Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Rev: 12/03/2018 Doc. #ZBM000104

Appearance may vary slightly

U.S. Patent: #8491685

U.S. Patent: #9370740

U.S. Patent: #8514090

U.S. Patent: #8496719

U.S. Patent: #7247180

OWNER’S MANUAL

Dust Gorilla Pro

Dust Collector

with SMART Boost

3 HP/5 HP

# XGK030035

# XGK030055

# XGK050035

# XGK050055

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications for 3 HP 4

System Specications for 5 HP 5

System Dimensions for 35 Gallon Drum 6

System Dimensions for 55 Gallon Drum 7

System Contents 8

Assembly Instructions 10

Maintenance 18

Troubleshooting 19

Recommended Accessories 20

Warranty Information 22

Notes 23

2Oneida Air Systems

System Start-Up Information

1. Install ductwork completely before operating collector

a. Seal ductwork with silicone sealant or duct tape.

b. Have dust drum in place and sealed.

2. DO NOT operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place. Dust Drum and

Cyclone must be in place and sealed or motor will overheat!

3. DO NOT operate without lter in place. Fan blade can cause serious injury.

4. e Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! It is recommended

that at least two people li the system up.

5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated

on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or

failure to follow these directions).

6. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

7. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

8. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

9. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deagrate

(burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame

front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise

additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been

witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

Make sure to read and understand the installation and maintenance instructions as well as all

recommended safety practices.



3oneida-air.com

System Start-Up Information (Continued)

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Personnel should be kept at least 20 . away from unit.

9. Check dust bin frequently and before leaving the shop for smoldering material.

10. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

11. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

12. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

13. Empty dust bin and clean lter oen, especially when sanding.

14. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

15. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Trapped metal when drawn into the collector can spark against ductwork.

e. Check wood stock for old nails and screws which can create red hot metal fragments.

16. Avoid using excessively large wood waste bins.

17. ALWAYS check storage bins for smoldering material before leaving for the day.

18. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

19. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

20. UNPLUG UNIT BEFORE SERVICING OR CLEANING

OAS Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4Oneida Air Systems

System Specications for 3 HP

OPERATION

Fan Rating (Free Fan) 3 HP: 2,940 CFM

Fan Rating (with Cyclone & Filter) 3 HP: 1,340 CFM

Maximum Suction Rating 3 HP: 23" WC

MOTOR AND ELECTRICAL

Motor Type U.S. Made TEFC Motor

Motor Insulation Class F

Motor Service Factor 1.15

Horsepower 3 HP

Motor Speed 3,500-4,500 RPM

Phase Single-Phase (1ph)

Voltage 208-230V

Cycle 60Hz

Listed FLA 3 HP: 15-17.5A

On/O Switch Remote Starter with Push button On/O Switch and RF Keyfob

Power Cord 10 ft

Power Connector Wire

Recommended Circuit Size 30A

Sound Emission With Stacking Sound Filter: 80 - 82 dBA @ 10 ft

IMPELLER

Size 15"

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter Media Type G.E. H12 HEPA

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 110 Sq. Ft.

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Heavy-gauge cold-rolled steel

Inlet 7" Diameter

Overall Height (with 35 Gallon Drum) 94"

Overall Height (with 55 Gallon Drum) 106"

5oneida-air.com

System Specications for 5 HP

OPERATION

Fan Rating (Free Fan) 5 HP: 3,250 CFM

Fan Rating (with Cyclone & Filter) 5 HP: 1,625 CFM at 3" WC

Maximum Suction Rating 5 HP: 23”WC

MOTOR AND ELECTRICAL

Motor Type U.S. Made TEFC Motor

Motor Insulation Class F

Motor Service Factor 1.15

Horsepower 5 HP

Motor Speed 3,500-4,500 RPM

Phase Single-Phase (1ph)

Voltage 208-230V

Cycle 60Hz

Listed FLA 5 HP: 18-23A

On/O Switch Remote Starter with Push button On/O Switch and RF Keyfob

Power Cord 10 ft

Power Connector Wire

Recommended Circuit Size 30A

Sound Emission With Stacking Sound Filter: 80 - 82 dBA @ 10 ft

IMPELLER

Size 15"

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter Media Type G.E. H12 HEPA

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 110 Sq. Ft.

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Heavy-gauge cold-rolled steel

Inlet 7" Diameter

Overall Height (with 35 Gallon Drum) 94"

Overall Height (with 55 Gallon Drum) 106"

6Oneida Air Systems

Nominal dimensions shown with a 35 gallon drum. Dimensions subject to slight variations in manufacturing.

System Dimensions for 35 Gallon Drum

Top View

94"

2,388 mm

18"

457 mm

48"

219 mm

75.5"

1918 mm

30"

762 mm

27"

686 mm

30"

762 mm

203 mm

36"

914 mm

16"

406 mm

56"

1,422 mm

66.5"

1,689 mm

25"

635 mm

7oneida-air.com

Nominal dimensions shown with a 55 gallon drum. Dimensions subject to slight variations in manufacturing.

System Dimensions for 55 Gallon Drum

Top View

106"

2,,692 mm

18"

457 mm

48"

219 mm

87.5"

2,223 mm

30"

762 mm

36"

914 mm

16"

406 mm

68"

1,727 mm

78.5"

1,994 mm

37"

940 mm

203 mm

27"

686 mm

30"

762 mm

8Oneida Air Systems

System Contents

Please unpack the parts carefully and conrm you have

received each item listed here.

You will need the following:

• 7/16" Wrench

• 7/16" Socket Wrench

• 1/2" Wrench

• 1/2" Socket Wrench

• 1/2" Deep Impact Socket

• 8' Ladder

• Tape Ruler

• Scissors

• Razor Knife

• Diagonal Cutters

• Spirit Level

• Anchor Screws

ID Part number Part description Qty

A BXI030118C

BXI050118C

Motor Assembly 3 HP 1 PH

Motor Assembly 5 HP 1 PH

B BHX020005B Fan Housing 1

C SXI002100 Barrel 1

D SCX002100 Cone 1

E ACB120000 12" Clamp Band 2

F DHF090001 9" Diameter Flex Hose 1

G SEX550900 Steel Drum Lid with 9" Collared

Lid 1

H"SES350000

SES550000"

35 Gallon Steel Drum with Clamp

55 Gallon Steel Drum with Clamp 1

I FCS183600HF 13” x 36” HEPA Cartridge Filter 1

J GXF010018 18" Plenum Kit 1

J1 FPX000001 Filter Plenum Elbow 1

J2 FPX010018 18" Filter Plate 1

J3 BSC180000 Drop-in Silencer 1

J4 FPZ000018 Fine Dust Bin 1

J5 AHX001318 Plenum Hardware Kit 1

J5A AFJ051602 5/16-18” x 2” J Bolt 8

J5B AFT000001 5/16-18” Thumb Nut 8

J5C AFB516125 5/16-18 x 1.25" Bolt 9

J5D AFW180000 5/16" Flat Washer 9

J5E AFT155175 5/16-18” Whiz-Lock Nut 9

ID Part number Part description Qty

K AHX000001A SMART Gorilla Hardware Kit 1

K1 RGZ000000 Neoprene Foam Gasket Roll 25 ft.

K2 AFT051618 5/16-18" U-Spring Nut 8

K3 AFW180000 5/16" Flat Washer 40

K4 AFB155155 5/16-18" x 1" Flange Bolt 16

K5 AFB155190 5/16-18" x 1" Hex Head Bolt 12

K6 AFT155175 5/16" Whiz-Lock Nut 12

K7 FGA000002

14” Grounding Cable with

8-18 x 3/8” Self-tapping

Screws

K8 AFS015100 3/8-16" x 1" Hex Head Bolt 7

K9 AFS015700 3/8-16" x 1.25" Hex Head Bolt 3

K10 AFW190000 3/8" Flat Washer 20

K11 AFT000004 3/8” Whiz-Lock Nut 10

K12 AXD000006 1" Hook Tape 4 in.

K13 AXD000007 1" Loop Tape 4 in.

L STX002100A Plenum Support Brace 1

M STZ212300 Stand Assembly 1

N BSS181600 18" Dia Stacking Sound Filter 1

O AMR240000 Remote 1

P AXB999110B Dust Sentry 1

If you cannot find an item on the list examine the packaging materials very carefully. Certain

components may have been pre-installed for shipping purposes. There may be hardware

leftover.



Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK050100 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini GORILLA XXP010101 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Gorilla XXP999901 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK100300 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Pro XXS200001 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung