Moxa Technologies IMC-P101 Series Handbuch

Moxa PoE Media Converter

IMC-P101

Hardware Installation Guide

First Edition, November 2009

Reproduction without permission is prohibited.

Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,

R.O.C.

TEL: +886-2-8919-1230

P/N: 1802001015010

- 2 -

Overview

The IMC-P101 series is an Ethernet to fiber optic media converter. It provides

Ethernet media conversion from 10/100 BaseT(X) to 100 BaseFX(SC/ST

connectors). These media converters are classified as power source equipment

(PSE), and when used in this way, the IMC-P101 series provides up to 15.4

watts to powered devices (PD). The IMC-P101 series can be used to power

IEEE 802.3af compliant powered devices (PD), eliminating the need for

additional wiring, and supports IEEE 802.3/802.3u/802.3x with 10/100M,

full/half-duplex, and MDI/MDI-X auto-sensing to provide a total solution for

your industrial Ethernet network.

The IMC-P101 Series includes the following models:

yIMC-P101-M-SC: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, multi-mode port with SC connector, 0 to 60°C operating

temperature.

yIMC-P101-M-ST: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, multi-mode port with ST connector, 0 to 60°C operating

temperature.

yIMC-P101-S-SC: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, single-mode port with SC connector, 0 to 60°C operating

temperature.

yIMC-P101-S-ST: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, single-mode port with ST connector, 0 to 60°C operating

temperature.

yIMC-P101-M-SC-T: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, multi-mode port with SC connector, -40 to 75°C operating

temperature.

yIMC-P101-M-ST-T: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, multi-mode port with ST connector, -40 to 75°C operating

temperature.

yIMC-P101-S-SC-T: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, single-mode port with SC connector, -40 to 75°C operating

temperature.

yIMC-P101-S-ST-T: PoE Industrial 10/100BaseT(X) to 100BaseFX media

converter, single-mode port with ST connector, -40 to 75°C operating

temperature.

NOTE Throughout this Hardware Installation Guide, we often use

IMC as an abbreviation for Moxa Industrial Media

Converter:

IMC = Moxa Industrial Media Converter

- 3 -

Package Checklist

Moxa PoE Media Converter is shipped with the following items. If any of these

items is missing or damaged, please contact your customer service

representative for assistance.

yIMC-P101 series media converter.

yHardware Installation Guide (printed).

yWarranty Card.

Features

y10/100BaseT(X) Auto-Negotiation and Auto-MDI/MDI-X.

yIEEE 802.3af compliant PoE.

yPower failure by relay output.

yProvides up to 15.4W of power to powered devices (PD).

ySupport Store-and-Forward mode and Pass Through mode.

y-40 to 75°C operating temperature range (T models).

yRedundant dual VDC power inputs.

- 4 -

Panel Layout of the IMC-P101 Series

Top Panel View

Rear Panel View

Front Panel View (IMC-P101-M-ST)

1. Grounding screw

2. Terminal block for power

input PWR1/PWR2

3. Heat dissipation vents and

relay output

4. DIP switch

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fiber Link/Active LED

8. 100BaseFX (ST/SC

connector) Port

9. PSE Indicator LED

10. 10/100BaseT(X)

11. TP port 10 Mbps LED

12. TP port 100 Mbps LED

13. Model Name

14. Screw hole for wall

mounting kit

15. DIN-Rail mounting kit

- 5 -

Mounting Dimensions

135.1 mm (5.32 in)

144.45 mm (5.69 in)

101.4 mm (3.99 in)

110.2 mm (4.34 in)

51.65 mm

(2.03 in)

34 mm

(1.34 in)

51.6 mm

(2.03 in)

30.5 mm

(1.2 in)

54 mm (2.13 in)

67 mm (2.64 in)

39.84 mm

(1.57 in)

40.8 mm

(1.61 in)

12.06 mm

(0.47 in)

42.4 mm

(1.67 in)

40 mm

(1.57 in)

Front ViewSide View

Rear View Panel Mounting Kit (Optional)

IMC-P101-M-SC

- 6 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back panel of

the IMC when you take it out of the box. If you need to reattach the DIN-Rail

attachment plate to the IMC, make sure the stiff metal spring is situated

towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN-Rail into the

slot just below the stiff metal spring.

STEP 2:

The DIN-Rail attachment unit will

snap into place as shown below.

metal

spring

DIN-Rail

metal

spring

DIN-Rail

To remove the Moxa Industrial Media Converter from the DIN-Rail, simply

reverse Steps 1 and 2 above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the Moxa PoE

Media Converter on the wall, as illustrated below.

STEP 1:

Remove the aluminum DIN-Rail attachment plate from the Moxa PoE Media

Converter, and then attach the wall mount plates, as shown in the diagrams

below.

⇒

Top

plate

Bottom

plate

- 7 -

STEP 2:

Mounting the Moxa PoE Media Converter on the wall

requires 4 screws. Use the IMC, with wall mount plates

attached, as a guide to mark the correct locations of the 4

screws. The heads of the screws should be less than 6.0

mm in diameter, and the shafts should be less than 3.5

mm in diameter, as shown in the figure at the right.

NOTE Test the screw head and shank size by inserting

the screw into one of the keyhole shaped

apertures of the Wall Mounting Plates, before it

is screwed into the wall.

Do not screw the screws in all the way—leave a space of

about 2 mm to allow room for sliding the wall mount

panel between the wall and the screws.

6.0 mm

3.5 mm

STEP 3:

Once the screws are fixed in the wall, insert the four screw heads through the

large openings of the keyhole-shaped apertures, and then slide Moxa PoE

Media Converter downwards, as indicated below. Tighten the four screws for

added stability.

Grounding the Moxa Industrial Media

Converter

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well-grounded

mounting surface such as a metal panel.

- 8 -

Wiring the Redundant Power Inputs

The top five contacts of the 8-contact terminal block connector on the IMC’s

top panel are used for the IMC’s two DC inputs. Top and front views of one of

the terminal block connectors are shown here.

Top View

Front View

STEP 1: Insert the negative/positive DC wires

into the V-/V+ terminals.

STEP 2: To keep the DC wires from pulling

loose, use a small flat-blade screwdriver to

tighten the wire-clamp screws on the front of the

terminal block connector.

STEP 3: Insert the plastic terminal block

connector prongs into the terminal block receptor,

which is located on the IMC’s top panel.

ATTENTION

Before connecting the IMC to DC power inputs, make sure

the DC power source voltage is stable.

Communication Connections

IMC-P101 models have one 10/100BaseT(X) Ethernet port, and one

100BaseFX (SC or ST type connector) fiber port.

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) Ethernet port located on the IMC’s front panel is used to

connect to Ethernet-enabled devices.

Illustrated below are pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also cable wiring diagrams for straight-through

and cross-over Ethernet cables.

RJ45 (8-pin, MDI) Port Pinouts RJ45 (8-pin, MDI-X) Port Pinouts

Pin Signal

Tx+

Tx-

Rx+

Rx-

Pin Signal

Rx+

Rx-

Tx+

Tx-

- 9 -

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

Straight-Through Cable

RJ45 Plug Pin 1

Switch Port

RJ45

Connector RJ45

Connecto

Tx+

Tx-

Rx+

Rx-

NIC Port

Cable Wiring

3 3

6 6

1 1

2 2

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

Cross-Over Cable

RJ45 Plug Pin 1

Switch Port

(NIC Port)

RJ45

Connector RJ45

Connector

Tx+

Tx-

Rx+

Rx-

(Rx+)

(Rx-)

(Tx+)

(Tx-)

(Tx+)

(Tx-)

(Rx+)

(Rx-)

Switch Port

(NIC Port)

Cable Wiring

3 1

6 2

1 3

2 6

Rx+

Rx-

Tx+

Tx-

100BaseFX Ethernet Port Connection

The concept behind the SC port and cable is quite straightforward. Suppose

you are connecting devices I and II. Unlike electrical signals, optical signals do

not require a circuit in order to transmit data. Consequently, one of the optical

lines is used to transmit data from device I to device II, and the other optical

line is used transmit data from device II to device I, for full-duplex

transmission.

All you need to remember is to connect the Tx (transmit) port of device I to the

Rx (receive) port of device II, and the Rx (receive) port of device I to the Tx

(transmit) port of device II. If you are making your own cable, we suggest

labeling the two sides of the same line with the same letter (A-to-A and B-to-B,

as shown below, or A1-to-A2 and B1-to-B2).

SC-Port Pinouts SC-Port to SC-Port Cable Wiring

Cable Wiring

A A

B B

ST-Port Pinouts ST-Port to ST-Port Cable Wiring

- 10 -

Cable Wiring

A A

B B

ATTENTION

This is a Class 1 Laser/LED product. Do not stare into the

Laser Beam.

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power sources.

If one power source fails, the other live source acts as a backup, and

automatically supplies all of the Moxa Industrial Media Converter’s power

needs.

DIP Switch Setting

1234567

ON DIP

DIP No. Function ON OFF

1 Auto Negotiation Enable* Disable

“ON”: Enables “Auto Negotiation” function, the speed and duplex states for

each port link segment are automatically configured using the highest

performance interoperation mode.

“OFF”: Disables “Auto Negotiation” function, the speed and duplex states

depend on the manual setting configuration.

2 Force TP Speed 100Mbps* 10Mbps

(Only when Auto Negotiation is disabled)

“ON”: Forces 100Mbps on Ethernet port.

“OFF”: Forces 10Mbps on Ethernet port.

3 Force TP Duplex Full Duplex* Half Duplex

(Only when Auto Negotiation is disabled)

“ON”: Forces Full Duplex on Ethernet port.

“OFF”: Forces Half Duplex on Ethernet port.

4 Link Fault Pass Through Enable* Disable

“ON”: Enables “Link Fault Pass Through”, the link status on the TX port will

inform the FX port of the same device and vice versa.

“OFF”: Disables “Link Fault Pass Through”, the link status on the TX port

will not inform the FX port.

5 Operating Mode Store-and-Forward* Pass Through

Andere Handbücher für IMC-P101 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-400 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA Handbuch

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-90 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D351 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5110A Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80 V2.2 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA-T Handbuch

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung