Oneida Air Systems 2005c3HP Bedienungsanleitung

3HP

High Vacuum

Dust Collector

Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204

Phone 1 800 732 4065 315 476 5151 Fax 315 476 5044 www.oneida air.com

Owners Manual

Thank You for Choosing an Oneida Air Systems Product!

OAS manufactures and sells dust collection equipment only. Our qualified technicians and

sales staff are available 7:30am - 6:00pm ST Mon. - Thur. and 7:30am - 5:00pm ST Fri. to

answer any questions concerning OAS products and dust collection. Call for ductwork design

and ductwork quotes, including system pricing and shipping cost.

Table of Contents

Page

Read the entire Owners Manual efore installing or operating system!

II.

III.

IV.

VI.

VII.

VIII.

IX.

XI.

XII.

XIII.

XIV.

7 - 8

System Start-Up Information

Direct Drive Configurations

General Specifications & Fan Performance Curve

Dimensions

Stand Assembly

General Assembly Instructions

Fan / Blower Maintenance

Filter Maintenance

Wire Diagram

Accessories

Troubleshooting

Fire Hazards - Read Before Installing System

Terms and Conditions

Fan Motor Maintenance

Proudly

Made in

the U.S.A.

O.A.S. 2005

3HP High Vacuum Owners Manual

O.A.S. 2005

3HP High Vacuum Owners Manual

I. System Start-Up Information

1. Read the installation and maintenance instructions as well as the recommended

safety practices in this manual.

2. Install Ductwork completely:

A.) Seal ductwork with silicone sealant or duct tape.

B.) Have Dust Bin in place and sealed.

3. Have licensed electrician wire Fan / Blower according to wire diagram in this

owners manual.

4. Have licensed electrician check current draw on motor with all gates open. Current

draw should not exceed maximum motor amperage. (OAS is not responsible for

destroyed motors.)

Caution

The Dust Collector & Fan/Blower is heavy. Handling and

installation should always be performed by experienced and

trained personnel who have experience with rotary equipment.

In addition to the following instructional manual, care should

be taken to ensure compliance with specific safety

requirements mandated by federal, state and local codes.

arning

Do not operate Fan / Blower without connecting ductwork.

Never operate Fan/Blower without belt and shaft guard in

place. Keep clear of exhaust. Keep hands and objects clear

of inlet and outlet.

arning

Check amperage draw during operation with all blast gates

open. Make certain amperage is not outside operating limit

indicated on motor plate! If amperage is too high shut down

immediately! (See Troubleshooting section.)

II. 3hp High Vacuum Configuration

O.A.S. 2005

3HP High Vacuum Owners Manual

Pleated

Cartridge

Filters

(Do not remove

fabric straps

from cartridge.)

Removable

Dust

Container

Removable

55 Gal. Metal

Chip / Dust Bin

3hp Integral

Fan Blower

Angle Iron

Stand

Flex Hose

Outlet

Inlet

lbow

Square-to-Round

Cone

Cyclone

O.A.S. 2005

3HP High Vacuum Owners Manual

III. General Specifications & Fan Performance Curves

Physical and Electrical Data for 3 hp High Vacuum Unit.

3hp - 1342 cfm @ 3.5 SP

System Performance

Height w/ 55 Gal. Drum: 110 1/8

Footprint: 56 x 34

Fan Wheel diameter: 15 Backward Incline design

Cyclone Inlet: 6

System Dimensions

T FC 60 Hz Motor - Single Phase

Insulation Class: F4

Voltage: 230

Amperage: 14.5

Made in U.S.A.

Integral Fan Blower - 3hp

1 Pleated Cartridge - 130 sq. ft.

Spun-Bonded polyester BIA ZH1 / 487 test - Rated C

Captures 99.99% of test material over 20 microns

Captures 99.9% of test material between 0.2 - 2.0 microns @ 11fpm

External Cartridge Filter

55 Gal. Steel Drums

Large dust bins available

Dust Bin

Magnetic Motor Starter

Filter fficiency Gauge

Included

Static pressure and volume together determine a fans performance. Several factors, such as layout of

ductwork and diameter of openings, can affect a fans performance.

0 200 400 600 800 1000 1200 1400 1600

CFM

Static Pressure at Cyclone Inlet

System Performance Curve

12.5 10.9

9.1

6.8

3.5

1342

1045

842

618

3.5

6.8

9.1

10.9

12.5

CFM Static @

Cyclone Inlet

IV. Dimensions

O.A.S. 2005

3HP High Vacuum Owners Manual

22

6 1/8

4

28 1/2

7 1/4

36

75 3/4

111 7/8

12

62

30 7/8

10.031

I.D.

7.64

I.D.

1.25

Flange

For Minimum Mounting Heights

with 55 gal. drum

26 1/8 O.D. of

Mounting Ring

Bolt Holes

24 7/8

18

56

Outlet Size

56

7 3/4

14 1/8 18

74 1/8

17 3/16

12 1/8

5 1/16

For Twin 55 Gal. Barrel Measurements

See Page 9.

O.A.S. 2005

3HP High Vacuum Owners Manual

V. Angle Iron Stand

Bolt together the stand using the cross bars and 3/8 x 1 bolts. Note: the cross bar on

the cyclone stand goes in the back so that the dust bin can slide out.

55 Gal.

30 7/8

28 7/8

75 7/8

O.A.S. 2005

3HP High Vacuum Owners Manual

Cyclone

Barrel

Cyclone

Cone

2. Clamp the fan housing and cyclone barrel to

the cyclone cone with the clamp ring. Note: the

fan / blower and the cyclone barrel are very

heavy. The system will be top heavy. One method

is to lay the stand down, then bolt the cyclone

with the fan / blower to the stand. The iron ring

will slide into stand.

3. Tip the fan housing and cone upright. The

system is very top heavy.

4. Bolt the elbow-cartridge housing to the fan

housing outlet (rectangular). Clamp the cartridge

to the flat plate. Clamp the dust bins to the

bottom of the cartridge filters.

Continued on next page.

Pleated

Cartridge

Filters

(Do not remove

fabric straps

from cartridge.)

Removable

Dust

Container

5hp Integral

Fan Blower

Angle Iron

Stand

Outlet

Inlet

lbow

Square-to-Round

Cone

Cyclone

Clamp

Ring

VI. Assembly Instructions

Cyclone

Barrel

Air Inlet

Fan / Blower

1. Orient the blower housing to match the stand

configuration and the desired angle for the cyclone inlet.

Bolt the fan / blower to the cyclone barrel using the

hardware taped on the motor.

Bolts are already welded on Fan/Blower unit. Put strip

of the neoprene gasket around the cyclone barrel behind

the bolt holes. Then put bolts through holes in barrel.

Put flat washer on bolt. then lock washer, then hex nut.

Cyclone Inlet and Fan / Blower are independent.

Filters can be to the right or left of the unit.

Air

Outlet

Neoprene

Gasket

Material

16 ea. 3/8 Flat Washers, Lock Washers and Hex Nuts

Fan / Blower is shipped strapped to Cyclone Barrel. It is

NOT attached to the unit. You must olt them together.

Follow the instructions elow.

One bolt hole

on each side.

Do NOT use

hook on motor

to lift unit.

VI. Assembly Instructions (Cont.)

O.A.S. 2005

3HP High Vacuum Owners Manual

5. Attach flex hose to bottom of collector and to lid of

dust bin. Securely fasten hose clamps. There must be

an air tight seal between the collector and dust bin.

6. Make sure the dust bin lid sits securely and the rubber

gasket on the bin lid is in place on the barrel. Maintain

an air tight seal between cyclone and dust bin to prevent

motor from overloading.

IMPORTANT:

Do not operate the collector until the dust bin is in place and

the connector is air tight or motor damage could result!

Stay clear of fan exhaust while collector is operating.

Collector

Hose Clamp

Flex Hose

Dust Bin

7. Attach the ductwork from the woodworking machines to the inlet of the collector.

8. Bolt Angle Iron Stand to the floor. Unit is top heavy!

VII. Fan / Blower Maintenance

A high pressure blower requires a certain amount of resistance which will prevent motor

over amperage.

Make sure power source matches wire voltage configurations.

Check set screw and key in fan wheel, make sure fan wheel is secure. Fan blower should

not vibrate.

1. Electrical - Failure to follow instructions and safe electrical procedures could result in serious injury or death.

Disconnect all power and discharge all capacitors before servicing. Install and ground per local and national

codes. Consult a licensed electrician with questions or if repairs are required.

lectrical Connections -

A.) All wiring, fusing, and grounding must comply with National lectrical Codes and local codes.

B.) To determine proper rotation and voltage connections, refer to the Wire Diagram of this manual.

C.) Use the proper size of line current protection and motor controls as required by the National lectrical Code

and local codes. Recommended use is 125% of full load amps as shown on the nameplate for motors with

40 degrees Celsius ambient and a service factor over 1.0. Recommended use is 115% of full load amps as

shown on the nameplate for all other motors. Do not use protection with larger capacities than recommended.

Three phase motors must have all three phases protected.

2. Cleanliness - Keep both the interior and exterior of the motor free from dirt, water, oil, and grease.

3. Safety - Motors should be installed, protected and fused in accordance with latest issue of National lectrical

Code, N MA Standard Publication No. MG 2 and local codes. Rotating parts such as pulleys, coupling, external

fans, and unusual shaft extensions should be permanently guarded. Keep hands and clothing away from

moving parts. lectrical repairs should be made by trained, qualified personnel only.

4. Service - Notice - If lubrication instructions are shown on the motor nameplate, they will supercede this

general instruction.

Warning: Rotating Fan Blades. Keep Objects Clear of Inlet and Outlet.

VIII. Filter Maintenance

3HP High Pressure Owners Manual O.A.S. 2005

External Filter Cartridge Cleaning Intervals

Caution Fine dust collected in filter is hazardous

to your health! Do not breathe!

When unit is turned off, use compressed air to blow dust off from

exterior of filter. Hold nozzle at least 8 away from filter pleats*.

Do not remove bottom dust pan before or during the blow-off

process! Let dust settle into dust pan. Unclip and dump out dust.

Filter removal is not required. You can also run your fingers

around the filter pleats to knock material down.

* WARNING: A close, direct blast with the compressed air nozzle

too close to filter, may damage filter media. Always wear safety

glasses while blowing off filter.

Do not

remove

fabric

straps.

55 Gal. 55 Gal.

3hp High Vac Stand

(Twin 55 Gal. Barrels)

STZ050255

12

8

44

16

24

32 1/2

10

17 1/2

36

3 6 3

22

60

8

4

6 1/8

10 x 10 x 10

Splitter

22

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000014 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXVM001500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD002030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK050100 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung