Oneida Air Systems Supercell Mobile Bedienungsanleitung

U.S. Patent: #8393050,

#8377160, #9125535,

#D917806

Supercell®

Supercell® Turbo

High-Pressure

Dust Collector

14 Gallon

# XSK000014

# XSK414000

Rev: B 20221128LL Doc. #ZBM000037

Appearance may vary slightly

OWNER’S MANUAL

READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNING LABELS BEFORE

USING THE DUST COLLECTOR.

oneida-air.com 1

Table of Contents

System Start-Up Information 2

Supercell/Supercell Turbo System Specications 6

System Dimensions 7

System Contents 8

Assembly Instructions 10

Maintenance 22

Troubleshooting 24

F.A.Q. 26

Recommended Accessories 27

Warranty Information 29

Oneida Air Systems, Inc.2

System Start-Up Information

 WARNING 

1. READ and understand ALL instructions and warning labels BEFORE using the dust collector.

2. REPLACE warning labels if they become obscured or removed.

3. ALWAYS follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and

regulations when installing and operating this dust collector.

4. ENSURE that all users of this Dust Collector are informed of all warnings and precautions, safe use, and

maintenance procedures.

5. FULL mental alertness is required. NEVER operate under the inuence of drugs or alcohol, when tired, or

when distracted.

6. DO NOT allow use by or near children.

7. DO NOT allow to be used as a toy. Close attention is necessary when used by or near children.

8. NEVER leave the dust collector running while unattended.

9. TURN OFF and UNPLUG the dust collector BEFORE walking away, servicing, or cleaning. Allow the fan

blower motor to come to a COMPLETE STOP before walking away or performing any maintenance, service,

cleaning, or adjustments. is eliminates the risk of injury from unintended startup or contact with live

electrical components.

10. ENSURE that your dust collector is turned OFF and UNPLUGGED during installation. is eliminates the

risk of injury from unintended startup or contact with live electrical components.

11. COMPLETELY INSTALL ductwork/ex hose before operating collector.

a. Seal ductwork with silicone sealant or duct tape if leaks are found.

b. Have dust drum in place and sealed.

c. NEVER operate without lter and cowling in place. is machine has high speed rotating elements than

can cause severe injury.

12. ONLY use the dust collector for its intended purpose as described in this manual. DO NOT force it or

an attachment to do a job for which it was not designed. Consult this owner’s manual or reach out for

recommended accessories.

13. ENSURE enough air volume is at the suction point to capture all the particulate generated.

Before Purchasing or installing a dust collection system the process owners/operators

are cautioned to do so in accordance with prescribed Federal, State, Local, OSHA, NFPA,

and any other applicable codes or regulations relating to the type of dust(s) you are

collecting.

This manual contains specific precautionary statements relative to worker safety. Read

thoroughly and comply as directed. The most up to date safety information can be found

on our website: oneida-air.com/safety

oneida-air.com 3

System Start-Up Information (Continued)

14. NEVER make modications without prior approval from Oneida Air Systems. Modifying the dust collector

or using it dierently than intended will void the warranty and may result in malfunction or mechanical

failure that leads to serious personal injury or death!

15. DO NOT locate or operate the system in moist, wet, poorly lit, or cluttered environments. Operating in these

areas can create shock hazards, increase the risks of accidents and injury, and/or lower the operating lifespan

of the dust collector.

16. DO NOT install in classied hazardous atmospheres without an enclosure rated for the application. System

Location must account for wind, seismic zone, and other load conditions. Codes may regulate acceptable

locations for installing dust collectors. Consult with the appropriate authorities having jurisdiction to ensure

compliance with all national and local codes regarding dust collector installation. Equipment must be

anchored in a manner consistent with local code requirements. Anchors must be sucient to support dead,

live, seismic, and other anticipated loads. Consult a qualied engineer for nal selection of anchorage.

17. ENSURE exhaust air is properly vented. It should NOT be vented into a wall, a ceiling, or a concealed space

of a building. Personal injury, death, and/or property damage can result from material discharge during

venting. e risk of personal injury and/or property damage can be minimized or avoided by locating vented

equipment outside buildings and away from normally occupied areas. If exhaust air is vented outside, you

must provide make up / return air. Flue gases (carbon monoxide) can be drawn into the shop from furnaces,

water heaters, or other appliances

18. INSPECT and MAINTAIN REGULARLY. Keep the dust collector in proper working order. A machine that

isn’t properly maintained, not working as it should, has been dropped, damaged, le outdoors, or dropped in

water could malfunction leading to serious personal injury or death!

19. AVOID CORD DAMAGE. DO NOT pull or carry by cord. DO NOT use cord as handle. DO NOT unplug

by pulling on cord. To unplug, grab the plug, DO NOT close door on cord or pull cord around sharp edges or

corners. DO NOT run dust collector over cord. DO NOT handle cord/plug with wet hands. Keep cord away

from heated surfaces.

20. ALWAYS check for damaged parts. A part that is damaged should be carefully checked to determine that

it will operate properly and perform its intended function. Immediately repair or replace damaged or mis-

adjusted parts before operating machine.

21. DO NOT put any object in openings. DO NOT use with any opening blocked. (Except when pulsing - See

Maintenance Section for more information.)

22. ALWAYS wear a NIOSH approved respirator when emptying dust bins and during operation. Some dust

created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals

known to cause cancer, birth defects or other long-term respiratory damage

23. ALWAYS keep hair, loose clothing, ngers, and all parts of body AWAY from openings and moving parts.

24. ALWAYS wear ANSI-approved safety glasses or a face shield when operating or observing machinery and

when emptying dust bin.

25. ALWAYS wear hearing protection during extended periods of operation.

Oneida Air Systems, Inc.4

System Start-Up Information (Continued)

1. THIS UNIT IS NOT RATED FOR USE IN COMBUSTIBLE ENVIRONMENTS.

2. DO NOT operate the dust collector in areas where explosion risks are high. Areas of high risk include, but

are not limited to, areas near pilot lights, open ames, or other ignition sources.

3. ONLY operate dust collector in locations that include a re suppression system or have a re extinguisher

available nearby.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire

Extinguishers).

4. DO NOT allow accumulation of layers of ne dust on horizontal surfaces. Especially overhead lights,

electrical boxes and fuse panels which can ignite dust. Keep the oor around the system clean and free of

scrap material, oil, grease.

5. ENSURE all equipment and ductwork is electrically grounded.

6. DO NOT use PVC drain pipe.

7. ALWAYS consult an electrician or qualied service personnel about wiring practices and electrical codes

in your area. ONLY allow an electrician or qualied service personnel to do electrical installation or repair

work.

8. ALWAYS disconnect power before accessing or exposing electrical equipment. Improper wiring can cause

re, electrocution, injury, or death.

9. DO NOT use to pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

10. DO NOT use to pick up liquids, ammable liquids, or combustible liquids, such as gasoline, or use in areas

where they may be present.

11. DO NOT use excessively large wood waste bins. Wood dust mixtures are highly ammable and can be

explosive

 FIRE HAZARDS 

Process owners/operators retain all responsibility for the suitability of fire and explosion

hazard mitigation, suppression, and isolation strategies and to follow all applicable

federal, state, local, OSHA, NFPA, or authorities having jurisdiction codes and regulations

when installing and operating this dust collector.

Improper operation of a dust control system may contribute to conditions in the work

area or facility that could result in severe personal injury and product or property

damage.

Oneida Air Systems assumes no responsibility or liability for the suitability of any fire and/

or explosion mitigation strategy, or any items incorporated into a collector as part of an

owner/operators hazard mitigation strategy.

oneida-air.com 5

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

System Start-Up Information (Continued)

12. ALWAYS check your dust bin for smoldering materials before leaving the shop.

13. NEVER introduce sparks or sources of ignition into the dust collector. Sparks can be generated in several

ways:

a. High speed sanders, abrasive planers, saws, and edgers may strike foreign material and create a red-hot

metal fragment.

b. Knots in hardwood can create frictional sparks.

c. Trapped metal, when drawn into the dust collection system, can spark against ductwork.

d. Check wood stock for old nails and screws which can create red-hot metal fragments.

14. DO NOT overload woodworking equipment, especially sanders, as excessive frictional heat can

spontaneously ignite dust. Sanders can produce concentrations of dust well into the combustible range.

15. ALWAYS check that all dust collection equipment is properly selected and sized for the intended use.

Authorities with jurisdiction should be consulted before installing to verify local codes and installation

procedures. In the absence of such codes, install collector according to the National Electric Code, NFPA No.

70-latest edition and NFPA 91, NFPA664 Code (NFPA 654 if combustible dust is present).

Oneida Air Systems, Inc.6

Supercell/Supercell Turbo System Specications

OPERATION

Maximum Suction Rating 97.8" WC

MOTOR AND ELECTRICAL

Motor Type 3x 1300W Modular Motors/ 4x 1300W Modular Motors

Horsepower 5HP Total / 6.7 HP Total

Motor Speed 48,880 RPM

Phase 1-Phase

Voltage 208-230V

Cycle 60HZ

Listed FLA 18A / 22A

On/O Switch Magnetic Starter with On-O Switch and RF Remote

Power Cord Length 10 feet

Power Connector NEMA 6-20 / BareWiring

Recommended Circuit Size 20A / 30A

Recommended Circuit Type HACR

Sound Emission 80 dBA @ 10 ft / 85 dBA @ 10 ft

CARTRIDGE FILTER

Filter Media Type HEPA Certied

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 40 sq ft

SYSTEM DIMENSIONS AND CONSTRUCTION

Primary Build Materials Cold Rolled Steel, Static Dissipative Polyethylene

Inlet 4" O.D.

Discharge to Drum 5" O.D.

Overall Height 14 Gallon: 61"

Overall Weight 14 Gallon: 76 lbs

e Supercell requires a 20 Amp

outlet receptacle to be installed by a

licensed electrician.

Bare Wiring

Two HotWires & Ground

Licensed Electrician

REQUIRED

Bare Wiring

Two HotWires & Ground

Licensed Electrician

REQUIRED

e Supercell Turbo requires that

it be installed to a 30 Amp breaker

(minimum) by a licensed electrician.

23.119

oneida-air.com 7

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing. Mounting dimensions allow for

13/16" clearance when removing and emptying the drum

Allow for an additional 24" of clearance above the Motor Assembly to allow for its removal during lter replacement and

other maintenance. Allow for an additional 3" of clearance around the system for ease of access to the latches.

System Dimensions

13/16"

21 mm

36-13/16"

935 mm

Floor

21-9/16"

548 mm

20"

508mm

23"

587mm

24-1/4"

616 mm

61"

1,549 mm

Oneida Air Systems, Inc.8

System Contents

Please unpack the parts carefully and conrm you have received each item listed here.

* Some components are pre-installed at the factory and are listed here for your convenience.

ID Part number Part description Qty

ABXI001501

BXI441501

Supercell Motor Assembly

SupercellTurbo Motor Assembly 1

B FPX040001 Filter Hold Down Plate 1

C FCS131040H 13" x 13" Conical HEPA Cartridge Filter 1

D GCZ150000 15" Ring Clamp 1

E SCX040000 Cyclone 1

E1* DGA040000 4" Aluminum Blast Gate 1

E2* DAB040000 4" Male Duct Adapter 1

E3* AFR316066 Rivets 5

F SMS040001 Supercell Wall Bracket 1

G AHX000021 Supercell 14 Gal. Model Hardware Pack 1

G1 ZBT040001 Supercell Wall Bracket Template 1

G2 RGF000015 15" Barrel Gasket 1

G3 RGZ051820 Supercell Flange Gasket 1

G4 AFS015920 1/4"-20 x 3/4" Hex Head Bolt 6

G5 AFW025000 1/4" Flat Washer 6

G6 AFT900006 1/4"-20 Nylock Nut 6

G7 AFB155180 5/16-18 x 2-1/2" Hex Head Bolt 4

G8 AFW180000 5/16" Flat Washer 4

G9 AFW180516 5/16”Rubber Washer 4

G10 AFT155175 5/16 " Whiz-Lock Nut 4

G11 AFT900516 5/16" - 18 Nylock Nut 4

G12 AFW516075 5/16x 3/4" Nylon Spacer 1

G13 SMS040000 Rear Support Brace 1

G14 AFL990001 Latches 2

G15 AFS501032 10-32 1/2" Phillips Pan Head Screws 4

G16 AFT901032 10-32 Nylock Nut 4

ID Part number Part description Qty

G17 AFB155180 5/16-18 x 2-1/2" Hex Head Bolt 2

G18 AHX000033 Tubing Assembly 7

G18A VRV050500 1/2" ID Clear Vinyl Tubing 1/3'

G18B AWV000050 1/2" ID SwitchValve 1

G18C VRV050500 1/2" ID Clear Vinyl Tubing 7'

G19 ACH000058 Double Spring Clamp 1

G20 AHX000018 Quick Disconnect Kit 1

G20A RLH000006 1/4" NPT Nylon Elbow 1

G20B RLH000005 3/8”Socket 1

G20C RLH000004 3/8" Male Plug 1

G20D RLH000002 Nylon Washer 1

G20E RLH000003 Rubber O Ring 1

G20F RLH000007 Nylon Nut 1

G21 AXD600300 9-17 Gallon Drum Liner Bag 5

G22 RLH000023 23 mm Button Plug 1

G23 ACB640000 4-1/2" Turn-Key Band Clamp 2

G24 RGZ470114 Bin Gasket 4

G25 AMR000000 Remote Control Key Fob 1

H DHF042502 4" x 25' Vacuum Pressure Rated Flex-Hose 1

I AXB999110B Dust Sentry Automatic Bin Level Indicator 1

J SMD140400 Drum Assembly 1

J1 SDS140000 14 Gallon Molded Drum 1

J2* RHL000604 Drum Window 1

J3* AFS103258 10-32 5/8" Phillips Pan Head Screws 4

J4* AFT901032 10-32 Nylock Nuts 4

J5 RHC000012 3" Caster with 5/16"-18 x 3/4" Stems 5

If you cannot find an item on the list, examine the packaging materials very carefully for nested items. Please

note that certain components have been pre-installed. There may be hardware leftover.

Andere Handbücher für Supercell Mobile

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2 HP Commercial Cyclonic Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop DC Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000014 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK050100 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V - 2000 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK100300 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2005c3HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD002030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung