Oneida Air Systems Dust Cobra Bedienungsanleitung

Rev: 01/13/2020 Doc. #ZBM000025B

Appearance may vary slightly

U.S. Patent: #8,377,160

U.S. Patent #9,125,535 B2

U.S. Patent: #8,377,160

U.S. Patent #9,125,535 B2

OWNER’S MANUAL

Dust Cobra

Dust Collector

Standard /Industrial/Vortex

#XCKM010000

#XCKM013500

#XCKM010000-IND

#XCKM013500-IND

#XCKM010000-VOR

#XCKM013500-VOR

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 4

System Dimensions 6

System Contents 8

Industrial and Vortex Contents 10

Assembly Instructions 12

Vortex Assembly Instructions 19

Filter Pulse Bar Cleaning 22

Maintenance 23

Troubleshooting 24

Warranty Information 25

Recommended Accessories 26

Notes 28

2 Oneida Air Systems

System Start-Up Information

1. is unit is NOT rated for use in combustible environments.

2. DO NOT leave dust collector plugged in. Turn o all controls before unplugging. Unplug from outlet when not in use and

before servicing.

3. DO NOT use outdoors or on wet surfaces.

4. Use only as described in this manual. DO NOT allow use as a toy. DO NOT allow use by or near children.

5. DO NOT use with damaged cord or plug. If dust collector is not working as it should, has been dropped, damaged, le

outdoors, or dropped in water, return to service provider.

6. DO NOT pull or carry by cord. DO NOT use cord as handle. DO NOT close door on cord or pull cord around sharp edges

or corners. DO NOT run dust collector over cord. Keep cord away from heated surfaces. DO NOT unplug by pulling on

cord. To unplug, grasp the plug, not the cord.

7. DO NOT handle plug or dust collector with wet hands.

8. DO NOT put any object in openings. DO NOT use with any opening blocked except when pulsing. (See Maintenance

Section for more information.)

9. Keep free of dust, lint, hair, and anything that may reduce air ow.

10. Keep hair, loose clothing, ngers, and all parts of body away from openings and moving parts.

11. DO NOT use to pick up liquids, ammable liquids or combustible liquids, such as gasoline, or use in areas where they may

be present.

12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

13. is machine has high speed rotating elements than can cause severe injury. NEVER operate without lter and cowling in

place. Unplug unit before removing motor head for service or lter cleaning.

14. Dust can be ammable and explosive. Some dust can be toxic or cause allergic reactions.

15. Wire according to all applicable codes. Improper wiring can cause electrocution or re. e motor must be properly

grounded. If permanently installed, use individual branch circuit.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings, and dust. ese materials are considered combustible.

Air borne wood dust below 500 microns in size (.017 of an inch) in certain concentration ranges can deagrate (when

ignited). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame front, which

can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise additional

dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been witnessed,

it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

Make sure to read and understand the installation and maintenance instructions as well as all

recommended safety practices.



3oneida-air.com

System Start-Up Information (Continued)

codes and regulations when installing and operating this dust collector.

b. Before Purchasing or Installing a dust collection system the buyer is cautioned to do so in accordance with prescribed

Federal, State, Local, OSHA, NFPA, and any other applicable codes or regulations relating to the type of dust(s) you are

collecting.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!

5. NEVER collect sparks from a bench grinder into a wood dust collector.

6. NEVER introduce sparks or sources of ignition into the dust collector.

7. Check dust bin frequently for smoldering material and before leaving the shop.

8. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

9. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

10. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

11. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals

known to cause cancer, birth defects or other reproductive harm. Your risk from these exposures varies, depending on how

oen you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area, and work with

approved safety equipment, such as those dust masks that are specially designed to lter out microscopic particles. Oneida

Air Systems recommends using additional approved safety equipment such as an approved OSHA and NIOSH dust mask or

respirator. Some examples of these chemicals are:

a. Lead from lead-based paints.

b. Crystalline silica from bricks, cement and other masonry products.

c. Arsenic and chromium from chemically-treated lumber.

12. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

13. Empty dust bin and clean lter oen, especially when sanding.

14. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

15. UNPLUG UNIT BEFORE SERVICING, REMOVING BLOCKAGES, OR CLEANING.

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4 Oneida Air Systems

System Specications

OPERATION

Fan Rating (Free Fan) 245CFM

Fan Rating (with Cyclone & Filter) 245 CFM @ 23" WC - Maximum Flow Rate

202 CFM @ 34" WC - with 25’of 2.5"diameter ex hose

Maximum Suction Rating 70" WC

MOTOR AND ELECTRICAL

Motor Type UL listed Industrial motor

Voltage 110V

Amperage 15.5A

Power Cord Length 20'

Power Plug Included Yes

Power Plug Type 110V: NEMA

Recommended Circuit Size 20A

Sound Emission With Standard Silencer & Filter: 73 dBA @ 10 ft

CARTRIDGE FILTER

Filter Type GORE Cleanstream® HEPA Filters

Filter Rating 99.97% ltration eciency at 0.3 microns (µm)

Pulse Type Manual Internal Rapid Pulse Filter Cleaner System

Pulse Interval ~30 Minutes or as needed based on the situation

SYSTEM DIMENSIONS AND CONSTRUCTION

Cyclone Body Industrial, Static Conductive Resin

Inlet Size 2.5" O.D. (2.25" I.D.)

Inlet Dimensions 2.3" ID

Drum Type Reinforced Steel Drum with Painted Exterior

Container Size 17 Gallons/35 gallons

Overall Height 17 Gallon: 53.5" / 35 Gallon: 59.25"

Drum Dolly Height Add 4-7/8"

Overall Weight 17 Gallon: 45 lbs // 35 Gallon: 55.8 lbs

5oneida-air.com

System Specications

WARNING

This motor can expose you to chemicals,

including carbon black, which is known to

the State of California to cause cancer.

For more information go to

www.P65Warnings.ca.gov

Keep the Certicate of Compliance on hand while doing lead remediation

6 Oneida Air Systems

System Dimensions with 17 Gallon Drum

Note: Drum Dolly adds 4.25" (108 mm) to height.

Larger casters add 1/2 (25 mm) to height.

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

53 - 1/2"

1359 mm

31-1/4"

794 mm

to center

of inlet

53.5"

1359 mm

18.25"

464 mm

16.5"

419 mm

7oneida-air.com

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

System Dimensions with 35 Gallon Drum

59-1/4"

1505 mm 37"

940 mm

to center

of inlet

37"

939.8 mm

22"

559 mm

22-1/4"

565 mm

Note: Drum Dolly adds 4.25" (108 mm) to height.

Larger casters add 1/2" (25 mm) to height.

8 Oneida Air Systems

System Contents

Please unpack the parts carefully and conrm you have

received each item listed here.

ID Part number Part description Qty

ABXI001205H

BXI001205F35

110V Cobra Motor Assembly for 17 Gal

110V Cobra Motor Assembly for 35 Gal

B SCX001205D Molded Cobra Cone Assembly 1

C FCH000004 GORE® CleanStream Pro HEPA Filter 1

DSES170002

SES350005

17 Gal Steel Drum Kit

35 Gal Steel Drum Kit

ESEX170400A

SEX350400A

17 Gal Drum Lid

35 Gal Drum Lid

FAHX001205D

AHX001205F35

17 Gallon Cobra Hardware Kit

35 Gallon Cobra Hardware Kit

F1 STP000006 Handle Plate 2

F2 AFB155175 5/16"-18 x 3/4" Hex Head Bolt 2

F3 AFW180000 5/16" Flat Washer 2

F4 AFW180516 5/16" Rubber Washer 2

F5 AFT900516 5/16" - 18 Nylock Nut 2

F6 RHS009043 Webbing Handle 2

F7 RBB000003 Struts 3

F8 AFS015920 1/4”-20 X 3/4" Hex Head Bolt 3

F9 AFB250125 1/4"-20 x 1 1/4" Carriage Bolt 3

F10 AFW180516 5/16" Rubber Washer 6

F11 AFW025000 1/4" Flat Washer 12

F12 AFT000005 1/4" Whiz-Lock Nut 6

F13 AFT000006 1/4"-20 Thumb Nut 1

F14 VSC001205 Velcro Tie Straps 1

F15 RHS000000 Vacuum Hose Storage Strap 1

F16 AFJ051602 5/16"-18 x 2" J Bolt 2

F17 AFT155175 5/16" Whiz-Lock Nut 2

F18 RHS000010 Filter Retainer Strap 1

ID Part number Part description Qty

F19 AFS501032 #10 Phillips Drive Pan Head Screw 2

F20 AFW200000 #10 Washer 2

F21 AFT901032 10-32 Nylock Nut 2

F22 AXD000006 1" Hook Tape .16 ft

F23 AXD000007 1" Loop Tape .16 ft

F24 AFL001205 Motor Assembly Draw Latches 2

F25 AFS632438 6-32 x 7/16" Phillips Drive Pan Head

Screw

F26 AFT900632 6-32 Nylock Nut 4

F27 RGM250000 Cobra Motor Gasket 2

F28 ABF000500 1/2" Nylon Elbow 1

F29 RLH000006 1/4" NPT Nylon Elbow 1

F30 RLH000005 3/8" Socket 1

F31 RLH000004 3/8" Male Plug 1

F32 RLH000002 Nylon Washer 2

F33 RLH000003 Rubber O Ring 2

F34 RLH000007 Nylon Nut 1

F35 RLH000008 Round Tapered Plug 1

F36 VRV050500 1/2" ID Clear Vinyl Tubing 5 ft.

F37 RGZ190000 Cobra Gasket 1

F38 AFS015920 1/4"-20 X 3/4" Hex Head Bolt 8

F39 AFW025000 1/4" Flat Washer 16

F40 AFT000005 1/4" Whiz-Lock Nut 8

F41 AXD600300

VAB251555

9-17 Gallon Drum Liner Bag

35-55 Gallon Drum Liner Bag

If you cannot find an item on the list, examine the packaging materials very carefully.

Certain components have been pre-installed. * There may be hardware leftover.

Andere Handbücher für Dust Cobra

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems 2 HP Commercial Cyclonic Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Smart Boost... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5HP High Pressure Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-1500 1.5hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems BenchTop DC Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXS050333 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung