NordicTrack NTEVEL59011 Bedienungsanleitung

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Keep this manual

for future reference.

Model No. NTEVEL59011

Serial No. _

Serial Number

Decal

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you have

questions, or if there are missing

parts, please call:

Or write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds

LS11 8JG

email: [email protected]

www.iconeurope.com

Visit our website at

USER’S MANUAL

08457 089 009

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

HOW TO USE THE CHEST PULSE SENSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

HOW TO USE THE ELLIPTICAL CROSSTRAINER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

NordicTrack is a registered trademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS

WARNING:To reduce the risk of serious injury, read the following important precau-

tions before using the elliptical crosstrainer.

1. Read all instructions in this manual before

using the elliptical crosstrainer. Use the

elliptical crosstrainer only as described.

2. It is the responsibility of the owner to ensure

that all users of the elliptical crosstrainer

are adequately informed of all precautions.

3. The elliptical crosstrainer is intended for

in-home use only. Do not use the elliptical

crosstrainer in any commercial, rental, or

institutional setting.

4. Place the elliptical crosstrainer on a level

surface, with a mat beneath it to protect the

floor or carpet. Keep the elliptical crosstrain-

er indoors, away from moisture and dust.

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. Keep children under age 12 and pets away

from the elliptical crosstrainer at all times.

7. The elliptical crosstrainer should not be used

by persons weighing more than 115 kg (250

lbs.).

8. Wear appropriate exercise clothing when

using the elliptical crosstrainer. Always wear

athletic shoes for foot protection.

9. Always hold the handlebar or the upper

body arms when mounting, dismounting, or

using the elliptical crosstrainer.

10. Keep your back straight when using the ellip-

tical crosstrainer. Do not arch your back.

11. If you feel pain or dizziness at any time

whilst exercising, stop immediately and

begin cooling down.

12. The pulse sensors are not medical devices.

Various factors, including the user's move-

ment, may affect the accuracy of heart rate

readings. The pulse sensors are intended

only as exercise aids in determining heart

rate trends in general.

13. When you stop exercising, allow the pedals

to slowly come to a complete stop. The ellip-

tical crosstrainer does not have a free

wheel; the pedals will continue to move until

the flywheel stops.

WARNING:Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob-

lems. Read all instructions before using. ICON assumes no responsibility for personal injury or

property damage sustained by or through the use of this product.

BEFORE YOU BEGIN

Congratulations for selecting the new NordicTrack®

CXT 910 elliptical crosstrainer. The CXT 910 is an

incredibly smooth exerciser that moves your feet in a

natural elliptical path, minimising the impact on your

knees and ankles. And the unique CXT 910 features

adjustable resistance and incline to help you get the

most from your exercise. Welcome to a whole new

world of natural, elliptical-motion exercise from

NordicTrack.

For your benefit, read this manual carefully before

you use the elliptical crosstrainer. If you have addi-

tional questions, please call our Customer Service

Department at 08457 089 009. To help us assist you,

please note the product model number and serial

number before calling. The model number is NTEV-

EL59011. The serial number can be found on a decal

attached to the elliptical crosstrainer (see the front

cover of this manual for the location of the decal).

Before reading further, please familiarise yourself with

the parts that are labelled in the drawing below.

Upper Body Arm

Water Bottle Holder*

*No water bottle is included

Handgrip Pulse Sensor

FRONT

BACK

RIGHT SIDE

Spring Arm

Pedal Disk

Levelling Foot

Wheel

Pedal

Bookrack

Console

Incline Bracket

Incline Frame

ASSEMBLY

Assembly requires two people. Place all parts of the elliptical crosstrainer in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the two

included allen wrenches, assembly requires a phillips screwdriver , an adjustable

spanner , a rubber mallet , and pliers .

As you assemble the elliptical crosstrainer, use the drawings below to identify the small parts used in assembly.

The number in parenthesis below each drawing refers to the key number of the part, from the PART LIST on

page 26. The second number refers to the quantity used in assembly. Note: Some small parts may have been

pre-attached for shipping. If a part is not in the parts bag, check to see if it has been pre-assembled.

1. Identify the Rear Stabiliser (94), which has two

Levelling Feet (99) threaded into it. Turn the Rear

Stabiliser so the Levelling Feet are closest to the rear

of the Frame (1) as shown. Attach the Rear Stabiliser

to the Frame with the four M10 x 56mm Button Screws

(60) and four M10 Split Washers (22). 22 1

60 22

M10 Nylon Locknut (26)–5

M8 x 19mm Screw (30)–2

M10 x 85mm Bolt (25)–1

M8 Split

Washer (58)–2 M8 Washer (33)–2 M10 Split

Washer (22)–8 M10 Washer (63)–2

M10 x 43mm Button Screw (97)–4

M10 x 56mm Button Screw (60)–4 M10 x 33mm Carriage Bolt (61)–2

V-shaped Groove

Grease

1Tubes

Tubes

3. Slide an M8 Split Washer (58) and an M8 Washer (33)

onto an M8 x 19mm Screw (30). Tighten the Screw

into one end of the Incline Axle (29). Next, apply a

small amount of the included grease to the Incline

Axle.

Align the indicated tubes on the Incline Frame (5) with

the tubes on the Frame (1). Make sure that the

Incline Frame is turned so the V-shaped grooves

are on top. Insert the Incline Axle (29) through the

Incline Frame and the Frame. Note: It may be helpful

to tap the Incline Axle with a rubber mallet to insert it.

Slide an M8 Split Washer (58) and an M8 Washer (33)

onto the other M8 x 19mm Screw (30). Tighten the

Screw into the open end of the Incline Axle (29).

4. Attach the Incline Bracket (24) to the lower end of the

Upright (2) with the M10 x 85mm Bolt (25) and an M10

Nylon Locknut (26). Do not overtighten the Nylon

Locknut; the Incline Bracket must be able to pivot

easily.

2. Attach the Front Stabiliser (90) to the Frame (1) with

the four M10 x 43mm Button Screws (97) and four

M10 Split Washers (22). Make sure that the Front

Stabiliser is turned so the Stabiliser Wheels (45)

are not touching the floor.

22 1

7. Identify the Left Pedal (41). Attach the Left Pedal to the

Left Spring Arm (3) with an M10 x 33mm Carriage Bolt

(61), an M10 Washer (63), and an Adjustment Knob

(77) as shown. Note: The Left Pedal can be attached

in any of five positions (see HOW TO ADJUST THE

PEDALS on page 11).

Attach the Right Pedal (not shown) in the same way.

Make sure that both Pedals are in the same position.

61 41

6. Remove the four M10 Nylon Locknuts (26) from the

welded bolts on the front of the Frame (1).

Whilst a second person holds the Upright (2) near the

Frame (1), connect the Extension Wire Harness (51) to

the Wire Harness (85).

Align the four holes in the bracket at the bottom of the

Upright (2) with the welded bolts on the Frame (1).

Lower the Upright, feeding all slack Extension Wire

Harness (51) and Wire Harness (85) into the

Upright, until the welded bolts are inserted into the

bracket. Do not allow the Wire Harnesses to be

pinched.

Lift the front of the Incline Frame (5). Tighten the four

M10 Nylon Locknuts (26) onto the welded bolts on the

Frame (1).

Welded Bolts

Wire

Harness

35 35

Bookrack

5. The Console (87) requires four 1,5 V (“D”) batteries

(included). Alkaline batteries are recommended. To

install batteries, turn the Console face down and

remove the Battery Cover (84), as shown in the inset

drawing. Insert four batteries into the Console. Make

sure that the negative ends of the batteries

(marked “–”) are facing the springs in the Console.

Then, reattach the Battery Cover.

Connect the console wire harness to the Extension

Wire Harness (51).

Attach the Console (87) to the Upright (2) with the four

Console Screws (35) and the four Console Washers

(93) packaged with the Console. Be careful to avoid

pinching the wires.

Snap the bookrack onto the Console (87) in the indi-

cated location.

Make sure the

Wire Harnesses

(51, 85) do not

get pinched and

damaged during

this step.

Make sure the

Wire Harnesses

do not get

pinched and

damaged during

this step.

9. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may

be left over after assembly is completed.

8. Apply a small amount of the included Teflon®lubricant

to a paper towel. Rub a thin film of the lubricant onto

the Chrome Tubes (21) on the Left and Right Spring

Arms (3, 4). Next, slide the Left Upper Body Arm (7),

which is marked with a sticker, onto the Chrome Tube

on the Left Spring Arm. Slide the Right Upper Body

Arm (75) onto the Chrome Tube on the Right Spring

Arm. Make sure that the Upper Body Arms are on

the correct sides—the upper ends should bend in

the direction shown by the arrows. Next, slide an

Axle Cover (74) onto the post on each Upper Body Arm.

Apply grease to the Arm Axle (19). Insert the Arm Axle

into the right Axle Cover (74) and the Right Upper Body

Arm (75). Next, insert the Arm Axle into the Upright (2)

until the left end of the Arm Axle is flush with the left

side of the Upright. Then, insert the Arm Axle into the

left Axle Cover and the Left Upper Body Arm (7).

Centre the Arm Axle (19). Using the included pedal

tool, tap two Push Nuts (15) about 3 mm (1/8”) onto

each end of the Arm Axle. Make sure that the Push

Nuts are turned as shown in the inset drawing. (Note: It

may be helpful if another person holds a block of wood

against one end of the Arm Axle whilst you tap Push

Nuts onto the other end.) Then, press an Axle Cap (34)

onto each end of the Arm Axle.

Post

Grease

Pedal Tool 15 19 3

HOW TO USE THE CHEST PULSE SENSOR

HOW TO PUT ON THE CHEST PULSE SENSOR

The chest pulse sensor consists of two components:

the chest strap and the sensor unit. Follow the steps

below to put on the chest pulse sensor.

Refer to the inset drawing above. Insert the tab

on one end of the chest strap through one end of

the sensor unit. Press the end of the sensor unit

under the buckle on the chest strap.

Wrap the

chest pulse

sensor

around

your chest.

Attach the

free end of

the chest

strap to the

sensor unit as described above. Adjust the length

of the chest strap, if necessary. The chest pulse

sensor should be under your clothing, against

your skin, and as high under the pectoral mus-

cles or breasts as is comfortable. Make sure that

the logo is right-side-up and facing forward.

Pull the

sensor unit

away from

your body

a few inch-

es and

locate the

two elec-

trode areas on the inner side. Using a saline

solution such as saliva or contact lens solution,

wet both electrode areas. Return the sensor unit

to a position against your chest.

CHEST PULSE SENSOR TROUBLESHOOTING

If the chest pulse sensor does not function proper-

ly, or if the displayed heart rate is excessively high

or low, try the troubleshooting steps below.

• Make sure that you are wearing the chest pulse sen-

sor as described at the left. If the chest pulse sensor

does not function when positioned as described,

move it slightly lower or higher on your chest.

• Each time you use the chest pulse sensor, use

saline solution such as saliva or contact lens solu-

tion to wet the two electrode areas on the sensor

unit (see the drawing below). If heart rate readings

do not appear until you begin perspiring, re-wet the

electrode areas.

• Make sure that you are within arm’s length of the

console. For the console to display heart rate

readings, the user must be within arm’s length of

the console.

• The chest pulse sensor is designed to work with

people who have normal heart rhythms. Heart rate

reading problems may be caused by medical condi-

tions such as premature ventricular contractions

(pvcs), tachycardia bursts, and arrhythmia.

• The operation of the chest pulse sensor can be

affected by magnetic interference caused by high

power lines or other sources. If it is suspected that

magnetic interference may be causing a problem,

try relocating your exercise equipment.

• If the chest pulse sensor still does not function prop-

erly, test the chest pulse sensor in the following way:

Hold the chest

pulse sensor

and place your

thumbs over

the electrode

areas as

shown. Next,

hold the chest

pulse sensor near the console. Whilst holding one

thumb stationary, begin tapping the other thumb

against the electrode area at a rate of about one tap

per second. Check the heart rate reading on the

console.

Chest Strap

Sensor Unit

Tab

Buckle

Electrode Areas

Sensor

Unit

Electrode Areas

Logo

•If the chest pulse sensor does not function properly

after you have followed all of the above instructions,

the battery should be replaced in the following way:

Locate the battery

cover on the back of

the sensor unit. Insert

a coin into the slot in

the cover, turn the

cover counterclock-

wise, and remove the

cover.

Remove the old bat-

tery and insert a

new CR 2032 bat-

tery. Make sure that

the battery is

turned so the writ-

ing is on top.

Replace the battery

cover and turn it

clockwise to close it.

CHEST PULSE SENSOR CARE

• Thoroughly dry the chest pulse sensor after each

use. The chest pulse sensor is activated when the

electrode areas are wetted and the chest pulse sen-

sor is put on; the chest pulse sensor shuts off when

it is removed and the electrode areas are dried. If

the chest pulse sensor is not dried after each use, it

may remain activated longer than necessary, drain-

ing the battery prematurely.

• Store the chest pulse sensor in a warm, dry place.

Do not store the chest pulse sensor in a plastic bag

or other container that may trap moisture.

• Do not expose the chest pulse sensor to direct

sunlight for extended periods of time. Do not expose

the chest pulse sensor to temperatures above 50°

Celsius (122° Fahrenheit) or below -10° Celsius

(14° Fahrenheit).

• Do not excessively bend or stretch the sensor unit

when using or storing the chest pulse sensor.

• Clean the sensor unit using a damp cloth—never

use alcohol, abrasives, or chemicals. The chest

strap may be hand washed and air dried.

CR 2032

Battery

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere NordicTrack Ellipsentrainer Handbücher

NordicTrack

NordicTrack NTEL07808.2 Bedienungsanleitung

NordicTrack

NordicTrack E 15.0 Elliptical Benutzerhandbuch

NordicTrack

NordicTrack Audiostrider Cx650 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack E11.0 Elliptical Kurzanleitung

NordicTrack

NordicTrack CXT 910 Bedienungsanleitung

NordicTrack

NordicTrack E 8.2 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack 30510.0 Bedienungsanleitung

NordicTrack

NordicTrack 831.23665.2 Bedienungsanleitung

NordicTrack

NordicTrack E4.0 Elliptical Bedienungs- und Wartungshandbuch

NordicTrack

NordicTrack EXP14i Bedienungsanleitung

NordicTrack

NordicTrack Smart Terrain 12.0 NTEL01310.4 Bedienungsanleitung

NordicTrack

NordicTrack 29826.3 Bedienungsanleitung

NordicTrack

NordicTrack E4.0 Elliptical Bedienungsanleitung

NordicTrack

NordicTrack E 11.6 Elliptical Einrichtungshandbuch

NordicTrack

NordicTrack COMMERCIAL NTEL16907.0 Bedienungsanleitung

NordicTrack

NordicTrack VGR 850 Bedienungsanleitung

NordicTrack

NordicTrack E 8.5 Elliptical Einrichtungshandbuch

NordicTrack

NordicTrack 831.23946.1 Bedienungsanleitung

NordicTrack

NordicTrack E7.0 Elliptical Einrichtungshandbuch

NordicTrack

NordicTrack Cxt 1200 Elliptical Kurzanleitung

NordicTrack

NordicTrack NTEL05011.0 Bedienungsanleitung

NordicTrack

NordicTrack SpaceSaver Plus Bedienungsanleitung

NordicTrack

NordicTrack Cx 1055 Elliptical Exerciser Bedienungsanleitung

NordicTrack

NordicTrack Cxt 1200 Elliptical Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung