CrimeStopper The Informer II CS-2016FM Bedienungsanleitung

CS-2016FM The Informer II™

2-Way FM Paging Alarm & Remote Engine Starting System

OPERATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of the Informer II™ by Crimestopper Security Products Inc. This booklet

contains the information necessary for operating your system. If any questions arise, contact your installation dealer or

Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Power,

Ground, LED, etc.

-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,

Dome light illumination, Door Locks, Trunk Pop, etc. These features may require additional parts and labor charges.

Consult with your installer about these features BEFORE installation!

CONTACT INFORMATION: This device complies with FCC Rules part 15. Operation is subject

to the following two conditions: 1) This device may not cause

interference, and (2) this device must accept any interference that

may be received, including interference that may cause undesired

operation. The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modification to this

equipment. Such modification could void the user's authority to

operate the equipment.

TECHNICAL SUPPORT (800)-998-6880

Monday - Friday 8:00am - 4:30pm Pacific

Website: www.crimestopper.com

E-mail: [email protected]

CRIMESTOPPER

SECURITY PRODUCTS, INC.

1770 S. TAPO STREET

SIMI VALLEY, CA. 93063 REV. B 09.2004

TABLE OF CONTENTS

Operation Cautions & Warnings……..…………..……………………………………………………………………2

Transceiver / Pager-Remote……….....…………..……………………………………………………………………3

CS-397TW Sidekick Remote Control…………………….…………………………………………………..…...…..4

Operating Instructions - Alarm……………………………………………………….………..……………..……..4-8

Remote Engine Control………………………...……………………………………………….…….………...….9-13

Anti-Carjack Protection...……………………………………….………….……..………………..………..………..14

LED Diagnostics………………..……………………………………………………………………….………..….…15

Transceiver / Remote Control Programming……………………………………………………..……………15-16

2 Vehicle Operation……...………………………….……………………………….………….…………….….……17

Troubleshooting / FAQ Section……………….…………………………………………………………..……..18-19

Low Battery Warning – LCD Remote / Setting Clock – LCD Remote……………………………….….…19-20

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident

resulting from the use of this equipment. This system is designed to be professionally installed into a car or

vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,

must be in perfect working condition.

DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to

repair and / or replacement charges.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this

system and its safety features. B) Check for proper operation of these safety features prior to accepting

delivery of the vehicle from the installation facility. C) Check and maintain the condition of the vehicle and all

items relative to the proper operation of this system and its safety features.

DO NOT remote start the vehicle in a closed garage. Make sure that the vehicle is outdoors, a garage door

is open, or there is adequate exhaust ventilation. Failure to observe this rule could result in injury or death

from poisonous Carbon Monoxide fumes. This is especially important when using the Timed Self-Start feature

of the unit 2

TRANSCEIVER / PAGER-REMOTE

PAGER / REMOTE TRANSCEIVER:

#1 ARM/

LOCK

#4 ENGINE

START/STOP

RECALL /

CAR I OR II

#3 TRUNK

POP

#2 DISARM/

UNLOCK

ANTENNA

START

FIXED

LCD

SCREEN

The hand-held remote transceiver is used to send and receive

information from the vehicle. The Control Module transmits High

Frequency FM signals from the vehicle to your over long

distances. Your range will vary depending on location, terrain,

and local RF noise/interference. This system is not guaranteed

to page you if you are behind concrete walls, underground, in a

large structure, or in an area with high levels of electronic

interference. Handle the pager/remote with care if the LCD

display and/or the electronics may be damaged if subjected to

abuse. The AAA Cell 1.5V alkaline battery can easily be

replaced by sliding open the battery access door on the back of

the remote. Battery life will vary depending on usage. The LCD

screen will display a low battery icon when the battery is low.

For more on range, see “Range Questions” on page 15.

ACTIVE 2-ZONE LCD DISPLAY:

The unique LCD screen includes both a Dot Matrix animated display and a vehicle icon. It is designed to show you

both Icon-based information and animated messages in real time as it is happening. When the alarm is disarmed or

armed with no activity to report, then dot matrix portion of the screen will remain BLANK.

BUTTON 1(Lock Symbol): BUTTON 5 (On side of remote):

•Press and Release to Recall the

last message from the LCD screen

•Press and Hold for 3 seconds to

change from Car 1 to Car 2 (Only

for use with 2-car operation).

•Press 5 times to Disable/Enable

audible beep tones from the

remote. (Remote will vibrate twice

to confirm silent mode)

•Press and release to Arm/Lock system.

•Press and Hold for more than 3 seconds to activate “Panic” feature.

BUTTON 2 (Unlock Symbol):

•Press and release to Disarm/Unlock system, or reset a cycle.

BUTTON 3 (Trunk Symbol):

•Press and Release to activate trunk pop (Auxiliary output #1) Optional

Feature.

•Press and Hold to activate a second optional feature (Auxiliary output

#2).

BUTTON 4 (Key):

•Press and release to Start/Stop engine. 3

CS-397TW SIDEKICK REMOTE

The CS-397TW 1-Way sidekick remote

adds flexibility to your CS-2016FM. You

can have the convenience of operating your

system without needing to carry the larger

pager remote. The Sidekick remote has

less range and offers all of the same

operation features except for page-back

confirmation. See diagram below for

Sidekick 1-Way remote operation.

CrimeStopper

LOCK/

TRUNK

REMOTE

UNLOCK/

VEHICLE 2

FLASHLIGHT

START

ARM

DISARM

BUTTON 1(Lock Symbol):

•Press and release to Arm/Lock system.

•Press and Hold for more than 3 seconds

to activate “Panic” feature.

BUTTON 2 (Unlock Symbol):

•Press and release to Disarm/Unlock system, or reset a cycle.

BUTTON 3 (Trunk Symbol):

•Press and Release to activate trunk pop (Auxiliary output #1) Optional Feature.

•Press and Hold to activate a second optional feature (Auxiliary output #2).

BUTTON 4 (Key):

•Press and release to Start/Stop engine.

BUTTON 5 (Upper side button of remote):

•Press for convenient flashlight function. The high-power LED acts as a mini flashlight.

BUTTON 6 (Lower side button of remote):

•Press and release to activate Vehicle #2 mode. (Led witl flash for 4 second to use vehicle #2, otherwise

remote will revert back to Vehicle #2 4

OPERATING INSTRUCTIONS - ALARM

Active Arming / Locking:

ARM/LOCK

Press button #1 (Lock symbol) on the transceiver. The System will arm emit one siren

chirp, one light flash, and the LED will begin to flash. Power locks will lock (if

equipped). Starter disable circuit will turn on. LCD Pager will beep once while

displaying a Down Arrow and a Lock symbol followed by the CSP logo. After a short

delay to allow the vehicle and electronics to settle, the system will be completely armed.

Disarming: / Unlocking

DISARM/UNLOCK

Press button #2 (Unlock symbol) on the transceiver. System will disarm and confirm

with two siren chirps, two light flashes, and the LED will turn off. Power locks will Unlock

and Interior Dome light will turn on (if installed with these optional features). LCD Pager

will beep twice while displaying an Up Arrow and an Unlock symbol followed by the CSP

logo.

Alarm Triggers:

If there is an intrusion into the vehicle, a hard impact to the body, or the ignition is turned on the alarm will

sound and flash the lights for 1 minute. After 1 minute, the trigger cycle will automatically stop and alarm will

remain armed to continue protecting the vehicle. If a door is left open after an intrusion then the unit will cycle

a maximum of 5 minutes and continue to protect the other un-tampered or unopened zones.

LCD Remote Paging / Zone Violations:

When the system is triggered, the alarm sends a paging signal to the remote. If you are within range, you will

receive a violation paging signal which consists of a vibration followed by 15 audible beeps to notify you the

vehicle has been tampered with.

DOOR TRIGGER

HOOD/TRUNK TRIGGER

SHOCK TRIGGER

IGN

(<<<< MOVING <<<<<)

IGNITION TRIGGER

OPERATING INSTRUCTIONS - ALARM

Disarming While Tripped (Triggered):

Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of

Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.

Selective Silent Arming/Disarming:

To Arm or Disarm the system without siren

chirps, press and release both Buttons #2

(Unlock) and #4 (Start) at the same time.

System will Arm or Disarm without siren chirps.

Flashing lights and LED will be the only

indicators of Arm/Disarm status. The LCD will

Display a musical note with an “X” when the

system is armed or disarmed without a chirp.

SILENT ARM

SILENT DISARM

Prior intrusion Alert

This system will notify you if the alarm was tripped while you where away. Upon disarming, the two normal

disarm chirps will be heard then the system will emit 4 additional siren chirps. Check your vehicle for any

signs of a break in or tampering. Also see LED Diagnostics Section to determine the cause of the trigger.

Remote Panic Protection

To sound the alarm in an emergency situation or to draw attention to your vehicle, press

and hold Button #1 (Lock) for at least 3 seconds until the siren sounds. Press Button #2

(Unlock) to reset panic mode. The LCD pager/remote will display a “P” and emit 15

beeps when the panic mode is triggered.

PANIC MODE

Selective Shock Sensor Disable

To arm the alarm and bypass shock sensor protection, press Button #1 as normal then

press and release Button #1 and #2 together within 2 seconds. You will hear 3 extra

siren chirps indicating shock sensor bypass for this arming cycle only. This feature can be used when parking

near railroad tracks, airports, or area with excessive loud machinery or noise to prevent the nuisance of

unnecessary false alarms.

Open Door Alert / Bypass

Upon arming, this system will warn you if a door is left open. The LCD pager will vibrate and beep (15X’s)

along with displaying the open zone on your LCD screen. This zone will automatically be bypassed until

closed, otherwise the alarm will continue to protect all other zones.

OPERATING INSTRUCTIONS - ALARM

Pre-Warning Shock Protection

PRE-WARN

The Pre-warning (warn-away) feature will activate when a low-level shock or vibration

detected by the system’s shock sensor. The alarm will chirp the siren 5 times and

flash the lights once to help deter any further tampering with the vehicle. The

pager/remote will vibrate twice and beep (15X’s).

Passive Arming Mode: (Programmable)

Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the

last door is closed. Upon closing the last door, the unit will flash the lights twice and LED will be flashing

rapidly to confirm passive countdown. If a door is reopened within the 30 second period, the countdown stop

and begin again when the door is closed. Passive arming provides failsafe protection in case you forget to

arm the system.

Passive Locking: (Programmable)

PASSIVE LOCK/ARM

The CS2016FM system can be programmed to passively lock the doors when the

system passively arms. The default setting is OFF because passive locking

increases the risk of locking the keys in the vehicle. When the system arms/locks

passively, without you pressing the remote, the LCD pager will still provide a

confirmation signal. The LCD screen will have an arrow only without a lock symbol.

Trunk/Hatch Pop (Optional, Remote AUX. Output 1)

This feature is designed to interface with existing Factory power trunk or power

hatch release systems and may require additional parts and/or labor charges.

Press and release Button #3 (Trunk) on the transmitter to pop/open the trunk/hatch.

If the system is armed, it will also disarm when the button #3 is pressed. The LCD

pager/remote will confirm with 3 beeps and the trunk icon on the screen.

TRUNK POP

Remote AUX. Output 2 (Optional, Requires special programming)

This system contains a second auxiliary output to activate other accessories or devices. To activate the

systems’ Second Auxiliary Output, press and HOLD Button #3 (Trunk Symbol) on the transmitter for more than

2 seconds. This is a momentary output that will stay active as long as the remote button is held down. There

is no LCD/pager confirmation for Aux. 2 output.

Dome Light Illumination (Optional)

This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and

turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security. 7

OPERATING INSTRUCTIONS - ALARM

Emergency Override (Disarm)

If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to

disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the

override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you

can repair/replace the remote. Valet mode also prevents Passive Arming.

Valet Mode (Enter manually or using the remote)

To disable Alarm and Remote Engine Starting for vehicle servicing or otherwise, turn the ignition on and press

the override/program button [about 5-7 seconds] until you hear (3) siren chirps and the LED turns on solid.

Repeat the process to exit VALET mode. To enter / exit valet via the remote, press and hold both buttons #1

(Lock) and Button #2 (unlock) together for about 3 seconds until 3 chirps are heard. Repeat this step to exit

via the remote transmitter. Lock/Unlock and AUX features will still operate in when in VALET mode however

remote start and alarm functions are inhibited.

Valet Park Mode (Using the remote transmitter only)

Note: Valet Park mode is only accessible when using the remote transmitter. Valet park mode allows you to

turn over the vehicle to a valet allowing access to drive/lock/unlock your vehicle, but alarm will trigger if the

trunk is opened. To activate Valet Park, press and hold both buttons #1 (Lock) and Button #2 (unlock)

together for about 6 seconds. 3 chirps will be heard first when unit goes into regular Valet and as you

continue to hold both buttons you will hear 2 more chirps. LED will always flash slowly when in Valet Park

even when the Ignition is turned on (or driving vehicle). Repeat step above to exit Valet Park mode.

ALET UNLOCK

ALET LOCK

VALET MODE

Optional M.A.P. (Mobile Accessories Protection)

This system can be programmed to provide Crimestopper’s unique M.A.P. (Mobile Accessories Protection) feature that

allows you to prevent unauthorized access of your vehicles Audio, Cellular, Navigation, or Entertainment systems.

This feature is OPTIONAL and requires extra parts and labor for installation. Consult your installation dealer about

MAP before or during installation. The CS2016FM must be programmed for MAP operation. When the system is put

into Valet Park mode, M.A.P. will prevent stereo, entertainment, navigation, or cellular system from being used.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING - SUCCESSFUL START

1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation.

(Chirps can be programmed on or off-See installation manual.)

2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on.

3) After a few seconds, Starter Motor engages, Parking lights and Accessory circuits turn off while cranking.

4) Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock.

5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can

be turned off with remote transmitter.

REMOTE ENGINE STARTING - SUCCESSFUL START DIAGRAM:

AFTER

IGN

STARTER

THEN

FLASH 1X

SOLID

SEC.

START

IGN

CONFIRM REMOTE

START REQUEST

REMOTE ENGINE STARTING – LCD PAGER-REMOTE:

IGN

(<<<< MOVING <<<<<)

SUCCESFUL START

When requesting a remote start the LCD pager remote

will confirm with an Ignition Icon along with 4 beeps.

Once the vehicle has successfully started the remote will

confirm back with 2 vibrations, a moving vehicle Icon, and

4 beeps.

REMOTE ENGINE CONTROL

UNSUCCESSFUL REMOTE START

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then

attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank

time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to

13 seconds to help prevent damage to the starter from over cranking.

1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 (on last page) under "Successful Start".

2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER

ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON

AGAIN.

TURNING OFF YOUR REMOTE STARTED ENGINE (VIA REMOTE CONTROL):

1) Engine is running in Remote Start (Parking lights ON).

2) Press Remote Start button on remote transmitter.

3) Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable.

ENGINE & LIGHTS OFF

START

ENTERING YOUR REMOTE STARTED VEHICLE:

1) With engine running, Remote Unlock/Disarm system (If armed) or open door with key.

2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)

3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter & Shift out of park.

4) Remote starter will reset instantly when the brake is pressed. Parking lights will turn off and the ignition key

is now controlling your vehicle. 10

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper CS-9206SE Handbuch

CrimeStopper

CrimeStopper SP-500 Systemhandbuch

CrimeStopper

CrimeStopper CS-2205 Handbuch

CrimeStopper

CrimeStopper CS-8700 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9711 Systemhandbuch

CrimeStopper

CrimeStopper Super Page V CS-2014TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2000DP-TW2 Handbuch

CrimeStopper

CrimeStopper SP-300 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2000DPII TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper HP-9235MX Kurzanleitung

CrimeStopper

CrimeStopper Fortress FS-30 Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4011 Stücklistenhandbuch

CrimeStopper

CrimeStopper Fortress FS-10 Handbuch

CrimeStopper

CrimeStopper CS-9200 Samurai Bedienungsanleitung

CrimeStopper

CrimeStopper SuperPage III CS-2006FM Montageanleitung

CrimeStopper

CrimeStopper CoolStart RS-1604TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9228MX Handbuch

CrimeStopper

CrimeStopper CS-9709 Kurzanleitung

CrimeStopper

CrimeStopper CS-2002DC Series III Bedienungsanleitung

CrimeStopper

CrimeStopper Super Rage CS-2012TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9602PI Betriebsanleitung

CrimeStopper

CrimeStopper SP-100 Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung