Oneida Air Systems Supercell XSK000014 Bedienungsanleitung

Supercell®

High-Pressure

Dust Collector

14 Gallon

# XSK000014

Rev: 07/20/2020 Doc. #ZBM000037

Appearance may vary slightly

OWNER’S MANUAL

oneida-air.com 1

Table of Contents

System Start-Up Information 2

System Specications 4

System Dimensions 5

System Contents 6

Assembly Instructions 8

Maintenance 20

Troubleshooting 24

F.A.Q. 25

Recommended Accessories 26

Warranty Information 28

Notes 29

Oneida Air Systems, Inc.2

System Start-Up Information

1. Install ductwork/ex hose completely before operating collector.

a. Seal ductwork with silicone sealant or duct tape if leaks are found.

b. Have dust drum in place and sealed.

2. DO NOT operate without lter in place. Debris will cause damage to the motor!

3. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.

4. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

5. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

6. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

7. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

8. Ensure that your dust collector is turned o and unplugged during installation.

9. Use this equipment for dry material collection only. DO NOT use for liquid collection.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Air borne wood dust below 420 microns in size (0.017 of an inch) in certain concentration ranges when ignited can

deagrate (burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding

ame front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can

raise additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has

been witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

MAKE SURE TO READ AND UNDERSTAND THE INSTALLATION AND MAINTENANCE INSTRUCTIONS AS

WELL AS ALL RECOMMENDED SAFETY PRACTICES.

oneida-air.com 3

System Start-Up Information (Continued)

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Check dust bin frequently for smoldering material and before leaving the shop.

9. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

10. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

11. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

12. Empty dust bin and clean lter oen, especially when sanding.

13. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

14. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Trapped metal when drawn into the collector can spark against ductwork.

e. Check wood stock for old nails and screws which can create red hot metal fragments.

15. Avoid using excessively large wood waste bins.

16. ALWAYS check storage bins for smoldering material before leaving for the day.

17. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

18. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

19. UNPLUG UNIT BEFORE SERVICING OR CLEANING

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

Oneida Air Systems, Inc.4

System Specications

OPERATION

Maximum Suction Rating 97.8" WC

MOTOR AND ELECTRICAL

Motor Type 3x 1300W Modular Motors

Horsepower 5HP Total

Motor Speed 48,880 RPM

Phase 1-Phase

Voltage 208-230V

Cycle 60HZ

Listed FLA 18A

On/O Switch Magnetic Starter with On-O Switch and RF Remote

Power Cord Length 10 feet

Power Connector NEMA 6-20

Recommended Circuit Size 20A

Recommended Circuit Type HACR

Sound Emission 80 dBA @ 10 ft

CARTRIDGE FILTER

Filter Media Type HEPA Certied

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 40 sq ft

SYSTEM DIMENSIONS AND CONSTRUCTION

Primary Build Materials Cold Rolled Steel, Static Dissipative Polyethylene

Inlet 4" O.D.

Discharge to Drum 5" O.D.

Overall Height 14 Gallon: 61"

Overall Weight 14 Gallon: 76 lbs

e Supercell requires a 20 Amp

outlet receptacle to be installed by a

licensed electrician.

23.119

oneida-air.com 5

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing. Mounting dimensions

allow for 13/16" clearance when removing and emptying the drum

Allow for an additional 24" of clearance above the Motor Assembly to allow for its removal during lter

replacement and other maintenance. Allow for an additional 3" of clearance around the system for ease of access

to the latches.

System Dimensions

13/16"

21 mm

36-13/16"

935 mm

Floor

21-9/16"

548 mm

20"

508mm

23"

587mm

24-1/4"

616 mm

61"

1,549 mm

Oneida Air Systems, Inc.6

System Contents

Please unpack the parts carefully and conrm you have received each item listed here.

* Some components are pre-installed at the factory and are listed here for your convenience.

ID Part number Part description Qty

A BXI001501 Supercell Motor Assembly 1

B FPX040001 Filter Hold Down Plate 1

C FCS131040H 13" x 13" Conical HEPA Cartridge Filter 1

D GCZ150000 15" Ring Clamp 1

E SCX040000 Cyclone 1

E1* DGA040000 4" Aluminum Blast Gate 1

E2* DAB040000 4" Male Duct Adapter 1

E3* AFR316066 Rivets 5

F SMS040001 Supercell Wall Bracket 1

G AHX000021 Supercell 14 Gal. Model Hardware Pack 1

G1 ZBT040001 Supercell Wall Bracket Template 1

G2 RGF000015 15" Barrel Gasket 1

G3 RGZ051820 Supercell Flange Gasket 1

G4 AFS015920 1/4"-20 x 3/4" Hex Head Bolt 6

G5 AFW025000 1/4" Flat Washer 6

G6 AFT900006 1/4"-20 Nylock Nut 6

G7 AFB155180 5/16-18 x 2-1/2" Hex Head Bolt 4

G8 AFW180000 5/16" Flat Washer 4

G9 AFW180516 5/16” Rubber Washer 4

G10 AFT155175 5/16 "Whiz-Lock Nut 4

G11 AFT900516 5/16" - 18 Nylock Nut 4

G12 AFW516075 5/16x 3/4" Nylon Spacer 1

G13 SMS040000 Rear Support Brace 1

G14 AFL990001 Latches 2

G15 AFS501032 10-32 1/2" Phillips Pan Head Screws 4

G16 AFT901032 10-32 Nylock Nut 4

ID Part number Part description Qty

G17 AFB155180 5/16-18 x 2-1/2" Hex Head Bolt 2

G18 VRV050500 1/2" ID Clear Vinyl Tubing 7

G19 AHX000018 Quick Disconnect Kit 1

G19A RLH000006 1/4" NPT Nylon Elbow 1

G19B RLH000005 3/8”Socket 1

G19C RLH000004 3/8" Male Plug 1

G19D RLH000002 Nylon Washer 1

G19E RLH000003 Rubber O Ring 1

G19F RLH000007 Nylon Nut 1

G19G RLH000008 Round Tapered Plug 1

G20 AXD600300 9-17 Gallon Drum Liner Bag 5

G21 RLH000023 23 mm Button Plug 1

G22 ACB640000 4-1/2" Turn-Key Band Clamp 2

G23 RGZ470114 Bin Gasket 4

G24 AMR000000 Remote Control Key Fob 1

H DHF042502 4" x 25' Vacuum Pressure Rated Flex-Hose 1

I AXB999110B Dust Sentry Automatic Bin Level Indicator 1

J SMD140400 Drum Assembly 1

J1 SDS140000 14 Gallon Molded Drum 1

J2* RHL000604 Drum Window 1

J3* AFS103258 10-32 5/8" Phillips Pan Head Screws 4

J4* AFT901032 10-32 Nylock Nuts 4

J5 RHC000012 3" Caster with 5/16"-18 x 3/4" Stems 5

If you cannot find an item on the list, examine the packaging materials very carefully for nested items. Please

note that certain components have been pre-installed. There may be hardware leftover.

oneida-air.com 7

G10

G11

G12

G13

System Contents (Continued)

G19

G19A

G19E G19F

G19G

G19B G19C

G19D

G20

SHEET 1 OF 1

NAME:

14Ga Galv

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

Oneida Air Systems Inc. AND SHALL

NOT BE USED OR DISCLOSED TO

OTHERS, IN WHOLE OR IN PART,

WITHOUT THE WRITTEN AUTHORIZATION

OF Oneida Air Systems Inc.

PART NO.

SIZE

DO NOT SCALE

DRAWN DATE:

7/18/2019

ONEIDA AIR SYSTEMS INC.

1001 WEST FAYETTE STREET

SYRACUSE, NEW YORK 13204

1-800-732-4065

MFG APP:

DRAWN BY:

ENG APP:

TOL:

.XX

.10

.XXX

.015

PROPRIETARY AND CONFIDENTIAL

MATERIAL:

FINISH:

DIMENSIONS

ARE IN

INCHES

REV:

FPX040001

3RD ANGLE

FPX040001 - Filter Hold Down 14ga rev 3

KWG

G14 G15

G16

G18

G21

G23

Thewall bracket should be installed to a sturdy, reinforced surface e.g. concrete wall, brick

wall,drywall with wooden studs.The wall bracket is designed to work with standard 16” stud

spacing.This template indicates the proper drill holes and the full, assembled size of the wall

bracket.

Wall Bracket Template

.5"

13mm

.5"

13mm

16"

406mm

203mm

102mm

SupercellWall Bracket Template

#ZBT040001

DrillHere DrillHere

LEVEL THIS LINE

TheCyclone can be rotated in 90-degree increments so that the inlet is facing parallel or

perpendicularto the wall. Decide how you want your system oriented during installation to

bestmeet your shop’s needs. Other positions will not work as they will hinder installation of

theRear Support Brace.

Cyclone Mounting Positions

RIGHTFORWARD LEFT

G24

G22

G17

Filter Hardware

Wall Bracket Hardware

Drum Hardware

Wall Bracket Hardware

Filter Hardware

Oneida Air Systems, Inc.8

Assembly Instructions

1Installing the Bin Gasket (G23) onto the Wall

Bracket (F).

a. Turn the Wall Bracket (F) upside down

[FIG. 1a].

b. Lay out the four Bin Gasket segments

(G23). DO NOT REMOVE THE BACKER

TAPE [FIG. 1b].

c. Arrange the Bin Gasket segments (G23)

in a circle with the ends interlocking and

aligning to the rounded front edge of the

wall bracket [FIG. 1c].

d. Carefully mark a circle around the inside

of the arranged Bin Gasket segments

(G23) with a marker to create a reference

line [FIG. 1d].

e. Peel the backer tape o of the Bin Gasket

segments (G23) and adhere them to the

Wall Bracket (F), lining them up with your

reference line [FIG. 1e].

Note: Press each gasket piece rmly onto the

bracket to ensure a long-lasting, airtight seal.

FIG. 1a FIG. 1b

FIG. 1c

FIG. 1e

FIG. 1d

You will need the following tools:

WALL MOUNTING BRACKET CYCLONE BODY DRUM LATCHES

Stud Finder Light Adhesive Tape 7/16" Wrench 3/8" Wrench

Tack / Center Punch / Nail Tape Measure / Ruler 7/16" Socket Wrench #2 Phillips-Head Screw Driver

Wall Mounting Fasteners * Level 1/2" Wrench

Power Drill Pencil / Marker 1/2" Socket Wrench

Drill Bit (for your wall fastener)

*You will need to supply your own wall mounting hardware. Use appropriate fasteners for the wall type you are

installing your system onto (e.g. lag bolts, drywall anchors, etc.).

G23

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop DC Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V - 2000 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 8491685 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXVM001500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XGK030035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung