Oneida Air Systems XCKM013000 Bedienungsanleitung

Rev: A 20230614LL Doc. #ZBM000064

Appearance may vary slightly

Patents: www.oneida-air.com/patents

OWNER’S MANUAL

Dust Cobra

Dust Collector

Industrial

30/35 Gallon Freestanding

#XCKM013000

#XCKM013511

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 6

System Dimensions 8

System with Dolly and Stand Dimensions 9

System Contents 10

Assembly Instructions 12

Maintenance 23

Troubleshooting 25

Warranty Information 26

Recommended Accessories 27

Recommended Accessories 28

Notes 29

Oneida Air Systems, Inc.2

System Start-Up Information

 WARNING 

1. READ and understand ALL instructions and warning labels BEFORE using the dust collector.

2. REPLACE warning labels if they become obscured or removed.

3. ALWAYS follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and

regulations when installing and operating this dust collector.

4. ENSURE that all users of this dust collector are informed of all warnings and precautions, safe use, and

maintenance procedures.

5. FULL mental alertness is required. e machine is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and knowledge

6. DO NOT allow use by or near children.

7. DO NOT allow to be used as a toy.

8. NEVER leave the dust collector running while unattended.

9. TURN OFF and UNPLUG the dust collector BEFORE walking away, servicing, or cleaning. Allow the fan

blower motor to come to a COMPLETE STOP before walking away or performing any maintenance, service,

cleaning, or adjustments. is eliminates the risk of injury from unintended startup or contact with live

electrical components.

10. ENSURE that your dust collector is turned OFF and UNPLUGGED during installation. is eliminates the

risk of injury from unintended startup or contact with live electrical components.

11. COMPLETELY INSTALL ductwork/ex hose before operating collector.

a. Seal ductwork with silicone sealant or duct tape if leaks are found.

b. Have dust drum in place and sealed.

c. NEVER operate without lter and cowling in place. is machine has high speed rotating elements than

can cause severe injury.

12. ONLY use the dust collector for its intended purpose as described in this manual. DO NOT force it or

an attachment to do a job for which it was not designed. Consult this owner’s manual or reach out for

recommended accessories.

13. ENSURE enough air volume is at the suction point to capture all the particulate generated.

Before Purchasing or installing a dust collection system the process owners/operators

are cautioned to do so in accordance with prescribed Federal, State, Local, OSHA, NFPA,

and any other applicable codes or regulations relating to the type of dust(s) you are

collecting.

This manual contains specific precautionary statements relative to worker safety. Read

thoroughly and comply as directed. The most up to date safety information can be found

on our website: oneida-air.com/safety

oneida-air.com 3

System Start-Up Information (Continued)

14. NEVER make modications without prior approval from Oneida Air Systems. Modifying the dust collector

or using it dierently than intended will void the warranty and may result in malfunction or mechanical

failure that leads to serious personal injury or death!

15. DO NOT locate or operate the system in moist, wet, poorly lit, or cluttered environments. Operating in these

areas can create shock hazards, increase the risks of accidents and injury, and/or lower the operating lifespan

of the dust collector.

16. DO NOT install in classied hazardous atmospheres without an enclosure rated for the application. System

Location must account for wind, seismic zone, and other load conditions. Codes may regulate acceptable

locations for installing dust collectors. Consult with the appropriate authorities having jurisdiction to ensure

compliance with all national and local codes regarding dust collector installation. Equipment must be

anchored in a manner consistent with local code requirements. Anchors must be sucient to support dead,

live, seismic, and other anticipated loads. Consult a qualied engineer for nal selection of anchorage.

17. ENSURE exhaust air is properly vented. It should NOT be vented into a wall, a ceiling, or a concealed space

of a building. Personal injury, death, and/or property damage can result from material discharge during

venting. e risk of personal injury and/or property damage can be minimized or avoided by locating vented

equipment outside buildings and away from normally occupied areas. If exhaust air is vented outside, you

must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop from furnaces,

water heaters, or other appliances

18. INSPECT and MAINTAIN REGULARLY. Keep the dust collector in proper working order. A machine that

isn’t properly maintained, not working as it should, has been dropped, damaged, le outdoors, or dropped in

water could malfunction leading to serious personal injury or death!

19. AVOID CORD DAMAGE. DO NOT pull or carry by cord. DO NOT use cord as handle. DO NOT unplug

by pulling on cord. To unplug, grab the plug, DO NOT close door on cord or pull cord around sharp edges or

corners. DO NOT run dust collector over cord. DO NOT handle cord/plug with wet hands. Keep cord away

from heated surfaces.

20. ALWAYS check for damaged parts. A part that is damaged should be carefully checked to determine that

it will operate properly and perform its intended function. Immediately repair or replace damaged or mis-

adjusted parts before operating machine.

21. DO NOT put any object in openings. DO NOT use with any opening blocked. (Except when pulsing - See

Maintenance Section for more information.)

22. ALWAYS wear a NIOSH approved respirator when emptying dust bins and during operation. Some dust

created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals

known to cause cancer, birth defects or other long-term respiratory damage

23. ALWAYS keep hair, loose clothing, ngers, and all parts of body AWAY from openings and moving parts.

24. ALWAYS wear ANSI-approved safety glasses or a face shield when operating or observing machinery and

when emptying dust bin.

25. ALWAYS wear hearing protection during extended periods of operation.

Oneida Air Systems, Inc.4

System Start-Up Information (Continued)

1. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.

2. DO NOT operate the dust collector in areas where explosion risks are high. Areas of high risk include, but

are not limited to, areas near pilot lights, open ames, or other ignition sources.

3. ONLY operate dust collector in locations that include a re suppression system or have a re extinguisher

available nearby.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire

Extinguishers).

4. DO NOT allow accumulation of layers of ne dust on horizontal surfaces. Especially overhead lights,

electrical boxes and fuse panels which can ignite dust. Keep the oor around the system clean and free of

scrap material, oil, grease.

5. ENSURE all equipment and ductwork is electrically grounded.

6. DO NOT use PVC drain pipe.

7. ALWAYS consult an electrician or qualied service personnel about wiring practices and electrical codes

in your area. ONLY allow an electrician or qualied service personnel to do electrical installation or repair

work.

8. ALWAYS disconnect power before accessing or exposing electrical equipment. Improper wiring can cause

re, electrocution, injury, or death.

9. DO NOT use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

10. DO NOT use to pick up liquids, ammable liquids, or combustible liquids, such as gasoline, or use in areas

where they may be present.

11. DO NOT use excessively large wood waste bins. Wood dust mixtures are highly ammable and can be

explosive

 FIRE HAZARDS 

Process owners/operators retain all responsibility for the suitability of fire and explosion

hazard mitigation, suppression, and isolation strategies and to follow all applicable

federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and regulations

when installing and operating this dust collector.

Improper operation of a dust control system may contribute to conditions in the work

area or facility that could result in severe personal injury and product or property

damage.

Oneida Air Systems assumes no responsibility or liability for the suitability of any fire and/

or explosion mitigation strategy, or any items incorporated into a collector as part of an

owner/operators hazard mitigation strategy.

oneida-air.com 5

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

System Start-Up Information (Continued)

12. ALWAYS check your dust bin for smoldering materials before leaving the shop.

13. NEVER introduce sparks or sources of ignition into the dust collector. Sparks can be generated in several

ways:

a. High speed sanders, abrasive planers, saws, and edgers may strike foreign material and create a red-hot

metal fragment.

b. Knots in hardwood can create frictional sparks.

c. Trapped metal, when drawn into the dust collection system, can spark against ductwork.

d. Check wood stock for old nails and screws which can create red-hot metal fragments.

14. DO NOT overload woodworking equipment, especially sanders, as excessive frictional heat can

spontaneously ignite dust. Sanders can produce concentrations of dust well into the combustible range.

15. ALWAYS check that all dust collection equipment is properly selected and sized for the intended use.

Authorities with jurisdiction should be consulted before installing to verify local codes and installation

procedures. In the absence of such codes, install collector according to the National Electric Code, NFPA No.

70-latest edition and NFPA 91, NFPA664 Code (NFPA 654 if combustible dust is present).

6Oneida Air Systems

System Specications

OPERATION

Fan Rating (Free Fan) 245CFM

Fan Rating (with Cyclone & Filter) 245 CFM @ 23" WC - Maximum Flow Rate

202 CFM @ 34" WC - with 25’of 2.5"diameter ex hose

Maximum Suction Rating 70" WC

MOTOR AND ELECTRICAL

Motor Type UL listed Industrial motor

Voltage 110V

Amperage 15.5A

Power Cord Length 20'

Power Plug Included Yes

Power Plug Type 110V: NEMA

Recommended Circuit Size 20A

Sound Emission With Standard Silencer & Filter: 73 dBA @ 10 ft

CARTRIDGE FILTER

Filter Type GORE Cleanstream® HEPA Filters

Filter Rating 99.97% ltration eciency at 0.3 microns (µm)

Pulse Type Manual Internal Rapid Pulse Filter Cleaner System

Pulse Interval ~30 Minutes or as needed based on the situation

SYSTEM DIMENSIONS AND CONSTRUCTION

Cyclone Body Industrial, Static Conductive Resin

Inlet Size 2.5" O.D. (2.25" I.D.)

Inlet Dimensions 2.3" ID

Drum Type Reinforced Steel Drum with Painted Exterior

Container Size 30 Gallons/35 gallons

Overall Height 30 Gallon: 53.5" / 35 Gallon: 59.25"

7oneida-air.com

System Specications

WARNING

This motor can expose you to chemicals,

including carbon black, which is known to

the State of California to cause cancer.

For more information go to

www.P65Warnings.ca.gov

Keep the Certicate of Compliance on hand while doing lead remediation

8Oneida Air Systems

System Dimensions

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

52-3/16"

1,326 mm

34-1/2"

875 mm

39-1/2"

1,002 mm

54-3/16"

1,376 mm

30 Gallon:

29-9/16"

751 mm

35 Gallon:

22-1/4"

565 mm

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 8491685 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini GORILLA XXP010101 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000014 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2 HP Commercial Cyclonic Dust Collector Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung