Structural Concepts Addenda CSF3931 Montageanleitung

Rev B Date: 8.27.2007

PN 99696

INSTALLATION &

OPERATING MANUAL

READ AND SAVE THESE INSTRUCTIONS

Models: CSF3931 39”L x 73 1/4”H* x 31”D

CSF4231 42”L x 73 1/4”H* x 31”D**

* Includes Top Sign

** Without Package Ledge. 36 1/2”D With Package Ledge.

Model Shown With

Optional Upper Signage

I:\Oper Manuals\Addenda\CSF[L]31_99696.pub

SELF-SERVICE FLOOR MODEL UNITS

888 E. Porter Road · Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts

TABLE OF CONTENTS

OVERVIEW AND WARNINGS ……………………..…………………..…….………….....…..………

INSTALLATION ………….…………………………………………………………………………………

START-UP AND OPERATION ……….. …..….…………………...………...…..………………………

MAINTENANCE FUNDAMENTALS ………………………….………………………………... .. …... .

SERIAL LABEL & LOCATION / INFORMATION LISTED / ADD’L TECH INFO & SERVICE ..……

TROUBLESHOOTING ……………….……………………………………………….………….………..

ILLUSTRATED PARTS BREAKDOWN …………………………………………………….…...………

PARTS LIST ……………..…………………………………………………………………………………

CLEANING SCHEDULE..…………………………………………………...………………….…………

WARRANTY…………...……………………………………………………..……………………..………

TECHNICAL SERVICE……..……………………………………………………………….….....………

OVERVIEW AND WARNINGS

OVERVIEW

• This merchandiser is designed for the display of non-hazardous, unpackaged bakery

products.

• These cases should be installed and operated according to the following instructions to

insure proper performance.

• This unit is designed for the display of products in ambient store conditions where

temperatures and humidity are maintained at a maximum of 75° F and 55% relative

humidity.

WARNING

Risk of Electric Shock.

Disconnect Power Before Servicing Unit

WARNING

ELECTRICAL

HAZARD

CAUTION

Lamps have been treated to resist breakage and must be replaced with a

similarly treated lamp.

CAUTION

INSTALLATION

Remove Unit From Skid

• Position the unit near a suitable electrical outlet.

• Caution: case must always remain supported or

center of gravity imbalance will cause case to fall.

• Slide unit to rear of skid and tip backward off skid.

Position and Level Units

For your safety, equipment is furnished with a

properly grounded cord connector. Do not at-

tempt to defeat the grounded connector.

Lift unit with suitable prying bar and blocking. Note

the point of lifting to minimize damage to case. Ro-

tate leveler to obtain proper height to stabilize and

level the unit.

Level Units with

7/16 Wrench

START-UP AND OPERATION

For your safety, equipment is fur-

nished with a properly grounded

cord connector. Do not attempt to

defeat the grounded connector.

Merchandiser Start-Up

• Do not use an extension cord with

this appliance.

• Do not operate this equipment with

a damaged cord, plug or outlet.

• Insure the power switch is off.

• Plug cord into a certified 120V elec-

trical outlet with ground.

• Turn lights on.

• On floor models without a stor-

age door the switch is located at

the front base of the unit under

the front panel on the left hand

side.

• On floor models with a storage

door, the switch is located inside

the base storage area on the left

hand side.

• Lights should come on at the same

time. First time lighting may require

a short warm up period for the

bulbs. Slightly dim or a flickering of

new bulbs is normal.

Tissue Dispenser

• Remove tissue dispenser.

• Place a tissue box into the dis-

penser as shown.

Internal

Light Switch

Storage Door

When Provided

Tissue Dispensers vary

depending upon model

MAINTENANCE FUNDAMENTALS

Shelf Assembly Removal

• Shelves can be removed for repositioning,

removal (for individual merchandising re-

quirements) and cleaning.

• Slide the front shelf support back rotate up

and lift straight up to separate from brackets.

• Slide the rear shelf support back rotate up

and lift straight up to separate from brackets.

• Remove brackets. Note it may be necessary

to remove the nylon shipping bracket re-

tainer. Pliers will be required to accomplish

this task.

Removing of Decking

• Remove lower shelf assembly.

• Remove interior deck by pushing up from

underneath in the bag storage area.

Door “Hold Open” Feature

To reposition the shelving or restock the

shelves, it is first helpful to use the door ‘hold

open” feature.

• Open the door all the way (See light fixture).

• Caution damage will result if pin is not

lowered before attempting to close the

doors.

• Inside the unit, at the top of each door

hinge, is the pin slide cover.

• Slide the pin cover up until the pin extends

approximately 1/2 inch above the door hinge.

• Release the door assembly allowing the pin

to rest on the outer door frame.

• To close, fully open the door and retract the

pin into the hinge and allow the door to

close.

Front Shelf Support

Rear

Shelf

Support

Shelf Bracket

Bracket

Retainer

Bracket

Retainer

Extension

MAINTENANCE FUNDAMENTALS

Light Fixtures

Light fixtures are located on the sides of

each door assembly, both sides (just in-

side doors).

• Open the door all the way.

• Access lamp by removing the lamp

cover/diffuser.

• Apply gentle squeezing pressure to

lamp cover; rotate to release

cover.

Removal of lamp:

• Press bulb down until top contacts are

clear of the upper socket.

• Tilt top of bulb away from the upper

socket and lift bulb out.

• Replace bulb by performing this opera-

tion in reverse order.

• See light assembly illustration below

right.

Light Ballast Access and Field Access

Box Access

• Disconnect electrical power from case.

• Flip Down the Front Panel / Storage

Door (see front case illustration at right

and rear case illustration below).

Bulb

Lamp Cover

Lower Socket

with Spring

Light Assembly

Ballast

Box

Front Panel /

Storage Door

Field

Access

Box

Field

Access

Box

Ballast

Box

SERIAL LABEL & LOCATION / INFORMATION LISTED / ADD’L TECH INFO & SERVICE

Serial Label, Location, Information Listed, Add’l Technical Info & Service

• Serial labels are located near the electrical access on your case.

• Serial labels contain electrical, temperature & refrigeration information, as well as regulatory

standards to which the case conforms.

• For additional technical information and service, see the TECHNICAL SERVICE page in this

manual for instructions on contacting Structural Concepts’ Technical Service Department.

• See images below for samples of both refrigerated and non-refrigerated serial labels.

----- Sample Serial Label For Refrigerated Case -----

----- Sample Serial Label For Non-Refrigerated Case -----

888 E. Porter Road · Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts

SAMPLE ONLY

SAMPLEONLY

SAMPLE ONLY

TROUBLESHOOTING

Case Lights Not Working Check bulbs for proper installation and connection.

Check for burned out bulbs.

System is not Operating Confirm the utility power is on.

Check the circuit breaker box for tripped circuits.

ILLUSTRATED PARTS BREAKDOWN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Structural Concepts Gewerbliche Lebensmittelgeräte Handbücher

Structural Concepts

Structural Concepts Oasis BV4732 Bedienungsanleitung

Structural Concepts

Structural Concepts IMPULSE CGC2830 Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse 62486 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis MI44RF Montageanleitung

Structural Concepts

Structural Concepts Oasis B824TM Bedienungsanleitung

Structural Concepts

Structural Concepts HVP48SS Montageanleitung

Structural Concepts

Structural Concepts REVEAL NR3633RSV Bedienungsanleitung

Structural Concepts

Structural Concepts GHSS476HRD.5718 Bedienungsanleitung

Structural Concepts

Structural Concepts K Series Montageanleitung

Structural Concepts

Structural Concepts ADDENDA 86772 Bedienungsanleitung

Structural Concepts

Structural Concepts GMDSES8R Bedienungsanleitung

Structural Concepts

Structural Concepts Addenda 20-53882 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B32 Bedienungsanleitung

Structural Concepts

Structural Concepts Reveal NR3613DSV Bedienungsanleitung

Structural Concepts

Structural Concepts HARMONY HMO2653R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis COU2757R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BD3632 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B4732 Montageanleitung

Structural Concepts

Structural Concepts grocerant FB9S-6HO.7355 Montageanleitung

Structural Concepts

Structural Concepts Oasis B3924RH Bedienungsanleitung

Structural Concepts

Structural Concepts FUSION Bedienungsanleitung

Structural Concepts

Structural Concepts SB5735 Series Montageanleitung

Structural Concepts

Structural Concepts grocerant DP8HP60WD.5718B Montageanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch