Structural Concepts G Series Bedienungsanleitung

Operating Manuals\G-Series\G-Series_Heated_Self-Service Unit_20-95651.pub Rev B Date: 10.4.2019

888 E. Porter Road ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 www.structuralconcepts.com

G-SERIES SELF-SERVICE MERCHANDISER WITH HEATED SHELVES AND DECK

> SCC PROPRIETARY THERMOSTATS AT CASE REAR

> REMOVABLE WIRE RACKS ON HEATED SHELVES

> REAR SLIDING DOORS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION AND

OPERATING MANUAL

-SERIES 20-

95651

Important! See Installation

Section Of Manual To

Confirm Proper Placement of

“Caution-Hot” Labels on Heat-

ed Shelves

Model GHSS476HRD.5718

TABLE OF CONTENTS

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS .............…..

INSTALLATION: SKID REMOVAL / POSITIONING CASE / FRAME SUPPORT RAIL SHIMMING ….

INSTALLATION, CONT’D: ATTACHING SPLASH GUARD BRACKET TO REAR FRAME

SUPPORT RAIL ………………………………………………………………………….………………

INSTALLATION, CONT’D: IMPORTANT! HEATED SHELF LABEL PLACEMENT …………...……….

INSTALLATION, CONT’D: REMOVABLE FRONT & REAR TOE-KICKS ….…………………………….

STARTUP: MAIN POWER SWITCH / LIGHTS SWITCH / THERMOSTATS ………………….………….

STARTUP, CONT’D: OPERATION AND SHUTDOWN (AUTHORIZED PERSONNEL ONLY!) ............

GENERAL LAYOUT: CASE FRONT …………………………………………………………………………….

GENERAL LAYOUT, CONT’D: CASE REAR ...………………………………………………………………...

GENERAL LAYOUT, CONT’D: LED LIGHT SWITCH AND FIXTURES / LED REMOVAL &

REPLACEMENT …………………………………………………………………………………………..

CLEANING SCHEDULE: CASE EXTERIOR - DAILY, WEEKLY AND MONTHLY …...………………...

CLEANING SCHEDULE, CONT’D: CASE INTERIOR - DAILY ………………………….………………...

SERIAL LABEL & LOCATION / TECHNICAL INFORMATION / ADDITIONAL INFORMATION ……...

TROUBLESHOOTING ….…………………………………………………..………………...…………..……..

SCC TECHNICAL SERVICE CONTACT INFORMATION & WARRANTY INFORMATION ..…….….....

3-4

OVERVIEW

This merchandiser is designed for dry heating operations

throughout the product area. Heat is generated from both

shelving and deck.

x Cases should be installed and operated according to

this operating manual’s instructions to insure proper

performance.

x These Structural Concepts® self-service heated

merchandisers are designed to hold pre-heated hot

foods at 140 °F to 165 °F (60 °C to 74 °C).

x Product must be pre-heated to these temperatures

PRIOR TO being places in merchandiser. This case is

NOT designed to heat product from cold or ambient

conditions.

x This merchandiser is designed for display of

perishable, packaged products.

x Improper use will void warranty.

TYPE “1” CONDITION

This unit is designed for the display of products in ambient

store conditions where temperatures and humidity are

maintained within a specific range.

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical and plumbing codes.

WARNING

Risk of electric shock. Disconnect power before servicing unit.

CAUTION! More than one source of electrical supply is

employed with units that have separate circuits.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

ELECTRICAL

HAZARD

WARNING

Shelves and Decks Are Hot! Disconnect and allow to cool

45 minutes before cleaning or removing from case.

WARNING

HOT

SURFACE

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS - PAGE 1 of 2

x Ambient conditions are to be at 55% max. humidity

and maximum temperatures of 75 °F (24 °C).

INTEGRATED AVERAGE PRODUCT TEMPERATURE

x These units are designed to merchandise product at

an integrated average product temperature of

150 °Fahrenheit / 66 °Celsius.

THERMOMETERS

x Thermometers in equipment reflect internal air

temperature only (not actual food temperature).

x Use probe thermometers to determine actual product

temperatures.

COMPLIANCE

x Performance issues when in violation of applicable

NEC, federal, state and local electrical and plumbing

codes are not covered by warranty.

x See below compliance guideline.

WARNINGS

x This page contains important warnings to prevent

injury or death. Please read carefully!

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

PRECAUTIONS

x Following are important precautions to prevent damage to unit, merchandise or product.

x Please read carefully!

CAUTION! LAMP REPLACEMENT GUIDELINES

LED lamp replacements must meet factory specifications.

CAUTION

CAUTION! ADVERSE CONDITIONS / SPACING ISSUES

x Performance issues caused by adverse conditions are NOT covered

by warranty.

x End panels must be tightly joined or kept at least 6-inches away from

any structure to prevent condensation.

x Unit must be kept at least 15-feet from exterior doors, overhead HVAC

vents or any air curtain disruption to maintain proper temperatures.

x Do not expose to direct sunlight or heat source (ovens, fryers, etc.).

x

Keep at least 8-inch clearance above unit for air discharge

(self-contained units only).

CAUTION

CAUTION! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING / PLUGS - PAGE 2 of 2

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

WIRING DIAGRAM FORMAT & LOCATION

x Each case has its own wiring diagram folded & in its own packet.

x Wiring diagram placement may vary; it may be placed near ballast

box, field wiring box, raceway cover, or other related location.

SEAL FLOOR-MOUNTED UNITS TO THE FLOOR

x

Thoroughly clean floor to assure a secure seal!

x

Base frames or fixed (non-removable) cladding,

panels and/or splash guard brackets must be

sealed to floor with silicone that meets or

exceeds food grade NSF/ANSI Standard 51.

INSTALLATION: PALLET REMOVAL / POSITIONING CASE / FRAME SUPPORT RAIL SHIMMING

2. Position & Align Case Alongside Other Cases

x Before shimming frame support rails, make

certain that the case is in proper position and if

required, aligned with adjoining case.

x This may require the repositioning of the case

you are installing or the already positioned

case.

3. Shim Frame Support Rails

x Most cases have frame support rails.

x Shims will be provided with all cases that have

frame support rails.

x Use shims to level case.

x You may need to remove front and/or rear

toe-kick to access frame support rails

x Note: After case is in position, it must be

sealed to floor to prevent entry or leakage

of liquid or moisture.

x See illustration at right.

Frame Support Rails

1. Remove Unit From Pallet

x Caution: Case must always remain

supported or center of gravity will allow

case to fall.

x Slide unit to rear of pallet and lean

backward off skid.

x Slide pallet out from under case while

case is being supported.

x See illustration at right.

Pallet

INSTALLATION, CONT’D: ATTACHING SPLASH GUARD BRACKET TO REAR FRAME SUPPORT RAIL

4. Attaching and Sealing Splash Guard Bracket

To Frame Support Rail at Case Rear

x The separately shipped splash guard bracket is

designed to prevent entry or leakage of liquid or

moisture to underside of case.

x After case has been properly positioned and frame

support rails have been shimmed, place a bead of

silicone sealant to underside of splash guard

Frame Support Rail

Silicone Sealant

bracket (that rests on floor). Center back of

bracket flush against frame support rail.

x Then, attach to frame support rail with

SCC-supplied screws.

x After splash guard bracket has been secured to

frame support rail, apply another bead of silicone

sealant where front of bracket meets floor.

x Attach rear toe-kick to case (with 2 screws).

Splash Guard

Bracket (Shown

Attached)

Removable Toe-Kick

Splash Guard

Bracket

Frame Support

Rails

--- View With Splash Guard Bracket Attached ---

--- View With Splash Guard Bracket Removed ---

INSTALLATION, CONT’D: IMPORTANT! HEATED SHELF LABEL PLACEMENT

Important! Check

That “Danger-Hot”

Labels Are Placed

On Heated Shelves

As Shown.

5. Important! Check That “Danger-Hot” Labels Are Properly Attached To Case.

x Shelves can get extremely hot and cause severe burns.

x Illustration below shows proper placement of “Danger-Hot” labels.

x Two labels must be placed on each shelf and lower panel (as shown below).

x If labels are NOT properly attached, contact Structural Concepts. See SCC TECHNICAL SERVICE

CONTACT INFORMATION section in this manual for contact information.

INSTALLATION, CONT’D: REMOVABLE FRONT & REAR TOE-KICKS

6. Removable Front Toe-Kick (Magnetized)

x Front toe-kick is usually shipped separately.

x Front toe-kick is removable by grasping

toe-kick’s upper lip and pulling toward you (to

release from magnets).

x See illustration below.

--- Toe-Kick Removable From Case Rear ---

Front

Toe-Kick

--- Toe-Kick Removable From Case Front ---

Rear

Toe-Kick

Magnet

Magnet 6

7. Removable Rear Toe-Kick (Screw-Retained)

x Rear toe-kick is usually attached at case

shipment.

x Rear toe-kick is removable by removing two (2)

screws and lifting away from case.

x See illustration below.

STARTUP: MAIN POWER SWITCH / LIGHTS SWITCH / THERMOSTATS

1. Main Power Switch

x Main power switch is at case rear.

x Main power switch controls power to lights AND

thermostats.

x See illustration below.

2. Lights Switch

x When light switch is turned on, all lights in entire

case will turn on.

x See illustration below.

3. Thermostats

x Thermostats are at case rear

x Thermostats control heat to deck and all three

(3) shelves.

x Left thermostat controls heat to deck and

bottom shelf.

x Right thermostat controls heat to middle shelf

and top shelf.

x See next page for thermostat control specifics.

--- Case Rear ---

5 5 5 5

STARTUP, CONTINUED: OPERATION AND SHUTDOWN (AUTHORIZED PERSONNEL ONLY!)

4. Merchandiser Daily Start-Up

x Turn main power switch and lights switch on.

x LED lights should all come on at once.

x Temperature controls are pre-set at factory to

recommended settings.

x Press pre-heat buttons. Pre-heat lights will

illuminate. Case will warm for 20 minutes.

x After pre-heat lights are off, product may be

placed on racks.

x Caution! Deck and shelving is hot! Do not touch

unless dials have been turned off and surfaces

are cool!

x Heat settings have a maximum setting of “9” and

a minimum setting of “1”. A setting of “0” turns

heat OFF.

x Allow 20 minutes at NEW settings to determine if

product temperatures are acceptable.

x Note: Default factory setting are at “5”.

x Adjust controller until desired product

temperatures are reached.

x Caution! Food MUST BE cooked PRIOR to being

placed in the case. Food should be heated to a

temperature of between 150 °F to 160 °F (65.6 °C

- 71 °C) prior to placing in case. Food temperature

must NOT be allowed to be below FDA guideline

of 140 °F (60 °C).

x Use probe to check food temperature before

placing in the case.

x After product is placed in case, check product

temperature (again) after one hour to verify that

proper food temperatures are maintained.

x Should product temperatures be outside of range,

adjust temperature controls for that particular area

(shelf, deck or overhead) up or down by one

number.

x Check food temperature again after one hour.

5. Temperature Control Settings

x Temperatures of all food products are to be at

140 °F to 165 °F (60 °C to 74 °C), for decks and

shelves (including optional shelf #4).

6. Operating Tips

x When restocking, place new product at rear and

rotate older product to front of case.

x Display product expected to sell within 4 hrs.

x Clean up residue immediately. Case will cause

spills and debris to harden to surface!

7. Shutting Down Case

x Remove all product from the case.

x Turn Main Power Switch “OFF”.

x Allow case to cool for 45 minutes before cleaning.

x See CLEANING SCHEDULE (DAILY /

WEEKLY) - CASE INTERIOR for specifics.

--- Top Shelf ---

--- Mid Shelf ---

--- Bottom Shelf ---

--- Deck ---

--- Case Rear ---

--- Case Front ---

5 5

Andere Handbücher für G Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Structural Concepts Gewerbliche Lebensmittelgeräte Handbücher

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Addenda CSF3931 Montageanleitung

Structural Concepts

Structural Concepts ADDENDA 86772 Bedienungsanleitung

Structural Concepts

Structural Concepts grocerant FB9S-6HO.7355 Montageanleitung

Structural Concepts

Structural Concepts GMDSES8R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV4732 Bedienungsanleitung

Structural Concepts

Structural Concepts GHSS1252RLB.6796F Bedienungsanleitung

Structural Concepts

Structural Concepts grocerant DP8HP60WD.5718B Montageanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts HARMONY HMO2653R Bedienungsanleitung

Structural Concepts

Structural Concepts K Series Montageanleitung

Structural Concepts

Structural Concepts Impulse Series Bedienungsanleitung

Structural Concepts

Structural Concepts FSE663R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV3632 Bedienungsanleitung

Structural Concepts

Structural Concepts REVEAL NR3633RSV Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis MI44RF Montageanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts GHSS476HRD.5718 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse CSC3223 Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B3924RH Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse 62486 Bedienungsanleitung

Structural Concepts

Structural Concepts Addenda 20-53882 Bedienungsanleitung

Structural Concepts

Structural Concepts IMPULSE CGC2830 Bedienungsanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch