Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Appearance may vary slightly.

9_11

ZBM000101

Powerful Economical Made in the USA

Oneida Air Systems, Inc. was founded in 1993 to bring cost effective, state-of-the-art

dust collection systems and material handling ductwork to woodworking shops. OAS

designs and manufactures industrial grade dust collection systems that create a prac-

tical, safe and healthy work place environment.

1.800.732.4065 www.oneida-air.com

1001 W. Fayette St., Syracuse, NY 13204

V-SYSTEMS

TM TM TMTM

V-Systems 3000

“With the smoothest-running

impeller, best overall t and

nish, and superior dust l-

tration, this 3-hp cyclone was

the cream of the crop. Another

plus: it’s the second quietest,

below the threshold of poten-

tial hearing loss (85 dB).”

WOOD® Magazine - May 2013

In WOOD Magazine’s (May 2013)

Air Quality Test the Oneida V-Sys-

tem dust collector was the best at

keeping airborn dust levels lowest

in the wood shop.

Oneida Air Systems is #1

at Collecting Dust!

U.S. Pat. #

8,377,160

Filter Flame Guard

Arrestor - U.S.

Pat. # 8,496,719

V - Systems Owner’s Manual O.A.S. 2010

Thank You for Choosing an Oneida Air Systems Product!

OAS manufactures and sells dust collection equipment only. Our qualied technicians and sales staff are available

8:30am - 5:00pm EST Mon. - Fri. to answer any questions concerning OAS products and dust collection. Call for duct-

work design and ductwork quotes, including system pricing and shipping cost.

Read the entire Owner’s Manual before installing or operating system!

Proudly Made

in the USA

II.

III.

IV.

VI.

VII.

VIII.

IX.

XI.

XII.

6 - 9

System Start-Up Information

System Contents

System Specications

Stand Assembly

System Assembly

Directions for Cleaning Filter

Electrical Data

Troubleshooting

Fire Hazards - Read Before Installing System

Terms and Conditions

Fan Motor Maintenance

Wall Mount Assembly (Optional)

Table of Contents Page

For Customer Service:

866 - 387 - 8822 or [email protected]

I. System Start-Up Information

V - Systems Owner’s Manual O.A.S. 2010

1. Read the installation and maintenance instructions as well as the recommended safety practices in this

manual

2. Install ductwork completely before operating collector:

A.) Seal ductwork with silicone sealant or duct tape.

B.) Have dust bin in place and sealed.

Caution

The Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit

up! It is recommended that at least two people lift the system up.

Warning

Do not operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in

place. Dust Drum and Cyclone must be in place and sealed or motor will overheat!

Warning

Check amperage draw on motor with all gates open. Current draw should not exceed maximum

motor amperage as stated on motor plate. (OAS is not responsible for damage to motors caused by

improper installation, wiring or failure to follow these directions.)

V - Systems Owner’s Manual © O.A.S. 2010

II. System Contents

SCX002107A /

SCX002108A

RGZ000000 - 25 ft.

AFT051618 - 8

AFW190000 - 14

AFS013000 - 2

AFW180000 - 9

AFB516125 -9

AFJ051602 - 8

AFT000001 - 8 AFT155175 - 9

AFB155155 - 16

AFB155190 - 6

AFS015100 - 7

AFT000004 - 7

AFT155175 - 6

AFW180000 - 12

BXI010107 - 1.5hp

BXI002105 - 2hp

BXI030107 - 3hp

BXI012305 - 5hp

BXH020005B

FCS133695HF

BSC130000

FPZ000013

SDS350000

SDX000700

V - Systems Parts List

ACB080000

DHF070000

FPX000001 FPX010013

BHX020005B Fan Housing -1

FCS133695HF Filter 13”x 36” - 1

BXI030107 3hp Motor Assembly - 1

SCX002107A / SCX002108A Cyclone - 1

SDS350000 35 Gal. Fiber Drum & Clamp -1

SDX000700 Drum Lid -1

DHF070000 Flex Hose 7” Dia. -1 ft.

ACB080000 6 - 8” Clamps -2

FPX010013 13” Filter Plate - 1

FPX000001 Plastic Plenum - 1

FPZ000013 Plastic Dust Bin - 1

BSC130000 Filter Silencer - 1

AFB516125 5/16 Carriage Bolt - 9

AFJ051602 J Bolts - 8

AFT000001 Thumb Nut - 8

AFT155175 5/16 Whiz Nut - 9

AFW180000 5/16 Washer - 12

AFB155155 5/16 Flange Bolt - 16

AFS015100 3/8 Hex Head Bolt - 7

AFT000004 3/8 Whiz Nut - 7

AFT051618 U-Spring Nut - 8

AFW190000 3/8 Washer - 14

RGZ000000 Gasket 25 ft.

FGA000001 Drum Grounding Wire - 1

AFS013000 3/8” Self-Tapping Screw - 2

For Stand Contents see

Pg. 5 of the manual.

System Hardware Kit -

AHX000003A

Plenum Hardware

FGA000001 - 1

V - Systems Owner’s Manual © O.A.S. 2010

III. System Specications

Oneida V-1500™ 1.5hp /V -2000™ 2hp / V-3000™ 3hp / V-5000™ 5hp

Part # Description

XXV010139H

XXV020139H

XXV030139H

XXV050139H

V-1500™ Collector

V-2000™ Collector

V-3000™ Collector

V-5000™ Collector

Performance: V-2000™

6 inch pipe 1080 CFM @ 2.5” W/C SP

5 inch pipe 913 CFM @ 4.5” W/C SP

4 inch pipe 760 CFM @ 6.3” W/C SP

3 inch pipe 560 CFM @ 8.1” W/C SP

0 CFM @ 10.5” W/C SP

Performance: V-1500™

6 inch pipe 949 CFM @ 1.8” W/C SP

5 inch pipe 739 CFM @ 3.5” W/C SP

4 inch pipe 572 CFM @ 5.3” W/C SP

3 inch pipe 467 CFM @ 6.1” W/C SP

0 CFM @ 7.9” W/C SP

(1.5hp)

83.7”

(2hp)

84.6”

(3hp)

84.6”

(5hp)

87.9”

Performance: V-3000™

6 inch pipe 1105 CFM @ 3.3” W/C SP

5 inch pipe 955 CFM @ 5.3” W/C SP

4 inch pipe 790 CFM @ 7.2” W/C SP

3 inch pipe 587 CFM @ 9.0” W/C SP

0 CFM @ 11.75” W/C SP

Performance: V-5000™

8 inch pipe 1498 CFM @ 1.65” W/C SP

7 inch pipe 1326 CFM @ 2.95” W/C SP

6 inch pipe 1210 CFM @ 4.05” W/C SP

5 inch pipe 988 CFM @ 6.9” W/C SP

0 CFM @ 13.6” W/C SP

Dimensions shown w/ 2” ex hose between drum and cone collars.

Allow 1 - 2” from ceiling for motor venting.

50”

25”

34”

30”

System

Performance

System

Dimensions

Options

Integral

Fan Blower

Filter Media

Included

Sound

Level

Dust Bin

U.S. Made Baldor or Leeson

1.5, 2, 3 or 5 Horsepower Single Phase

TEFC Motor, (2hp) 1.15 SF (3 / 5hp) 1.0 SF / Insulation

Class F for extra protection and motor life

Voltage: 115 (1.5) 230 (2 / 3 & 5hp)

Amperage: 8 (1.5) 11.5 (2hp) / 13 (3hp) / 19.5 (5hp)

(3) Tripod Aluminum Legs if stand is included.

Filter w/ Internal Silencer

FREE D.I.Y. Duct Design Guide

Flame Guard Arrestor - Pat. # 8,496,719

Pre-Wired Magnetic Starter -

Filter Grounding Wire

With Standard Silencer & Filter: 73 - 81 dBA @ 10’

Our Quietest System.

35 Gallon Fiber Drum - ODK350701 Standard

55 Gallon Fiber Drum - ODK550701 - Additional Charge

Fan Wheel - Backward Inclined / Non-Sparking, Non-

Ferrous as Required by NFPA Fire Code / Dynamic,

Two-Plane Balanced to ISO 6.3 Specications. The Same

as Aircraft Turbine Rotors.

Industrial

Quality

Motor

*Oneida reserves the right to change or modify specs and system appearance without notice.

Actual system appearance may vary.

w/ On-Off Switch Preset for Add-On Remote

with Amperage Overload Protector (1 Phase)

See Accessories

page for pricing.

Remote Control - Radio Frequency

Bag Gripper

Shop Plan Design Service

Wall Mount

Approx. 949 CFM @ 1.8” S.P. (1.5hp)

Approx. 1080 CFM @ 2.5” S.P. (2hp)

Approx. 1105 CFM @ 3.3” S.P. (3hp)

Approx. 1498 CFM @ 1.65” S.P. (5hp)

13”x 36” 95 Sq. Ft. GE Certied (H-12) HEPA Media.

MERV 16+ rated.

See specs on website.

See Specications Below

Line of Sight Not Required.

35 Gal.

61.75”

55 Gal.

73.75”

Ht. w/ 35 Gallon Drum: (1.5hp) 83.7” - (2hp) 84.6” - (3hp) 84.6” - (5hp) 87.9”

Footprint w/ Ext. Cartridge: 30”x 50”

Inlet Diameter: 6”, 8” (5hp)

Powder Coated Paint Finish Over Steel

U.S. Pat. #

8,377,160

V - Systems Owner’s Manual O.A.S. 2010

IV. Stand Assembly

Stand Kit Contents

Hardware Kit (1) - AHX002107

Rubber Leg Cap (3) - RCR012500

Rubber Leg Cap

Stand Leg

Stand

Brace

Mid-

Gusset

Top

Gusset

Mounting

Ring

Cone

Top Gusset (3) - RFG010000

Mid-Gusset (3) - RFG010003

Stand Leg Set 35 Gal. (3) - OSK354800

Stand Leg Set 55 Gal. (3) - OSK556200

1. Place rubber leg caps on long end of leg.

2. Attach top gusset and mid-gusset to legs using 2” carriage

bolts then a washer and Nylock nut.

3. Attach the braces to the mid-gussets using the 3/4” car-

riage bolts and a washer and Nylock nut.

4. Attach cyclone cone to top gussets using the mounting ring

by 5/16”x 1” bolts using the sequence of bolt, washer, cone/

stand, washer, Whiz nut.

Stand Braces

Note: Stand legs will angle slightly inward when connected to

cyclone. This adds stability to the unit and makes a slightly larger

footprint than if the legs were perfectly vertical.

V - Systems Owner’s Manual © O.A.S. 2010

1. Push clips onto inside circle on Fan Housing, making sure clip is pushed all of the way on, that the bolt

holes are in alignment with the clip holes and that the small barrel on the clip is on the INSIDE of the Fan

Housing as shown in diagram.

2. Stick the gasket material around the Fan Housing as shown in the diagrams, outside of the bolt circle.

Making sure of a complete seal. Dust collection systems cannot operate effectively without being tightly

sealed with no air leaks.

Bolt

Washer

Motor Plate

Clip

Gasket

Material

Fan

Housing

that this part ofIt is CRITICAL

the clip is put on the inside of

the Fan Blower Housing as

shown here. Otherwise you

will not get the seal needed

for complete dust collection

Proportions and sizes of parts may be

exaggerated for purposes of explanation.

Instructions for Attaching Motor Plate to Fan Housing.

V. Cyclone Assembly Instructions

3. Attach Motor and Motor Plate to Fan Housing.

Gasket material goes

outside of clip holes on

top of fan housing.

V - Systems Owner’s Manual © O.A.S. 2010

2. Put included self-sticking gasket on top rim of cone.

Make sure there is NO gap where both ends of gasket

meet. This is VERY important for an air tight seal.

1. Assemble stand per Pg. 5. If using wall bracket, mount to

wall per Pg. 16.

3. Put cone on stand and attach with

provided 5/16” bolts in System Hard-

ware Kit as shown on page 4. Line

up the two corresponding holes in

the ring to the gussets. (Slots are for

mounting with a wall bracket.)

4. Attach U-Spring clips as

shown on Pg. 6 to top of Fan

Housing. Then apply gas-

ket as shown, making sure

the outlet is to your left as

you look down as shown in

diagram.

5. Carefully lift housing on top of cone keeping gasket

side up. (This is best done using two people.) Carefully

line up the holes in housing with the holes in the cone top,

keeping in mind the direction you want your outlet to face.

Then attach using provided 5/16” ange bolts and 5/16”

washers. Do not use over 17 ft. lbs. of torque. You will

need a sturdy step ladder for this.

6. Carefully lift motor assembly on top of housing. It is

very heavy and a two person job. Watch your ngers

when you lower the motor to the housing!

Parts of this procedure require at least two people

to complete. Use extreme caution and good sense

when assembling this unit. Parts of it are very heavy.

V. Cyclone Assembly Instructions

V - Systems Owner’s Manual © O.A.S. 2010

7. Line up the holes in housing with the holes in the motor

plate. Then attach using provided 5/16” ange bolts and

5/16” washers. You will need a sturdy step ladder for this.

8.Place gasket material around lter plate as shown in dia-

grams. You may have to partially cover the bolt holes. Just

make sure that there is enough room for the bolts to push

through. and that there is no gap where the ends meet.

10. Attach gasket to

housing outlet, making

sure there is no gap

where ends meet. You

may have to trim out

some gasket to ensure

that the bolt holes are

clear.

11 The (7) 3/8” hex head

bolts and whiz nuts to

attach the plenum are in

the kit hardware.

4 hole side is near dust collector.

Gasket

Filter

Mounting

Plate

Gasket

Plenum

Support

Hanger

J Hook

Gasket

Outlet

9. Attach Plenum to Plate:

Push Carriage bolts through

bottom of lter plate making

sure gasket side is up and

rectangular shaft is in hole.

Tighten with 5/16” whiz nut

and washer as shown in dia-

gram. Make sure plate is at-

tached to the support hanger

end of plenum as shown in

diagram to the right.

Filter

Plate Washer

Nut

Bolt

Plenum

V - Systems Owner’s Manual © O.A.S. 2010

18. Plug in Magnetic Starter and you are ready to connect

your collector to your ductwork and go!

16. Distance between the drum lid and cone can vary.

Some systems have little space there to minimize overall

system height.

In some cases, the exible hose will have to be cut down

(especially with stands).

OAS ships 1’ of hose as standard but this is not necessarily

the needed length once the system is installed.

Tools Needed: Razor Knife / Diagonal Cutters

Measure length between drum lid and collar of cone.

Measure hose while it is extended (don’t overly compress

the hose). This allows the lid to move up when installed.

Cut the hose with razor knife and then cut the wire with

diagonal cutters. Don’t cut too short! If in doubt, cut a

little long. Trim if necessary.

12. Pull Silencer out straight

and place in top of lter,

pushing it down into lter until

top ring is ush with lter and

ts snugly within the gasket.

13, Put 4 J-hooks into lter plate as shown above and

loosely tighten with thumb nuts.

14. Hook J-hooks under metal rim of lter and evenly

tighten, making sure lter’s gasket is tightly sealed against

lter plate.

15. Put J-hooks through Dust Bin as shown and tighten

with Thumb Nuts, making sure you have an even seal

between the lter gasket and Dust Bin.

17. Connect short end of Filter Grounding Wire from motor

to plenum bolt as shown below and clamp alligator clip to

lter mesh.

Filter

J-Hook

Dust Bin

Thumb Nut

Ring Terminal

End

Filter

Plate

Filter

Washer

Nut

Bolt

Plenum

Collector

Hose Clamp

Flex Hose

Dust Bin

Drum Grounding Wire

To attach the Drum

Grounding Wire, start a

small hole in bottom of

cone above ex hose

and in the top of the

dust drum, then attach

the wire with the 3/8”

included self-tapping

screws.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 8491685 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XGK030035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 2000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD002030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop DC Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 10 HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2005c3HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Gorilla XXP999901 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung