Oneida Air Systems V1500 Bedienungsanleitung

Rev: 11/20/2019 Doc. #ZBM000101A

Appearance may vary slightly

U.S. Patent 8377160, 9370740,

8514090, 8496719, 7247180

OWNER’S MANUAL

V-System

Dust Collector

1.5 HP/3 HP

#XXVM001500

#XXVM003000

#XXVM003000W

#XXVM003055

#XXVM003055W

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 4

System Dimensions for V1500 and 35 Gal.

Drum 5

System Dimensions for V-3000 and 35 Gal.

Drum 6

System Dimensions for V-3000 and 55 Gal.

Drum 7

System Contents 8

Assembly Instructions 10

Maintenance 18

Troubleshooting 19

Recommended Accessories 20

Warranty Information 22

2 Oneida Air Systems

System Start-Up Information

1. Install ductwork completely before operating collector.

a. Seal ductwork with silicone sealant or duct tape.

b. Have dust drum in place and sealed.

2. DO NOT operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place. Dust Drum and

Cyclone must be in place and sealed or motor will overheat!

3. DO NOT operate without lter in place. Fan blade can cause serious injury.

4. e Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! It is recommended

that at least two people li the system up.

5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated

on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or

failure to follow these directions).

6. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

7. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

8. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

9. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deagrate

(burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame

front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise

additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been

witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

Make sure to read and understand the installation and maintenance instructions as well as all

recommended safety practices.



3oneida-air.com

System Start-Up Information (Continued)

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Personnel should be kept at least 20 . away from unit.

9. Check dust bin for smoldering material frequently and before leaving the shop.

10. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

11. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

12. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

13. Empty dust bin and clean lter oen, especially when sanding.

14. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

15. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Tramp metal when drawn into the collector can spark against ductwork.

e. Check wood stock for old nails and screws which can create red hot metal fragments.

16. Avoid using excessively large wood waste bins.

17. ALWAYS check storage bins for smoldering material before leaving for the day.

18. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

19. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

20. UNPLUG UNIT BEFORE SERVICING OR CLEANING

OAS Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4 Oneida Air Systems

System Specications

OPERATION

Fan Rating (Free Fan) 1.5 HP: 1,518 CFM (2,579.1 m/hr)

3 HP: 2,940 CFM (4,995.1 m/hr)

Fan Rating (with Cyclone & Filter) 1.5 HP: 949 CFM @ 1.8" SP (1,612.4 m/hr at 45.7 mmHO )

3 HP: 1349 CFM @ 2.3" SP (2,292 m/hr at 58.4. mmHO )

Maximum Suction Rating 1.5 HP: 8" HO (203 mmHO)/ 3 HP: 8" HO (203 mmHO)

MOTOR AND ELECTRICAL

MotorType U.S. MadeTEFC Motor

Motor Insulation Class F

Motor Service Factor 1.5 HP: 1.15 / 3 HP: 1.0

Horsepower 1.5 HP (1.1 kW)/ 3 HP (2.2 kW)

Motor Speed 3,450 RPM

Phase Single-Phase (1ph)

Voltage 1.5 HP: 110V / 3 HP: 220V

Cycle 60Hz

Listed FLA 1.5 HP: 8 / 3 HP: 13

On/O Switch Magnetic Starter with On-O Switch

Preset for Included Remote

Power Cord 10 ft (3 m)

Power Plug Included 1.5 HP: NEMA 5-15 / 3 HP: NEMA 6-20

Recommended Circuit Size 20A

Recommended Circuit Type HACR

Sound Emission With Stacking Sound Filter: 72 - 76 dBA @ 10 ft (3 m)

IMPELLER

Size 1.5 HP: 12" (305 mm) Diameter / 3 HP: 15" (381 mm) Diameter

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter MediaType G.E. H12 HEPA

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 95 Sq. Ft. (8.83 sq m)

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Molded Static Conductive Resin

Inlet 7" (177.8 mm) Diameter

Overall Height (with 35 Gallon Drum) 1.5 HP: 87" (2,209.8 mm) / 3 HP: 88" (2,235.2 mm)

OverallWeight 1.5 HP: 189 lbs (85.7 kg) / 3 HP: 202 lbs (91.6 kg)

5oneida-air.com

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

System Dimensions for V1500 and 35 Gal. Drum

Top View

1.5 HP

87"

2210 mm

13"

330 mm

75"

1905 mm

30"

762 mm

27"

686 mm

203 mm

56"

1422 mm

63"

1600 mm

25"

635 mm

14"

356 mm

36"

914 mm

30"

762 mm

32-1/2”

762 mm

47"

1194 mm

6 Oneida Air Systems

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

System Dimensions for V-3000 and 35 Gal. Drum

Top View

13"

330 mm

47"

1194 mm

75"

1905 mm

30"

762 mm

27"

686 mm

203 mm

56"

1422 mm

63"

1600 mm

25"

635 mm

14"

356 mm

36"

914 mm

88"

2235 mm

30"

762 mm

32-1/2”

762 mm

7oneida-air.com

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

System Dimensions for V-3000 and 55 Gal. Drum

Top View

13"

330 mm

87"

2210 mm

30"

762 mm

27"

686 mm

203 mm

68"

1727 mm

75"

1905 mm

25"

635 mm

14"

356 mm

36"

914 mm

99"

2515 mm

30"

762 mm

32-1/2"

762 mm

10"

254 mm

47"

1194 mm

8 Oneida Air Systems

System Contents

* ere will be leover gasket

†Additional parts are included in your hardware

package (AHX000005).

‡Combined inside hardware package (AHX000516).

ID Part number Part description Qty

A BXI010107

BXI030107A

Motor Assembly 1.5 HP 1PH

Motor Assembly 3 HP 1PH

B BHX020005B Fan Housing 1

C SXI002107 Barrel 1

D SCX002107B Cone 1

E SEX550700 Steel Drum Lid

with 7" Collared Lid 1

FSES350000

SES550000

35 Gallon Steel Drum with Clamp

55 Gallon Steel Drum with Clamp 1

G AHX180002 V-System Accessory Pack 1

G1 ACB080000 6"-8" Clamp Band 2

G2 DHF070001 7" Diameter Flex Hose 1

G3 STX180003 Plenum Support Brace 1

G4 AHX000003C V-System Hardware Kit 1

G4A* RGZ000000 Neoprene Foam Gasket Roll 25'

G4B RGZ125075 Gasket Roll 6'

G4C AFT051618A Pack of eight 5/16-18" U-Spring Nuts 1

G4D† AFB155114 5/16-18" x 1.25" Flange Bolt 46

G4E† AFT155175 5/16"Whiz-Lock Nut 46

G4F‡ AFT900516 5/16-18" Nylock Nut 8

G4G‡ AFW180000 5/16" FlatWasher 8

G4H FGA000002 14" Grounding Cable withTwo 8-18 x

3/8”Self-tapping Screws 1

ID Part number Part description Qty

H FCS133695HF 13" x 36" HEPA Cartridge Filter 1

I GXF010013 13" Plenum Kit 1

I1 FPX000001 Filter Plenum Elbow 1

I2 FPX010013 13" Filter Plate 1

I3 BSC130000 Drop-in Silencer 1

I4 FPZ000013 Fine Dust Bin 1

I5 AHX001318 Plenum Hardware Kit 1

I5A AFJ051602 5/16-18" x 2" J Bolt 8

I5B AFT000001 5/16-18"Thumb Nut 8

I5C AFB516125 5/16-18" x 1.25" Bolt 9

I5D AFW180000 5/16" FlatWasher 9

I5E AFT155175 5/16-18"Whiz-Lock Nut 9

JSTZ180001

SMS1800000B

Stand

Wall Bracket 1

K BSS131400 13" Dia. Stacking Sound Filter 1

L AMR000000 Remote 1

M AXB999110B Dust Sentry 1

You will need the following tools:

GENERAL FAN HOUSING FILTER

8" Ladder Razor Knife Flathead Screwdriver 7/16"Wrench

Level Diagonal Cutters Hammer 7/16" SocketWrench

Scissors Tape Measure / Ruler

1/2"Wrench 1/4" Socket

1/2" SocketWrench Impact Driver

If you cannot find an item on the list, examine the packaging materials very carefully.

Certain components have been pre-installed. *There may be hardware leftover.

Andere Handbücher für V1500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Portable XXP990201H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XGK030035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXS050333 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop DC Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK100300 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000014 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Pro XXS200001 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung