Tennsco 1872 Bedienungsanleitung

PK-1830918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Deluxe Combination Cabinet

Unassembled Models 1872 & 2472

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

36w x 18d

36w x 24d

18w x 18d

18w x 24d

200 lbs.

75 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF 1872 OR 2472 CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.

2. Place the cabinet back (Ref. No. 1) on a protected surface

to prevent scratching the paint. The ange on the bottom of

the back should be

facing upward.

1. The reference numbers used throughout this sheet refer to

the illustration on the back cover. This is to help you to

identify the various parts as they are mentioned.

Attach the left side (Ref. No. 2) to the back by placing ange

(A) around the back and bolting together with seven bolts

and nuts (Ref. Nos. 19 & 20). Be sure that the lances on all

shelf adjustment strips (B) point in the same direction.

5. Place the top (Ref. No. 5) onto

the unit. Be sure that the

anges tuck inside the cabinet

sides and back. Secure with

eleven nuts and bolts. The

front part of the top

will bolt into place

in step 8.

3. Attach the right side (Ref. No. 3) to the back in the same

manner as in step 3, again making sure that the ange

is around the back and that the lances on the shelf adjust

ment strips are pointed in the same direction as those on the

back and left side.

6. With both doors in the closed position, lift the door and

frame assembly (Ref. No. 6) and place it over the cabinet

body. Be aware that the door latches have not yet been

7. With the door and frame assembly in place, attach it

securely to the unit by opening each

door, one at a time, and securing

the frame assembly using

two bolts and twenty

nuts. This will require

attaching nuts to the

nine pre-welded studs

along each side, plus

two bolts and nuts

along the top.

⁭

attached so the

doors could

potentially swing

open if the door

frame is held in

an upsidedown

position. The door

frame should

cover the outside

edges of the

entire storage

cabinet front.

⁭

4. Place the shelf (Ref. No. 4) into one

of the upper positions on the unit

by inserting the shelf edges into

the lances on all four shelf

adjustment strips. Be

sure that the

channeled

edge of the

shelf is

toward the

cabinet front.

⁭

Two holes

must be in front.

8. Place the the bottom (Ref. No. 7) in the lowest notch of the

shelf adjusting strips on the back. Make sure the ange with

two holes faces the front, and that it is over the ange of the

frame sill. If necessary, you may

push out on the side

walls to

enable

the bottom

to more

easily slide

into position. Attach

the shelf securely by bolting

the bottom to the frame sill

with two bolts and nuts.

Insert shelf

into bottom lances.

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 10, unless

otherwise speciﬁed.

All lances point UP on

the back and side.

Flanges

face upward

⁭

Flange goes

under back.

⁭

Using two people, set the unit upright and tighten all nuts

10.

around the entire unit.

Attach the coat rod bracket

(Ref. No. 10) to the

underside of the shelf,

inserting one bolt and nut

through the hole provided

on the far right and far left

side. The open side of the

side brackets should face

into the unit. Insert the coat

rod (Ref. No. 11) into rst

one bracket, and then into

the other by exing the

second bracket.

⁭

Levelers

Access Holes

12. The cabinet must be level

in order for the doors to

close properly. Leveler

may be adjusted by placing

the nut driver through the

hole in each end of the

sill and adjusting the

leveling screw.

9. Insert the partition (Ref. No. 8) into the cabinet, aligning the

four holes in the partition with the two holes in the cabinet

bottom and the two holes in the cabinet shelf. Attach with

four bolts and nuts, making sure that the bolts are inserted

from the top downward to prevent items stored on the shelves

from being snagged.

11. Insert the four partition shelves (Ref. No. 9) at the desired

levels. The shelves should be inserted using the same method

shown in step 4.

⁭

⁭⁭⁭

1. Place the locking handle

(Ref. No. 13) on the right

hand door and fasten with

two #8-32 X 1/4hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 14) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

16) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 12) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

15) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

5. Attach the “dummy” handle

(Ref. No. 17) using two

#8-32 X 1/4hex-head bolts

and lock washers.

Handle/Locking System Installation

⁭

⁭⁭

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 18)

Coat Rod

(Ref No. 11)

Bottom

(Ref No. 7)

Coat Rod

Bracket

(Ref No. 10)

Dummy Handle

(Ref No. 17)

Left Side

(Ref No. 2)

Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 16)

Locking Bar Guide

Nylon Insert

(Ref No. 15)

Locking Bar Set

(Ref No. 12)

Locking Cam

(Ref No. 14)

Locking Handle

with Keys

(Ref No. 13)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panel 1 043BA 1 043BA

2 Left Side 1 043LS 1 044LS

3 Right Side 1 043RS 1 044RS

4 Shelf 1 301 1 302

5 Top 1 043TO 1 044TO

6 Door & Frame Assembly 1 043DA 1 043DF

7 Bottom 1 043BO 1 044BO

8 Partition 1 045PA 1 046PA

9 Partition Shelf 4 304 4 305

10 Coat Rod Bracket 2 045RB 2 045RB

11 Coat Rod 1 046CR 1 046CR

12 Locking Bar Set 1 043LB 1 043LB

13 Locking Handle w/keys & hardware 1 043LH 1 043LH

14 Locking Cam* 1 944LC 1 944LC

15 Locking Bar Guide Insert (Nylon)* 2 944GI 2 944GI

16 Cotter Pin* 1 CTRPN 1 CTRPN

17 Dummy Handle* 1 043DH 1 043DH

18 Tennsco Nut Driver 1 TOOL-2 1 TOOL-2

19 #8-32 x 3/8” bolts (not shown above) 35 ** 35 **

20 #8-32 nuts (not shown above) 53 ** 53 **

*Included in Ref. No. 13, locking handle with keys and hardware (Part No. 043LH). **Available Locally

QTY. PART NO.

⁭

Door & Frame

Assembly

(Ref No. 6)

NOTE: Additional hardware may be included for replacement purposes.

QTY. PART NO.

1872 (18”d Cabinet) 2472 (24”d Cabinet)

⁭

Partition

(Ref No. 8)

⁭

Partition Shelf

(Ref No. 9)

⁭

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

49B183

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco BK6-121812-1 Bedienungsanleitung

Tennsco

Tennsco SR-59 Bedienungsanleitung

Tennsco

Tennsco 1470RH Bedienungsanleitung

Tennsco

Tennsco B-6000 Bedienungsanleitung

Tennsco

Tennsco J2478C Bedienungsanleitung

Tennsco

Tennsco Capstone Shelving Units Bedienungsanleitung

Tennsco

Tennsco J1842A-N Bedienungsanleitung

Tennsco

Tennsco J2478A-N-W Bedienungsanleitung

Tennsco

Tennsco CC-30 Bedienungsanleitung

Tennsco

Tennsco LSS-361872 Bedienungsanleitung

Tennsco

Tennsco 1870RH Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco SINGLE TIER Bedienungsanleitung

Tennsco

Tennsco 1842 Bedienungsanleitung

Tennsco

Tennsco 4218 Bedienungsanleitung

Tennsco

Tennsco Sliding Door Jumbo Storage Cabinet JSD2478SU Bedienungsanleitung

Tennsco

Tennsco Jumbo Storage Cabinet J2478SU Bedienungsanleitung

Tennsco

Tennsco B-8400 Bedienungsanleitung

Tennsco

Tennsco Z-Line Steel Shelf Unit Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving Bedienungsanleitung

Tennsco

Tennsco 1420 Bedienungsanleitung

Tennsco

Tennsco zt7 Series Bedienungsanleitung

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco JUMBO Gebrauchsanweisung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung