camera via TCP/IP network.

•UPnP and IP filtering supported.

Industrial Rugged Design

•Two 12/24 VDC and 24 VAC redundant power inputs with LED

indicators

•-30 to 70°C operating temperature for critical industrial environment

(“T” model)

•35 mm DIN-Rail mounting or panel mounting installation (with

optional accessory)

•IP30 form factor protection

•CE, FCC approvals for industrial applications

Intelligent Alarm Trigger Capability

•Built-in Video Motion Detection (VMD).

•Equipped with 4 DIs and 2 relays (DO) for external sensors and

alarms.

•Pre, trigger, and post alarm snapshot images provided.

•Supports sequential snapshot images.

•Messages with snapshot images can be sent via FTP and email.

•Capable of setting an alarm schedule.

Video Management and Control

•Moxa SoftNVR-IA IP Surveillance Software for viewing and recording.

•Free Moxa VPort SDK Plus supported with flexible interface and

sample code for customized application or system integration.

NOTE

If you are interested in Moxa VPort SDK PLUS, please go to

Moxa

’s website (www.moxa.com) to download the software, or

contact a Moxa sales representative for more information.

- 4 -

VPort 354 Panel Layout

1. Grounding screw

2. RS-232 console port

3. Hardware reset button

4. 8-pin terminal block for Relay 1,

Relay 2, and power input 2 (PWR2)

5. 10-pin terminal block for

DI 1, DI 2,

DI 3, DI 4, power input 1 (PWR1)

6. Heat dissipation orifices

7. LEDs for STAT, PWR1, PWR2,

FAULT

8. LEDs for V1, V2, V3, V4

9. AUDIO INPUT port for mic-in and

line-in connection

10.

AUDIO OUTPUT port for external

speaker

11.

RS-232/422/485 COM port with

DB9 male connector for PTZ

camera or serial device control

12.

RS-232/422/485 PTZ port with

5-pin terminal block for PTZ

camera control

13.

4 BNC connectors for video input

14.

2 RJ45 10/100BaseTX Ethernet

port with 10 Mbps, 100 Mbps LEDs

15.

2 100BaseFX fiber optic port with

100 Mbps LED

16.

SD card slot with LED

17.

Model name

18.

Screw hole for wall mounting kit

19.

DIN-Rail mounting kit

- 5 -

First-Time Installation and Configuration

Before installing the VPort 354, check to make sure that all items in the

package checklist are in the box. In addition, you will need access to a

notebook computer or PC equipped with an Ethernet port.

ATTENTION

The VPort 354 series are high

-performance video encoders

designed to perform without a cooling fan. Therefore, it is

ecommended that each VPort 354 be installed with at least a

5mm clearance on all surfaces to conduce heat

-dissipation.

Step 1: Select the Power Source.

The VPort 354 can be powered by a DC power input from 12 to 32 VDC, or

an AC power input from 18 to 30 VAC. Two power inputs are provided for

redundancy. Users can check the LED status located in the front panel to

see if the power inputs are connected appropriately. If one of the power

inputs fails, the FAULT LED will light up in red if the power failure alarm is

enabled.

NOTE

The VPort 354 series support power input specifications of 12-32

VDC for 12/24 VDC power input, or 18

30 VAC for 24 VAC power

input (note th

at this is different from Moxa EDS switch’s 12-45

VDC power input).

Step 2: Connect the VPort 354 to a Network.

The VPort 354 has 2 auto-sensing 10/100 Mbps RJ45 Ethernet port, or

100 Mbps fiber optic port (multi mode or single mode) for network

connectivity. Both the RJ45 port and fiber optic port have separate LEDs

for 10 Mbps and 100 Mbps connections.

Step 3: Connect the VPort 354 to cameras and an audio source.

The VPort 354 has 4 VIDEO INPUT ports (V1, V2, V3, V4). Use the BNC

connector (1.0 Vpp, 75Ω) and coaxial cable to connect video cameras to

the VPort to input analog video signals.

The VPort 354 has 1 audio input and 1 audio output. A microphone or an

amplifier can be plugged directly into the AUDIO INPUT port, and a

speaker can be plugged into the AUDIO OUTPUT port.

NOTE

Four LEDs (V1, V2, V3, and V4) are located on the VPort 354’s

front panel to

indicate the video signal transmission status for

video inputs. Check the LED status to see if the video is working

properly.

ATTENTION

A ground loop isolator is recommended to be used between the

camera and the VPort

to avoid a sudden current, which is

generated by the electric potential difference between these two

device’s ground power, to burn out the VPort’s chips and boards.

- 6 -

Step 4: Connecting motorized PTZ cameras and serial devices.

The VPort 354 has 2 RS-232/422/485 ports. One is a COM PORT with DB9

male connector, and the other is a PTZ PORT with 5-pin terminal block

connector. Both ports can be used for connecting PTZ control cables for

controlling PTZ cameras over the TCP/IP network.

In addition, the COM PORT with DB9 male connector can also be used to

connect general serial devices, such as card readers, for transmitting

serial data over a TCP/IP network. This port can be used to connect serial

devices to the VPort 354 (however, the port cannot be used to connect

video cameras).

To enable PTZ control, users should configure the PTZ control protocol in

the web-based manager.

NOTE

The PTZ control protocol is not standardized. To use a particular

PTZ control protocol, the video server must support the driver for

that protocol. Currently, the VPort 354 supports PTZ control

protocol drivers for:

1. Pelco D

2. Pelco P

3. DynaColor DynaDome

4. Cohu

If you need to use a protocol that is not on the list, contact the

manufacturer of the camera to get the PTZ control commands,

and then program its PTZ control using the VPort 354

’s

Custom

Camera function.

NOTE

The VPort 354 comes with a PTZ driver upload function for

implementing new PTZ drivers. Please contact a Moxa sales

representative if you need assistance from Moxa

’s R&D

department to create a new PTZ driver.

NOTE

The “Transparent PTZ Control” function in the camera driver list is

used to transmit the PTZ control signal over a TCP/IP network to

the VPort D351 video decoder or PC (additional driver required).

The PTZ control panel or keyboard can directly control the

PTZ

camera or device, eliminating the need for a PTZ camera driver

and allowing the use of PTZ cameras with the VPort encoder.

Step 5: Configure the VPort 354’s IP address.

After powering on the VPort 354, wait a few seconds for the POST (Power

On Self Test) to run. The STAT LED turns green to indicate that the POST

process has completed. The IP address will be assigned when the 10 or

100 Mbps NETWORK LED blinks. The IP address assigned after the POST

is completed depends on the network environment.

Network Environment with DHCP Server

In this case, the IP address of the VPort 354 is assigned by a DHCP Server.

Use the DHCP Server’s IP address table, or use the Moxa VPort utility to

determine the IP address that was assigned by the DHCP Server.

- 7 -

NOTE

After powering on the VPort 354, wait a few seconds for the POST

(Power On Self Test) to run. The IP address will be assigned when

the 10 or 100 Mbps NETWORK LED blinks.

Using the Moxa Ethernet Switch And Video Server Configurator

Utility (edscfgui.exe)

1. Run the edscfgui.exe program to search for the VPort and EDS

switches. After the Utility window opens, select or click on Broadcast

Search, which is located under the List Server menu, to initiate a

search (note that you can also click on Broadcast Search icon

to initiate a search).

NOTE

You may download the VPort and EtherDevice Configurator

software from Moxa’s website at www.moxa.com.

2. The Broadcast Search window will show a list of all switches and

VPorts located on the network. The progress of the search will also

be indicated.

- 8 -

3. When the search has ended, the Model Name, MAC address, and IP

address of the EDS switches and VPorts will be listed in the Utility

window.

NOTE

Broadcast Search can only search for devices connected to the

same LAN subnet as the VPort. If your devices are located on a

different LAN subnet, use the “Specify IP Address” function to

search for the device by keying in the IP address.

4. Double click the selected VPort, or use Internet Explorer to access

the VPort’s web-based manager (web console).

Network Environment without DHCP Server

If your VPort 354 is connected to a network that does not have a DHCP

server, then you will need to configure the IP address manually. The

default IP address of the VPort 254 is 192.168.127.100 and the default

subnet mask is 255.255.255.0. Note that you may need to change your

computer’s IP address and subnet mask so that the computer is on the

same subnet as the VPort.

To change the IP address of the VPort manually, access the VPort’s web

server, and then navigate to the System Configuration Network 

General page to configure the IP address and other network settings.

Check the Use fixed IP address to ensure that the IP address you

assign is not deleted each time the VPort is restarted.

Step 6: Log in to the VPort 354 web-based manager.

Type the IP address in the web browser’s address input box and then

press enter.

Step 7: Install the ActiveX Control Plug-in.

A security warning message will appear the first time you access the

VPort’s web-based manager. The message is related to installing the

VPort AcitveX Control component to your PC or notebook. Click on Yes to

install this plug-in to enable the IE web browser for viewing video images.

- 9 -

NOTE

For Windows XP SP2 or above operating systems, the ActiveX

Control component will be blocked for system security reasons.

In this case, the

VPort’s security warning message window may

not appear. Users should unblock the ActiveX control function or

disable the security configuration to enable the installation of

VPort’s ActiveX Control component.

Step 8: Accessing the homepage of the VPort 354’s web-based

manager.

After installing the ActiveX Control component, the homepage of the

VPort 354’s web-based manager will appear. Check the following items to

make sure the system was installed properly:

1. Video Images.

2. Audio Sound (make sure your PC’s or notebook’s sound is turned

on).

3. Video Information.

Step 9: Accessing the VPort’s System Configuration

Click on System Configuration to access the overview of the system

configuration to change the configuration. Model Name, Server Name, IP

Address, MAC Address, Firmware Version, and LED Status appear in the

green bar near the top of the page. Use this information to check the

system information and installation.

- 10 -

For details of each configuration, check the User’s Manual on the software

CD.

NOTE

After accessing the VPort 354’s web-based manager,

administrators should access

System Configuration



System



Account to set up the administrator’s password and enable

the authentication function. The administrator account name is

admin. An authenticatio

n window will pop up requesting the

account name and password each time the VPort 354 is accessed.

Andere Handbücher für VPort 354

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Handbuch

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-82 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1280I Series Handbuch

Moxa Technologies

Moxa Technologies TCC-120 Handbuch

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2210 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA-T Handbuch

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 354 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80I Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Handbuch

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung