Oneida Air Systems XXK100300 Bedienungsanleitung

10 HP

Direct Drive

Dust Collectors

Owner’s Manual

9_11

Oneida Air Systems, Inc. 1001 West Fayette St., Syracuse, NY 13204

Phone 1.800.732.4065 315.476.5151 Fax 315.476.5044 www.oneida-air.com

ZBM000017

10hp Direct Drive © O.A.S. 2010

Thank You for Choosing an Oneida Air Systems Product!

OAS manufactures and sells dust collection equipment only. Our qualied technicians and sales staff

are available 7:30am - 6:00pm EST Mon. - Thurs. and 7:30am - 5:00pm EST Fri. to answer any ques-

tions concerning OAS products and dust collection. Call for ductwork design and ductwork quotes,

including system pricing and shipping cost.

Read the entire Owner’s Manual before installing or operating system!

Proudly

Made in

the USA

II.

III.

IV.

VI.

VII.

VIII.

IX.

XI.

XII.

XIII.

XIV.

XV.

XVI.

XVII.

7 - 8

18 - 20

System Start-Up Information

General Assembly

General Specications & Fan Performance Curve

Dimensions

Stand Assembly

General Assembly Instructions

Fan / Blower Maintenance

Congurations

Filter Maintenance

Wire Diagram

Accessories

Troubleshooting

Fire Hazards - Read Before Installing System

Terms and Conditions

Filter Efciency Gauge Instructions

Fan Motor Lunbrication

Supplemental Instructions for Magnetic Motor Starters

Table of Contents Page

10hp Direct Drive © O.A.S. 2010

I. System Start-Up Information

Caution

Warning

1. Read the installation and maintenance instructions as well as the recommended safety practices in

this manual.

2. Install Ductwork completely:

(A.) Seal ductwork with silicone sealant or duct tape.

(B.) Have Dust Bin in place and sealed.

3. Have licensed electrician wire Fan / Blower according to wire diagram in this owner’s manual.

4. Have a licensed electrician check current draw on motor with all gates open. Current draw should not

exceed maximum motor amperage. (OAS is not responsible for destroyed motors.)

The Dust Collector & Fan / Blower is heavy! Handling and installation

should always be performed by experienced and trained personnel who

have experience with rotary equipment. In addition to the following instruc-

tional manual, care should be taken to ensure compliance with specic

safety requirements mandated bt federal, state and local codes.

Do not operate Fan / Blower without connecting ductwork. Never oper-

ate Fan / Blower without belt shaft guard in place. Keep clear of exhaust.

Keep hands and objects clear of inlet and outlet.

Check amperage draw during operation with all blast gates open. Make

certain amperageis not outside operating limit indicated on motor plate!

If amperage is too high - shut down immediately! (See Troubleshooting

section.)

10hp Direct Drive © O.A.S. 2010

II. General Assembly - XXK100300 - 3 Phase

10hp Direct Drive System - XXK010300 3 phase

1. Motor Blower Assembly - BXI050100 - 1ph - BXI070300 - 3ph

1a. Motor - 1ph / BMZ070370 - 7.5hp 3 ph

1b. Fan Housing - BHX070000

1c. Fan Wheel - BWX179800

1d. 7.5hp shaft spacer - BBS070001

1e. Bolt 5/16” - 24 x 1” left thread - AFB155160

1f. Motor Plate - RMP000000

1g. 5/16” Washer - AFW155160

1h. Bolt 1/2” - 13 x 3/4” HH (4) AFB155200

1i. Lockwasher 1/2” (4) - AFL010500

1j. Fender Washer 5/16” x 1 1/2” (2) - AFW170000

1k. Washer Flat 3/8” (8) - AFW190000

1l. Whiz Lock Nut 3/8” GR5 (4) - AFT000004

1m. Bolts 3/8” - 16 x 1” HHGR (4) - AFS015100

2. Cyclone Barrel - SXI070000

3. Cyclone Cone - SCX070000

4. Bolts 3/8” 16 x 1” (16) - AFS015100

Washers 3/8” (32) - AFW190000

3/8” Wiz Lock Nuts (16) - AFT000004

5/16” Wiz Lock Nuts (16) - AFT155175

5. Neoprene Gasket (30”) - RGZ000000

6. Owner’s Manual - ZBM000017

7. Plenum Filter Assembly - FXK020100

7a. Plenum Assembly 3 Filters - FPX020700

7b. Dust Bin 18” (3) - FPZ000018

7c. Filter Cartridge 130 sq. ft. 18” dia. x 62” L (3) - FCS186200

7d. Internal Silencer (3) - BSC180000

8. Filter Efciency Gauge Kit - FXK000000

8a. Fil. Eff. Gauge - VRG001005

8b. Vinyl Tubing (8’) - VRV003125

8c. Static Pressure Tip - VRP001875

8d. Mounting Flange for Pitot Tube - VRP010000

8e. Gauge Bracket - FXX000000

9. 55 gal. Steel Drum Kit - SEK551001

9a. Drum Lid w/ 10” ring - SEX55100

9b. Hose Clamps (2) - ACB120000

9c. 55 gal. Steel Drum - SES550000

9e. Flex Hose (10” dia. x 1’) - DHF100000

10. Stand with Plenum Support - STZ070000

10hp Direct Drive © O.A.S. 2010

III. General Specications & Fan Performance Curves

Physical and Electrical Data for 10hp Direct Drive Systems

System Performance Dust Bin

Sound

System Dimensions

Integral Fan Blower - 10hp External Cartridge Filter

Fan Wheel Diameter: 17” Welded Carbon Steel

Cyclone Inlet: 12”

TEFC 60 Hz Motor - Single Phase

Insulation Class: F4

Voltage: 208 - 230/460 3 Phase

Amperage: 26.2 - 23.8 / 11.9

Made in U.S.A.

3 Pleated Cartridge - 390 Sq. Ft.

Spun-Bonded polyester BIA ZH1/487 test - Rated C

Captures 99.99% of test material over 20 microns

Captures 99,9% of test material between 0.2 - 2

microns @ 11 fpm

10hp - 3800 cfm @ 2.3” SP no lter 55 Gal. Steel Drum

Large Dust Bins available

w/ Filters but no Internal Silencers:

85 - 87dBA @ 10’

10hp Direct Drive © O.A.S. 2010

IV. Dimensions For minimum mounting heights with 55 gal. drum

115.9

10hp Direct Drive © O.A.S. 2010

V. Angle Iron Stand

10hp Direct Drive © O.A.S. 2010

VI. Assembly Instructions

10hp Direct Drive © O.A.S. 2010

VI. Assembly Instructions (Cont.)

Wait a few minutes

for internal dust to

settle then unscrew

thumb nuts from

J-Hooks and remove

dust bin. Empty dust

carefully. Replace

dust bin. Do not over

tighten thumb nuts.

Filter

J-Hook

Dust Bin

Thumb Nut

Drum Grounding Wire

To attach the Drum

Grounding Wire, start a

small hole in bottom of

cone above ex hose

and in the top of the

dust drum, then attach

the wire with the 3/8”

included self-tapping

screws.

5. Attach ex hose to bot-

tom of collector and to lid

of dust bin. Securely fas-

ten hose clamps. There

must be an air tight seal

between the collector and

dust bin.

6. Make sure the dust bin lid sits se-

curely and the rubber gasket on the bin

lid is in place on the barrel. Maintain an

air tight seal between cyclone and dust

bin to prevent motor from overheating.

7. Attach the ductwork from the wood-

working machines to the inlet of the

collector.

8. On external lter models, attach the

Plenum Assembly or connect to your

own plenum box.

9. Attach feet of Angle Iron stand to the

oor.

Note: Assembly with tube lters - Note plenum

height requirements of tube lters - 6’ tubes - 8’ ple-

num / 8’ tubes - 10’ plenum / 10’ tubes - 12’ plenum.

Adjust system height accordingly.

10hp Direct Drive © O.A.S. 2010

VII. Fan / Blower Maintenance

A high pressure blower requires a certain amount of resistance which will prevent motor over amperage.

Make sure power source matches wire voltage congurations.

Check set screw and key in fan wheel, make sure fan wheel is secure. Fan blower should not vibrate.

1. Electical - Failure to follow instructions and safe electrical procedures could result in serious injury or death. Discon-

nect all power and discharge all capacitors before servicing. Install and ground per local and national codes. Consult a

licensed electrician with questions or if repairs are required.

Electrical Connections_

A.) All wiring, fusing, and grounding must comply with National Electrical Codes and local codes.

B.) To determine proper rotation and voltage connections, refer to the wire diagram of this manual.

C.) Use the proper size of line current protection and motor controls as required by the National Electrical Code and local

codes. Recommended use is 125% of full load amps as shown on the nameplate for motors with 40 degrees celsius

ambient and a service factor over 1.0. Recommended use is 115% of full load amps as shown on nameplate for all other

motors. Do not use protection with larger capacities than recommended. Three phase motors must have all three phases

protected.

2. Cleanliness - Keep both the interior and exterior of the motor free from dirt, water, oil, and grease.

4. Service - Notice - If lubrication instructions are shown on the motor nameplate, they will supercede this general

instruction.

3. Safety- Motors should be installed, protected and fused in accordance with the latest issue of National Electrical

Code, NEMA Standard Publication No. 2 MG 2 and local codes. Rotating parts such as pulleys, coupling, external fans,

and unusual shaft extentions should be permanently guarded. Keep hands and clothing away from moving parts. Elec-

trical repairs should be made by trained, qualied personnel only.

Warning! Rotating Fan Blades. Keep Objects Clear of Inlet and Outlet!

VIII. Fan / Blower Maintenance

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXS050333 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V - 2000 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2005c3HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini GORILLA XXP010101 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Pro XXS200001 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK050100 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung