Oneida Air Systems XXVM001500 Bedienungsanleitung

Rev: B 20231025LL Doc. #ZBM000101A

Appearance may vary slightly

OWNER’S MANUAL

V-System

Dust Collector

1.5 HP/ 2 HP / 3 HP

#XXVM001500

EXP-XXVM020139H

#XXVM003000

#XXVM003000W

#XXVM003055

#XXVM003055W

Patents: www.oneida-air.com/patents

Table of Contents

System Start-Up Information 2

System Specications 6

Wall Bracket Dimensions 7

Component Dimensions 8

System Dimensions for V-1500 & 35 Gal. Drum 9

System Dimensions for V-3000 & 35 Gal. Drum 10

System Dimensions for V-3000 & 55 Gal. Drum 11

System Contents 12

Assembly Instructions 14

Maintenance 26

Troubleshooting 27

F.A.Q. 28

Recommended Accessories 30

Warranty Information 32

Notes 33

1oneida-air.com

Oneida Air Systems, Inc.2

System Start-Up Information

 WARNING 

1. READ and understand ALL instructions and warning labels BEFORE using the dust collector.

2. REPLACE warning labels if they become obscured or removed.

3. ALWAYS follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and regulations

when installing and operating this dust collector.

4. ENSURE that all users of this dust collector are informed of all warnings and precautions, safe use, and maintenance

procedures.

5. FULL mental alertness is required. e machine is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge.

6. DO NOT allow use by or near children.

7. DO NOT allow it to be used as a toy.

8. NEVER leave the dust collector running while unattended.

9. TURN OFF and UNPLUG the dust collector BEFORE walking away, servicing, or cleaning. Allow the fan blower motor to

come to a COMPLETE STOP before walking away or performing any maintenance, service, cleaning, or adjustments. is

eliminates the risk of injury from unintended startup or contact with live electrical components.

10. ENSURE that your dust collector is turned OFF and UNPLUGGED during installation. is eliminates the risk of injury

from unintended startup or contact with live electrical components.

11. COMPLETELY INSTALL ductwork/ex hose before operating collector.

a. Seal ductwork with silicone sealant or duct tape if leaks are found.

b. Have dust drum in place and sealed.

c. NEVER operate without lter and cowling in place. is machine has high speed rotating elements than can cause

severe injury.

12. ONLY use the dust collector for its intended purpose as described in this manual. DO NOT force it or an attachment to do a

job for which it was not designed. Consult this owner’s manual or reach out for recommended accessories.

13. ENSURE enough air volume is at the suction point to capture all the particulate generated.

14. NEVER make modications without prior approval from Oneida Air Systems. Modifying the dust collector or using it

dierently than intended will void the warranty and may result in malfunction or mechanical failure that leads to serious

personal injury or death! DO NOT allow use as a toy.

Before Purchasing or installing a dust collection system the process owners/operators

are cautioned to do so in accordance with prescribed Federal, State, Local, OSHA, NFPA,

and any other applicable codes or regulations relating to the type of dust(s) you are

collecting.

This manual contains specific precautionary statements relative to worker safety. Read

thoroughly and comply as directed. The most up to date safety information can be found

on our website: oneida-air.com/safety

oneida-air.com 3

System Start-Up Information (Continued)

15. DO NOT locate or operate the system in moist, wet, poorly lit, or cluttered environments. Operating in these areas can

create shock hazards, increase the risks of accidents and injury, and/or lower the operating lifespan of the dust collector.

16. DO NOT install in classied hazardous atmospheres without an enclosure rated for the application. System location

must account for wind, seismic zone, and other load conditions. Codes may regulate acceptable locations for installing

dust collectors. Consult with the appropriate authorities having jurisdiction to ensure compliance with all national and

local codes regarding dust collector installation. Equipment must be anchored in a manner consistent with local code

requirements. Anchors must be sucient to support dead, live, seismic, and other anticipated loads. Consult a qualied

engineer for nal selection of anchorage.

17. ENSURE exhaust air is properly vented. It should NOT be vented into a wall, a ceiling, or a concealed space of a building.

Personal injury, death, and/or property damage can result from material discharge during venting. e risk of personal

injury and/or property damage can be minimized or avoided by locating vented equipment outside buildings and away

from normally occupied areas. If exhaust air is vented outside, you must provide make up / return air. Flue gases (carbon

monoxide) can be drawn into the shop from furnaces, water heaters, or other appliances.

18. INSPECT and MAINTAIN REGULARLY. Keep the dust collector in proper working order. A machine that isn’t properly

maintained, not working as it should, has been dropped, damaged, le outdoors, or dropped in water could malfunction

leading to serious personal injury or death!

19. AVOID CORD DAMAGE. DO NOT pull or carry by cord. DO NOT use cord as handle. DO NOT unplug by pulling on

cord. To unplug, grab the plug, NOT the cord. DO NOT close door on cord or pull cord around sharp edges or corners. DO

NOT run dust collector over cord. DO NOT handle cord/plug with wet hands. Keep cord away from heated surfaces. If the

supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualied persons in order to

avoid a hazard.

20. ALWAYS check for damaged parts. A part that is damaged should be carefully checked to determine that it will operate

properly and perform its intended function. Immediately repair or replace damaged or mis-adjusted parts before operating

machine.

21. DO NOT put any object in openings. DO NOT use with any opening blocked. (Except when pulsing - See Maintenance

Section for more information.)

22. ALWAYS wear a NIOSH approved respirator when emptying dust bins and during operation. Some dust created by power

sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects

or other long-term respiratory damage.

23. ALWAYS keep hair, loose clothing, ngers, and all parts of body AWAY from openings and moving parts.

24. ALWAYS wear ANSI-approved safety glasses or a face shield when operating or observing machinery and when emptying

dust bin.

25. ALWAYS wear hearing protection during extended periods of operation.

Oneida Air Systems, Inc.4

System Start-Up Information (Continued)

1. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.

2. DO NOT operate the dust collector in areas where explosion risks are high. Areas of high risk include, but are not limited to,

areas near pilot lights, open ames, or other ignition sources.

3. ONLY operate dust collector in locations that include a re suppression system or have a re extinguisher available nearby.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

4. DO NOT allow accumulation of layers of ne dust on horizontal surfaces. Especially overhead lights, electrical boxes and

fuse panels which can ignite dust. Keep the oor around the system clean and free of scrap material, oil, grease.

5. ENSURE all equipment and ductwork is electrically grounded.

6. DO NOT use PVC drain pipe.

7. ALWAYS consult an electrician or qualied service personnel about wiring practices and electrical codes in your area. ONLY

allow an electrician or qualied service personnel to do electrical installation or repair work.

8. ALWAYS disconnect power before accessing or exposing electrical equipment. Improper wiring can cause re, electrocution,

injury, or death.

9. DO NOT use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

10. DO NOT use to pick up liquids, ammable liquids, or combustible liquids, such as gasoline, or use in areas where they may

be present.

11. DO NOT use excessively large wood waste bins. Wood dust mixtures are highly ammable and can be explosive

12. ALWAYS check your dust bin for smoldering materials before leaving the shop.

13. NEVER introduce sparks or sources of ignition into the dust collector. Sparks can be generated in several ways:

a. High speed sanders, abrasive planers, saws, and edgers may strike foreign material and create a red-hot metal fragment.

b. Knots in hardwood can create frictional sparks.

c. Trapped metal, when drawn into the dust collection system, can spark against ductwork.

 FIRE HAZARDS 

Process owners/operators retain all responsibility for the suitability of fire and explosion

hazard mitigation, suppression, and isolation strategies and to follow all applicable

federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and regulations

when installing and operating this dust collector.

Improper operation of a dust control system may contribute to conditions in the work

area or facility that could result in severe personal injury and product or property

damage.

Oneida Air Systems assumes no responsibility or liability for the suitability of any fire and/

or explosion mitigation strategy, or any items incorporated into a collector as part of an

owner/operators hazard mitigation strategy.

oneida-air.com 5

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

System Start-Up Information (Continued)

d. Check wood stock for old nails and screws which can create red-hot metal fragments.

14. DO NOT overload woodworking equipment, especially sanders, as excessive frictional heat can spontaneously ignite dust.

Sanders can produce concentrations of dust well into the combustible range.

15. ALWAYS check that all dust collection equipment is properly selected and sized for the intended use. Authorities with

jurisdiction should be consulted before installing to verify local codes and installation procedures. In the absence of such

codes, install collector according to the National Electric Code, NFPA No. 70-latest edition and NFPA 91, NFPA664 Code

(NFPA 654 if combustible dust is present).

6 Oneida Air Systems

System Specications

OPERATION

Fan Rating (Free Fan) 1.5 HP: 1,518 CFM (2,579 m/hr)

2 HP: 2,940 CFM (4,995.1 m/hr)

3 HP: 2,940 CFM (4,995 m/hr)

Fan Rating (with Cyclone & Filter) 1.5 HP: 1,130 CFM @ 1.8" SP (1,920 m/hr at 46 mmHO )

2 HP: 1,190 CFM at 1.8”SP (2,022 m/hr at 45.7. mmHO )

3 HP: 1,349 CFM @ 2.3" SP (2,292 m/hr at 58 mmHO )

Maximum Suction Rating 1.5 HP: 8.7" HO (221 mmHO)/ 2 HP: 11" HO (279 mmHO) / 3 HP: 13" HO (330 mmHO)

MOTOR AND ELECTRICAL

MotorType U.S. MadeTEFC Motor

Motor Insulation Class F

Motor Service Factor 1.5 HP: 1.15 / 3 HP: 1.0

Horsepower 1.5 HP (1.1 kW)/ 2 HP (1.5 kW) / 3 HP (2.2 kW)

Motor Speed 3,450 RPM

Phase Single-Phase (1ph)

Voltage 1.5 HP: 110V / 2 & 3 HP: 220V

Cycle 60Hz / 2HP: 50Hz

Listed FLA 1.5 HP: 8 / 2 HP: 8.6 / 3 HP: 13

On/O Switch Magnetic Starter with On-O Switch

Preset for Included Remote

Power Cord 10 ft (3 m)

Power Plug Included 1.5 HP: NEMA 5-15 / 2 HP: BareWiring / 3 HP: NEMA 6-20

Recommended Circuit Size 20A

Recommended Circuit Type HACR

Sound Emission With Stacking Sound Filter: 72 - 76 dBA @ 10 ft (3 m)

IMPELLER

Size 1.5 HP: 12" (305 mm) Diameter / 2 & 3 HP: 15" (381 mm) Diameter

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter MediaType G.E. H12 HEPA

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 95 Sq. Ft. (8.83 sq m)

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Molded Static Conductive Resin

Inlet 7" (177.8 mm) Diameter

Overall Height (with 35 Gallon Drum) 1.5 HP: 87" (2,209.8 mm) / 3 HP: 88" (2,235.2 mm)

OverallWeight 1.5 HP: 189 lbs (85.7 kg) / 3 HP: 202 lbs (91.6 kg)

18in systems dimensions

3/4"

19 mm

16"

406 mm

14"

356 mm

Note: e Wall Bracket is universal to 18" and 21" systems. e blackened holes on the Back

Support Brace and Le and Right Wall Brackets in the images above will not be utilized in

the V-System installation.

14-3/4"

375 mm

10-1/4"

262 mm

1/4"

8 mm

20-1/4"

516 mm

Left Wall Bracket Right Wall Bracket

Back Support Brace

3-1/4"

83 mm

7oneida-air.com

Wall Bracket Dimensions

8Oneida Air Systems

26"

661 mm

13-1/2"

344 mm

40"

1,016 mm

6-3/4"

171 mm

152 mm

17-3/8"

442 mm

14-9/16"

370 mm

12-5/16"

313 mm

17-1/4"

438 mm

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

Component Dimensions

23"

584 mm

35 Gallon

55 Gallon

35"

889 mm

22-1/4"

565 mm

23"

584 mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V - 2000 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Gorilla XXP999901 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Portable XXP990201H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK050100 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Pro XXS200001 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini GORILLA XXP010101 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung