Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

2 HP Cyclonic Dust Collector

Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, N.Y. 13204

Ph ne 1-800-732-4065 315-476-5151 Fax 315-476-5044 www. neida-air.c m

Owners Manual

Shown with optional

bolt together Angle

Iron stand.

*Models may

vary sligthly in

appearance.

T905

GORILLA

The

Thank You for Choosing an Oneida Air Systems Product!

OAS manufactures and sells dust collection equipment only. Our qualified technicians and

sales staff are available 7:30am - 6:00pm EST Mon. - Thur. and 7:30am - 5:00pm EST Fri. to

answer any questions concerning OAS products and dust collection. Call for ductwork design

and ductwork quotes, including system pricing and shipping cost.

Table of Contents

Page

Read the entire Owners Manua before insta ing or operating system!

II.

III.

IV.

VI.

VII.

VIII.

IX.

XI.

XII.

XIII.

XIV.

XV.

XVI.

XVII.

System Start-Up Information

Commercial Configurations

General Specifications & Fan Performance Curves

Dimensions

General Assembly

General Assembly Instructions

Bracket Assembly

Filter Assembly

Filter Maintenance

Directions for Cleaning External Filter

Fan / Blower Wiring Diagram

Troubleshooting

Fire Hazards - Read Bef re Installing System

Terms and Conditions

Stand Assembly

Accessories

Fan Motor Maintenance

2HP Super Dust G rilla Owners Manual O.A.S. 2005

I. System Start-Up Information

. Read the installation and maintenance instructions as well as the recommended

safety practices in this manual.

2. Install Ductwork completely before operating collector:

A.) Seal ductwork with silicone sealant or duct tape.

B.) Have Dust Bin in place and sealed.

3. Have licensed electrician wire Fan / Blower according to wire diagram on pg. 2

in this owners manual.

4. Have licensed electrician check current draw on motor with all gates open. Current

draw should not exceed maximum motor amperage. (OAS is not responsible for

damage to motors caused by improper installation, wiring or failure to follow these

directions.)

Caution

The Direct Drive Fan / Bl wer makes the system t p heavy!

Use extreme care when setting the unit up!

Warning

If amperage is t high - shut d wn immediately!

(See tr ublesh ting secti n.)

Warning

D n t perate Fan / Bl wer unless Cycl ne and Dust Bin

are in place. M t r will ver heat!

Warning

Check amperage draw during perati n with all blast gates

pen. Make certain amperage is n t utside perating limit

indicated n m t r plate!

2HP Super Dust G rilla Owners Manual O.A.S. 2005

II. 2 p Dust Gorilla Configurations

Caution:

If exhaust air is vented outside you must provide make up / return air.

Flue gases (carbon monoxide) can be drawn into the shop from furnaces,

water heaters or other appliances.

1. Externa Cartridge Fi ter -

Silencer Included with Filter

1. Externa

Cartridge

Fi ter

2HP Super Dust G rilla Owners Manual

Si encer

inc uded

w/ Fi ter

O.A.S. 2005

Sh wn with

pti nal

Angle Ir n

Stand.

Cartridge Filter Media

Pleated Spun-Bonded Cartridge Filter 39 / 95 Sq. Ft.

Accredited, independent lab tested.

Bathed in teflon-like coating for easy dust release.

Captures 99.9% of Test Material from 0.2 - 2 microns.

III. General Specifications & Fan Performance Curves

- Sleeve kit adds 7 (4 is minimum)

- 35 gal. bin is 22 dia. x 22.5 h / 55 gal. bin is 22 dia. x 35.5 h

- Several Filter Options Available- Galvanized steel construction

- The collector can be hung on the wall, from the ceiling, or free standing support using

the 0 ga. angle iron ring at the top of the cone.

(See assembly instructions)

2.0 hp

Height without

Dust Bin

Cyclone

Diameter

Inlet

Diameter

Weight without

Dust Bin

TEFC

Motors

Class F

0/220v

20.2/ 0. amps

. 5 Service Factor

63 2  7

Approx. Wt.

22 lbs.

w/o drum or filter

Static pressure and volume together determine

a fans performance. Several factors, such as

layout of ductwork and diameter of openings,

can affect a fans performance.

2hp Dust Gori a System

405 max. cfm

Industrial TEFC 2hp motor

5/230v - 23.2/ .5 amps / . 5 Sevice Factor

6 gauge powder painted cyclone & ga. fan housing

7 dia. inlet / 8 rectangular outlet

4.25 dia. x 4 wide cast aluminum fan wheel

back inclined non-sparking, non-ferrous dynamic, two-planed

balanced to ISO 6.3 specifications.

Sound 78 - 79dB @ 0 with Built-in Silencer and Filter

95 Sq. Ft. Filter Media / Spun-Bond

2HP Super Dust G rilla Owners Manual O.A.S. 2005

2hp Super Dust Gorilla Performance Curve

600

400

200

000

800

600

400

200

Air Flow (CFM)

Static Pressure @ Cyclone Inlet

0 2345 7689

405 349

954 779

Ma . CFM = 1405

405

349

954

779

.86

.82

.77

.74

.40

(Output)

CFM

IV. Dimensions

For Minimum Mounting Heights w/ 39 Fi ter.

*Dimensi ns subject t slight variati n in manufacturing.

2HP Super Dust G rilla Owners Manual O.A.S. 2005

Outlet - Can be rotated

independent of the inlet.

Inlet

2 

23

Top View

2 .75

Bolt

Circle

24.5

Outlet

Wall Mounts

3

Cyclone

Barrel

.5

30

2.625

Note: Check drum height, it will

affect your bracket height.

Always check the

actual system

height to

determine your

mounting height.

25. 25

50

2 Flex

22.5 - 35 gal.

34 - 55 gal.

2 Collar

drum

7 Dia.

4 3/ 6

Overall - Minimum 92 (35 Gal.) 03.5 (55 Gal.) This is using only 2 of Flex Hose. The minimum amount.

80 w/ 55 gal. drum

7  w/ 35 gal. drum

To lowest Bracket hole.

35 gal. - 70.5

55 gal. - 79.5

6

Included

Internal

Silencer

39 Filter

50

95 Sq. Ft.

for 9  Min. Height

Rotation

56

V. General Assembly

2HP Super Dust G rilla Owners Manual O.A.S. 2005

Note: For cyclonic preseparation there must be an air tight seal between cyclone and dust

container. Dust bin must be located vertically under cyclone, material drops down by gravity.

Angle Iron Wall

Bracket

supports fan

housing and

cyclone

Cyclone inlet

7 dia.Connect to

main duct run out

to woodworking

machines

Cyclone Preseparator

separates 99% of the

wood waste from the

air stream. Eliminates

wear on the fan wheel

and maintenance on

the filter.

Cone

Flex Hose

Dust Bin

Light weight 35 or 55

gal. fiber dust bin. Steel

drum available for

outside applications.

Hose Clamp

Gasket

Material

Draw

Latches

Silencer

Rod

Brace

Washer

Wing Nut

Dust Pan

Do not

remove foam

from around

wire cage!

This is part of

si encer!

Gasket

Material

Cyclone

Barrel

Industrial TEFC

Motor Fan

Blower

Outlet

Gasket

Material

Clamp

Ring

Clamp

Ring

VI. General Assembly Instructions

2HP Super Dust G rilla Owners Manual O.A.S. 2005

Cyclone

Barrel

Cyclone

Cone

2. Clamp the fan housing and cyclone barrel to the

cyclone cone making sure you cut and put the supplied

gasket material around the top of the cone. Note: the

fan / b ower and the cyc one barre are very heavy.

The system wi be top heavy. Do not try to ift

co ector onto bracket by yourse f. Make sure you

have adequate he p.

3. Lift the collector onto the bracket and orient it into the

preferred position. Bolt each side and back securely

with supplied hardware.

4. Bolt the elbow-cartridge housing to the fan housing

outlet (rectangular), after applying gasket material. Clamp

the cartridge to the flat plate. Clamp the dust bins to the

bottom of the cartridge filters.

Cyclone

Barrel

Air Inlet

Fan / Blower

. Unclamp the blower housing, then cut and place

supplied gasket material around the top of cyclone

barrel, then re-clamp it to match the bracket configuration

and the desired angle for the cyclone inlet that you

choose.

Cycl ne Inlet and Fan / Bl wer are independent.

Filters can be t the right r left f the unit.

Air

Outlet

Gasket

Material

Fan / B ower is shipped c amped to Cyc one Barre .

Do NOT use

hook on motor

to lift unit.

GORILLA

The

Gasket

Material

3/8 Bolt / (2) Washers /

Serrated Nut per bolt hole

on each side and back.

GORILLA

The

Collector

Hose Clamp

Flex Hose

Dust Bin

2 ea. 5/ 6 Serrated Nuts

Clamp Ring

Clamp

Ring

Gasket

Material

GORILLA

The

Clamp

Ring

2HP Super Dust G rilla Owners Manual O.A.S. 2005

VII. Bracket Assembly

. You must determine the direction the fan outlet will point to

proceed with this mounting assembly. The collector will seem

quieter if the outlet is aimed away from the area people tend to

work. Slots in the brackets are .406 x .00

Note: Bolts included to mount bracket to collector. Hardware

NOT included to mount to wall.

2. Hold bracket against wall with top of plate at 56. Mark where

mounting holes fall. Mount wall bracket. For wall mounting, the

bolt centers on the brackets are at 6to accomodate most wall

stud spacing. See Fig. & 2. Use a Level to ensure straightness.

3. Attach bracket to wall with lag screws, concrete anchors, or

other suitable hardware. See Fig. 2 & 3. N te: When installing

the brackets n a c ncrete wall, m unt 2 x 4s between wall and

brackets t stabilize and dampen vibrati n.

4. Position Angle Ring around top of cone over bracket. Line up

one hole in Ring with hole in each bracket at desired rotation of

outlet. If rotation you desire does not correspond to an existing

hole in Angle Ring, drill new ones. Use three 3/8 bolts (included)

with washers & lock washers to secure the fan. See Fig. 4.

5. Attach tightly with bolts. See Fig. 4.

.406 x .00

Note: P ease do not insta an Oneida Dust Co ection System a one. Competent

assistance is advisab e. Units are heavy!

6

2 Ga.

Level

* Optional Mounting Direction

56 to top of plate.

Distance tor minimum

mounting height.

VIII. Filter Assembly

N te: D n t return exhaust air t the sh p unless filter media is added.

External 26 Filter Assembly

. Attach cartridge with hardware provided making sure

gasket is attached. See Fig.

2. If Filter requires additional support. Use the plate at the

top of the filter to support the filter assembly.

Note: If filter cartridge is located away from the cyclone

and motor, additional square-to-round connectors and pipe

can be purchased.

*Silencer Included.

Do not

remove foam

from around

wire cage!

This is part of

si encer!

For Fi ter c eaning instructions, see pg. 11.

Caution:

If exhaust air is vented outside you must provide make up / return air.

Flue gases (carbon monoxide) can be drawn into the shop from furnaces,

water heaters or other appliances.

. Exhaust air to exterior of building.

Mount directly at the hole in exterior

wall or use a square-to-round transition

and ductwork to vent air to exterior.

No Filter Assembly

* Exhaust Diverter -

Can be used either

up or down

Option -

* Only usable on No Filter.

Caution: Rotating b ades! Keep hands c ear. Keep

peop e away from exhaust.

2HP Super Dust G rilla Owners Manual O.A.S. 2005

Fig.

Gasket

Material

Cage

Silencer

Filter

Rod

Brace

Washer

Wing Nut

Dust Bin

GORILLA

The

GORILLA

The

Andere Handbücher für Super Dust Gorilla

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems 10 HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Portable XXP990201H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXVM001500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V - 2000 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK100300 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung