Rockwell Automation Allen-Bradley PowerFlex 753 Bedienungsanleitung

Release Notes

PowerFlex 753 Drives (revision 10.003)

These release notes correspond to major revision 10, minor revision 3 of

firmware for PowerFlex® 753 drives.

Introduction The following information is included in this document:

For information about: See page:

Determining Firmware Revision Level 2

Using the Drive LCD HIM 2

Using DriveExplorer Lite/Full 3

Using DriveExecutive 3

Firmware Flashing 4

Installing the Flash Kit 4

Using DriveExplorer Lite/Full to Flash Update 5

Using DriveExecutive to Flash Update 6

Using ControlFLASH to Flash Update 8

Using HyperTerminal to Flash Update 10

Enhancements 15

Corrected Anomalies 15

Known Anomalies 18

Restrictions and Compatible Revisions 19

Rockwell Automation Support 20

2Rockwell Automation Publication 750-RN034B-EN-P - November 2014

PowerFlex 753 Drives (revision 10.003)

Determining Firmware

Revision Level

This section describes procedures to determine the firmware revision of your

PowerFlex 753 drive.

Using the Drive LCD HIM

1. Access the Status screen, which is displayed on HIM power up.

Figure 1 - Status Screen

2. Use the or key to scroll to Port 00 for the Host Drive.

3. Press the key to display its last-viewed folder.

4. Use the or key to scroll to the DIAGNOSTIC folder.

5. Use the or key to select Device Version.

6. Press the (Enter) key to display device version information.

FW Revision is listed under –Main Control Board; see

Figure 2

Figure 2 - Device Version Information Screen

Stopped

0.00 Hz

AUTO

Host Drive

480V 2.1A

20F...D2P1

ESC REF TEXT

PAR#

Stopped

0.00 Hz

AUTO

ESC

PowerFlex 753

Product Revision 1.007

Product Ser Num 00000000

Product Series A

–Main Contro Board

FW Revision 5.001

TOP END P UP P DN

Rockwell Automation Publication 750-RN034B-EN-P - November 2014 3

PowerFlex 753 Drives (revision 10.003)

Using DriveExplorer Lite/Full

1. Launch DriveExplorer and go online with the PowerFlex 753 drive. To

connect to the drive, use a 1203-USB converter, a 1203-SSS converter, or

an EtherNet/IP network connection.

2. In the Devices hardware view, select the PowerFlex 753 drive.

Once selected, information regarding the PowerFlex 753 drive is shown in

the right panel including the current firmware revision number.

Using DriveExecutive

Launch DriveExecutive

and go online with the PowerFlex 753 drive. To

connect to the drive, use a 1203-USB converter, a 1203-SSS converter, or

an EtherNet/IP network connection.

2. In the Drives hardware view, select the PowerFlex 753 drive (in Figure 3

on page 4).

3. Click the information icon (in Figure 3) to display the drive’s Properties

dialog box.

In the Properties dialog box, the “Revision:” field (in Figure 3) will

show the drive’s current firmware revision number.

IMPORTANT

You need DriveExplorer version 6.02 or later to interface with the

PowerFlex 753 drive. To obtain the latest version, visit the Allen-

Bradley Web Updates site located at

http://www.ab.com/support/abdrives/webupdate.

IMPORTANT

You need DriveExecutive version 5.02 or later to interface with the

PowerFlex 753 drive. To obtain the latest version, visit the Allen-

Bradley Web Updates site located at

http://www.ab.com/support/abdrives/webupdate.

4Rockwell Automation Publication 750-RN034B-EN-P - November 2014

PowerFlex 753 Drives (revision 10.003)

Figure 3 - Accessing the PowerFlex 753 Drive Firmware Revision Number

Firmware Flashing This section describes procedures to flash upgrade your drive firmware. Flash kits

for drives are provided on the Allen-Bradley Web Updates site located at

http://www.ab.com/support/abdrives/webupdate.

Flashing can be performed using a 1203-USB or 1203-SSS converter. For

information on connecting either converter to your drive, refer to the 1203-USB

USB Converter User Manual, publication DRIVES-UM001 or the 1203-SSS

Smart Self-powered Serial Converter User Manual, publication 20COMM-

UM001.

Installing the Flash Kit

1. Install the flash kit utility from the Allen-Bradley Web Updates site for the

PowerFlex 753 drive, which includes the latest version of the

ControlFLASH utility and deploys firmware files for using

HyperTerminal on your computer.

2. You are now ready to use DriveExplorer, DriveExecutive, ControlFLASH

or HyperTerminal to update the drive. Refer to the respective section and

follow the instructions.







Rockwell Automation Publication 750-RN034B-EN-P - November 2014 5

PowerFlex 753 Drives (revision 10.003)

Using DriveExplorer Lite/Full to Flash Update

1. With the Flash Kit installed (see Installing the Flash Kit), launch

DriveExplorer and go online (via a 1203-USB or 1203-SSS converter)

with the PowerFlex 753 drive.

2. In the Drives hardware view, select the PowerFlex 753 drive (in Figure 3

on page 4).

3. Click the information icon (in Figure 3) to display the drive’s Properties

dialog box.

4. In the Properties dialog box, click the Details tab.

5. With the Main Control Board selected, click Flash Update.

IMPORTANT

Flash updating the device firmware may cause the device to load

defaults. It is recommended that you save the setting to your PC before

proceeding.

6Rockwell Automation Publication 750-RN034B-EN-P - November 2014

PowerFlex 753 Drives (revision 10.003)

From the list of available updates, select “v10.003.xxx” and click

Next >

7. Follow the remaining prompts until the flash update procedure completes

and displays the new firmware revision.

Using DriveExecutive to Flash Update

1. With the Flash Kit installed (see Installing the Flash Kit), launch

DriveExecutive and go online (via a 1203-USB or 1203-SSS converter)

with the PowerFlex 753 drive.

2. In the Drives hardware view, select the PowerFlex 753 drive (in Figure 3

on page 4).

3. Click the information icon (in Figure 3) to display the drive’s Properties

dialog box.

4. In the Properties dialog box, click the Component Details tab.

5. With the PowerFlex 753 drive selected, click Flash Update.

Rockwell Automation Publication 750-RN034B-EN-P - November 2014 7

PowerFlex 753 Drives (revision 10.003)

6. From the list of available devices, select the PowerFlex 753 drive and click

Next >.

From the list of available updates, select “v10.003.xxx” and click

Next >

8. Follow the remaining prompts until the flash update procedure completes

and displays the new firmware revision.

IMPORTANT

Flash updating the device firmware may cause the device to load

defaults. It is recommended that you save the setting to your PC before

proceeding.

8Rockwell Automation Publication 750-RN034B-EN-P - November 2014

PowerFlex 753 Drives (revision 10.003)

Using ControlFLASH to Flash Update

1. With the Flash Kit installed (see Installing the Flash Kit on page 4), launch

ControlFLASH by selecting Start > (All) Programs > Flash

Programming Tools > ControlFLASH.

2. On the ControlFLASH Welcome dialog box, click Next >.

3. The Catalog Number dialog box appears. From the list, choose the

communication device you will use to update the PowerFlex 753 drive. In

the figure below, the embedded EtherNet device is selected.

Once the appropriate communication device is selected, click Next >.

Rockwell Automation Publication 750-RN034B-EN-P - November 2014 9

PowerFlex 753 Drives (revision 10.003)

4. Now that the correct communication device has been selected, you must

select which device is being updated. With the Select the PowerFlex…

dialog box displayed, follow these steps.

a. Expand the hardware view for the communication path you are using

(in Figure 4).

b. Select the drive icon that represents the PowerFlex 753 drive you are

updating (in Figure 4).

c. Click OK (in Figure 4).

Figure 4 - Selecting the Correct Drive to Flash

5. In the Multiple Assemblies Found display box, select

“Port x-PowerFlex 753” from the list and click OK.







10 Rockwell Automation Publication 750-RN034B-EN-P - November 2014

PowerFlex 753 Drives (revision 10.003)

6. In the Firmware Revision dialog box, select “v10.003…” from the list of

available updates and click Next >.

7. Follow the remaining prompts until the flash procedure completes and

displays the new firmware revision number.

Using HyperTerminal to Flash Update

1. With the Flash Kit installed (see Installing the Flash Kit on page 4), access

and launch HyperTerminal as shown below.

IMPORTANT

The HyperTerminal process takes at least one hour to complete.

Inhaltsverzeichnis

Andere Rockwell Automation Gleichstromantrieb Handbücher

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 755 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance Electric SP200 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation RELIANCE ELECTRIC SP120 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 4M Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 400 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric 6SB401 Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 4 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Trusted TMR 24V DC Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric GV3000/SE Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Kinetix 300 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 6000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 400P Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation 6000G Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex Active Front End... Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 755TM Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 B Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance electric FlexPak 3000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DriveGuard 20D-P2-DG01 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 4M Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 700 Series Bedienungsanleitung

Beliebte Gleichstromantrieb Handbücher anderer Marken

Chamberlain Garog

Chamberlain Garog D Series Bedienungsanleitung

Parker

Parker PDS Series Bedienungsanleitung

Festo

Festo DGC G Series Einrichtungshandbuch

Binks

Binks QS-5012-1-CE Bedienungsanleitung

Danfoss

Danfoss VLT 2800 Series Technisches Datenblatt

ABB

ABB ACQ580-01 Series Installationshandbuch

YASKAWA

YASKAWA CANopen SI-S3 Bedienungsanleitung

GE D20A6 Bedienungsanleitung

Unex

Unex MC-D-250-1000-050W-TW Bedienungsanleitung

Geckodrive

Geckodrive G213V Bedienungsanleitung

ABB

ABB RSYC-01 Bedienungsanleitung

WEG

WEG DeviceNet CFW500 Bedienungsanleitung

Siemens

Siemens SINAMICS G Datenblatt

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Betriebsanleitung

SOMFY

SOMFY JR RU 30 Bedienungsanleitung

Beckhoff

Beckhoff AX8911 Bedienerhandbuch

Lenze

Lenze 8200 vector Bedienungsanleitung

Danfoss

Danfoss VLT DriveMotor FCP 106 Leitfaden