Insportline HG1092B Bedienungsanleitung

HG1092B

OWNER'S MANUAL

ASSEMBLY INSTRUCTIONS

1) SAFETY INSTRUCTIONS

IMPORTANT!

·This machine is made for home use only and tested up to a maximum body weight of 100 kg.

·This training device should be used only for its intended purpose. Any other use is prohibited and

dangerous. The manufacturer cannot be held liable for damage or injury caused by improper use of

the equipment.

CAUTION!

1. You are using a machine that has been designed and built to the latest safety standards. Any

possible sources of danger that could lead to injury have been extensively eliminated. The machine

is intended for use by adults only.

2. Wrong or excessive training can damage your health. Before commencing a course of fitness

training, arrange for a medical check-up to see if you are in a state of health suited to training on the

machine. The result of the check-up should be used as a basis for your training pr0gram.

3. The machine is never to be looked upon as a toy. Please remember that the nature of children who

are using the machine can lead to unforeseen situations and hazards for which the manufacturer

cannot be held liable.

4. If children are allowed to use the machine, they should be instructed on its correct use and

dangerous situations explained to them.

5. The machine must be carefully assembled by an adult. Place it on a flat and strong ground. It must

be ensured that the machine is not used until it has been fully assembled.

6. When used for regular training/exercising, we recommend checking all parts of the machine

(especially screws, nuts, bolts and ropes) every 1 to 2 months.

7. To maintain the intended level of safety the machine is to be taken out of use if any parts are worn.

The worn parts are to be exchanged immediately.

8. Make sure that no adjustment device is left projecting.

9. Please always wear proper training clothes and shoes.

2) PACKAGING

Environment-friendly and recyclable materials:

Outer packing cardboard

Formparts are made of Polystyrol (PS) No FCKW

Foils and bags are made of PE

Girths are made of PP

3) DISPOSAL

Please dispose packaging properly. Don’t put it in the garbage.

4) PARTS LIST

PARTS LIST

PART NO. DESCTIPTION Q'TY

1 BASE FRAME 1

2 REAR STABILIZER 1

3 REAR SUPPORT 1

4 FOOT PLATE 1

5 SUPPORT BRACKET 1

6 LOWER UPRIGHT 1

7 UPRIGHT 1

8 LEVER ARM 1

9 SEAT FRAME 1

10 LEG LIFT 1

11 SEAT POST 1

12 BACK SUPPORT 1

13 ADJUSTMENT BAR 1

14 SLIDER SUPPORT 1

15 FOAM SUPPORT 2

16 ARM BRACE 1

17 LEFT LEVERAGE ARM 1

18 RIGHT LEVERAGE ARM 1

19 WEIGHT BAR 2

20 LEFT HANDLEBAR 1

21 RIGHT HANDLEBAR 1

22 HANDLEBAR SUPPORT 2

23 LAT BAR 1

24 STRAIGHT BAR HANDLE 1

25 SUPPORT TUBE 2

26 JOINT PLATE 1

27 JOINT PLATE 1

28 JOINT PLATE 2

29 LARGE WASHER 2

30 HEAD REST 1

31 BACK CUSHION 1

32 SEAT CUSHION 1

33 FOAM ROLLER 6

34 RUBBER STAND 3

35 AB CURL STRAP 1

36 90MM PULLEY 8

37 SQUARE PLUG 25*25 4

38 CABLE 1

39 SHORT CABLE 1

40 FAST PIN 2

PARTS LIST

PART NO. DESCTIPTION Q'TY

41 BUMPER 2

42 QUINCUNX NUT 1

43 HANDLEBAR CAP 6

44 SPRING CLIP 4

45 SQUARE CAP 1

46 RECTANGULAR PLUG 50*25 1

47 RECTANGULAR PLUG 70*50 1

48 SQUARE PLUG 38*38 2

49 SQUARE PLUG 50*50 9

50 ROUND PLUG 4

51 SECURING CAP 6

52 SQUARE SLEEVE 4

53 BUSHING 2

54 LONG BUSHING 2

55 BUSHING 38-19 8

56 QUICK LINK 4

57 CHAIN 1

58 CABLE SLIDE 10

59 PIN 2

60 HEXAGON SOCKET BOLT M8*16 10

61 BOLT M10*16 + WASHER 10

62 BOLT M10*45 2

63 BOLT M10*50 + WASHERS + NUT 7

64 BOLT M12*70 + WASHER 1

65 BOLT M10*70 + WASHERS + NUT 1

66 BOLT M10*80 + WASHERS + LOCK NUT 2

67 BOLT M10*90 + WASHERS + NUT 1

68 BOLT M10*100 + WASHERS + LOCK NUT 1

69 BOLT M12*20 + LARGE WASHER 4

70 BOLT M12*65 + WASHERS + NUT 4

71 BOLT M12*75 + WASHERS + LOCK NUT 1

72 BOLT M12*75 + WASHERS + NUT 6

73 BUSHING 50-10 2

74 BOLT M12*105 + ARC WASHERS + NUT 2

75 BOLT M12*130 + WASHERS + LOCK NUT 1

76 BOLT M12*140 + WASHERS + LOCK NUT 1

77 ANKLE CUFF 1

78 BOLT M12*70 + WASHERS + NUT 1

79 PULLEY BRACKET 1

80 SMALL QUICK LINK 1

81 120MM PULLEY 1

5) ASSEMBLY INSTRUCTION

STEP 01

1. Attach the foot plate (4) to the base frame (1) with bolt M10*100 + washers + lock nut (68).

2. Bolt the base frame (1), rear stabilizer (2), and rear support (3) together with bolt M12*105 +

arc washers + nut (74).

3. Attach the lower upright (6) and the support bracket (5) to the base frame (1) with bolts

M12*65 + washers + nut (70). Attach the lower upright (6) to the rear stabilizer (2) with bolts

M12*65 + washers + nut (70).

4. Attach the lever arm (8) to the lower upright (6) with bolt M10*80 + washers + lock nut (66).

Do not over tighten the bolt, as the lever arm (8) must be able to pivot smoothly. Slide the spring

clip (44) onto both sides of the lever arm (8).

5. Attach the pulley bracket (79) to lower upright (6) with quincunx nut (42).

STEP 02

6. Run the half ball end of the cable (38) through the slot at the top end of the upright (7). Attach the cable to

the upright (7) at "A" with the 120mm pulley (81), long bushing (54), bolt M10*90 + washers + nut (67).

Run the cable (38) through the pulley bracket on the upright (7) at "B". Attach the cable (38) to the pulley

bracket with a pulley (36), two cable slides (58), bolt M10*50 + washers + nut (63).

7. Insert the upright (7) into the lower upright (6). Do not attach the bolts yet. Attach the cable (38) to the

pulley bracket on the lever arm (8) at "C" with a pulley (36), two cable slides (58), bolt M10*50 + washers +

nut (63). Run the cable (38) through the upright (7) and lower upright (6). Attach the cable (38) to the pulley

bracket at "D" with a pulley (36), a cable slide (58), bolt M10*50 + washers + nut (63). Repeat at position "E".

Attach the cable (38) to the pulley bracket at "F" with a pulley (36), two cable slides (58), bolt M10*50 +

washers + nut (63). Attach the cable (38) to the bracket at "G" with a pulley (36), two cable slides (58), blot

M10*50 + washers + nut (63).

8. Secure the upright (7) to the lower upright (6) with bolts M10*16 + washers (61).

9. Attach the seat frame (9) and the joint plate (27) to the lower upright (6) with bolt M12*70 + washer (64)

and bolt M12*70 + washers + nut (78).

10. Attach the leg lift (10) to the seat frame (9) with bolt M10*80 + washers + lock nut (66). Run the cable (38)

through the slot in the leg lift (10). Attach the cable (38) to the leg lift (10) with a pulley (36), bushing (53),

bolt M10*70 + washers + nut (65).

STEP 03

11. Attach the slider support (14) to the lower upright (6) with bolt M12*140 + washers + lock

nut (76). Do not over tighten the bolt, as the slider support (14) must be able to pivot smoothly.

12. Pull the fast pin (40) on the slider support (14). Then insert the adjustment bar (13) into the

slider support (14) and lock in the top adjustment hole with the fast pin (40).

13. Attach the back support (12) to the lower upright (6) with bolt M12*75 + washers + lock nut

(71). Attach the back support (12) to the adjustment bar (13) with bolt M12*130 + washers +

lock nut (75). Do not over tighten the bolt (71,75), as the back support (12) must be able to pivot

smoothly.

14. Attach the arm brace (16) and the joint plate (26) to the lower upright (6) with bolts M12*75

+ washers + nut (72).

15. Attach the foam support (15) to both sides of the lower upright (6) with bolts M10*16 +

washers + nut (61).

16. Pull the fast pin (40) on the seat frame (9). Then insert the seat post (11) into the seat frame

(9) and lock it in one of the adjustment hole with the fast pin (40).

STEP 04

17. Slide the right leverage arm (18) onto the shaft at right side of the arm brace (16) and secure with bolt

M12*20 + large washer (69).

18. Attach the weight bar (19) and the joint plate (28) to the right leverage arm (18) with bolts M12*75 +

washers + nut (72). Slide spring clip (44) onto the weight bar (19). NOTE: When installing the right weight bar

(19), be sure they angle up and toward rear of the machine.

19. Attach the right handlebar (21) to the handlebar support (22) with pin (59). Then slide the handlebar

support (22) into the large washer (29) and the right leverage arm (18) and secure with bolt M12*20 + large

washer (69).

20. Repeat the above assemblies for left side.

21. Attach the head rest (30) and back cushion (31) to the back support (12) with bolts M8*16 (60).

22. Attach the seat cushion (32) to the seat post (11) with bolt M8*16 (60).

Inhaltsverzeichnis

Andere Insportline Fitnessgeräte Handbücher

Insportline

Insportline IN 7120 Bedienungsanleitung

Insportline

Insportline IN 7773 VibroGym Pyrio Bedienungsanleitung

Insportline

Insportline Hero B100 Bedienungsanleitung

Insportline

Insportline 18259 Bedienungsanleitung

Insportline

Insportline IN 1866 Bedienungsanleitung

Insportline

Insportline IN 18538 Bedienungsanleitung

Insportline

Insportline 16491 Bedienungsanleitung

Insportline

Insportline IN 152 OMEGUS Bedienungsanleitung

Insportline

Insportline Body Solid Fusion FCD Bedienungsanleitung

Insportline

Insportline VibroGym Lilly Bedienungsanleitung

Insportline

Insportline LCR1103 Bedienungsanleitung

Insportline

Insportline PW200 Bedienungsanleitung

Insportline

Insportline AB Perfect Bedienungsanleitung

Insportline

Insportline RK92 Bedienungsanleitung

Insportline

Insportline W-tec WARMelong Bedienungsanleitung

Insportline

Insportline IN 12075 Bedienungsanleitung

Insportline

Insportline Askepot Bedienungsanleitung

Insportline

Insportline IN 10554 Bedienungsanleitung

Insportline

Insportline Power Tower PT250 Bedienungsanleitung

Insportline

Insportline Sinderelo Bedienungsanleitung

Insportline

Insportline IN 21393 Bedienungsanleitung

Insportline

Insportline Airincline IN 23350 Bedienungsanleitung

Insportline

Insportline 18250 Bedienungsanleitung

Insportline

Insportline VibroGym Charles Bedienungsanleitung

Beliebte Fitnessgeräte Handbücher anderer Marken

NSD

NSD PB-188P Bedienungsanleitung

Performance

Performance HyperVibe Bedienungsanleitung

Scalamobil

Scalamobil S27 Bedienungsanleitung

Precor

Precor Experience Series Bedienungsanleitung

FYTTER

FYTTER RedMIUM BENCH BE-T6R Bedienungsanleitung

Taurus

Taurus TF-RK1312 Bedienungsanleitung

Nustep

Nustep T5 Bedienungsanleitung

Precor

Precor CW-507 Bedienungsanleitung

Movement

Movement BICEPS Idea Bedienungsanleitung

Kegel8

Kegel8 V For Men Bedienungsanleitung

BLK BOX

BLK BOX 21-0122-0B Bedienungsanleitung

Stamina

Stamina aeropilates premier 299 Bedienungsanleitung

SPORTSTECH

SPORTSTECH PBX300 Bedienungsanleitung

ParaBody

ParaBody Serious Steel 877102 Bedienungsanleitung

Weslo

Weslo Gym 650 Bedienungsanleitung

Rebel

Rebel ACTIVE RBA-1011 Bedienungsanleitung

4iiii

4iiii FLiiiight Bedienungsanleitung

Image

Image 540 Bedienungsanleitung