Structural Concepts FSE663R Bedienungsanleitung

REV R DATE: 04/28/2023

USER MANUALS\20-20438_OASIS_USER MANUAL_FSI(L)(H)R (ISLAND)_FSE(L)(H)R (END CAP)_CID CASE

THIS USER MANUAL IS APPLICABLE TO THE FOLLOWING MODELS:

> REFRIGERATED SELF-SERVICE ISLAND - CID MODELS FSI856R, FSI656R, FSI663R and FSI863R

> REFRIGERATED SELF-SERVICE PENINSULA END CAP - CID MODEL FSE663R

>> IMPORTANT: IF YOUR UNIT HAS AFTERMARKET PRODUCT BINS, SEE PAGE 20 OF MANUAL

FOR PLACEMENT INSTRUCTIONS.

USER

MANUAL

Model FSI663R

Model FSE663R

Model FSI656R

Model FSI863R

Oasis

READ AND SAVE THESE INSTRUCTIONS

® SCC P/N

20-20438

Structural Concepts Corp. ∙ 888 E. Porter Rd ∙ Muskegon, MI 49441 Phone: 231.798.8888 Fax: 231.798.4960 ∙ www.structuralconcepts.com

INTERNAL NOTE: ANY REVISIONS TO THIS

DOCUMENT MUST BE MADE TO P/N 20-20438

TABLE OF CONTENTS

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM ..............

CASE REMOVAL FROM SKID AND SECURE PLACEMENT IN STORE ……………………………...

REMOTE UNITS: SWIVEL CASTERS / LEVELING UNIT VIA FRAME SUPPORT RAILS OR

LEVELERS ………………………………………………………………………….. …………......….

SELF-CONTAINED UNITS: IN-LINE CASTER RAILS / LEVELERS / CONDENSER PACKAGE

CASTERS ..…………………………………………………………………………....………………..

CEILING ORIGINATED ELECTRICAL & REFRIGERATION LINES / KNOCKOUT REMOVAL /

SEALING INLET & OUTLET …..................................................................................................

REMOTE CASES: REFRIGERATION LINE FIELD CONNECTION ……….…………………….…...….

REMOTE CASES: CONDENSATE PUMP LOCATION AND PURPOSE ………………………….……

FIELD WIRING BOX / DATA COLLECTION CABLE / MAIN POWER SWITCH ..…………………....

SELF-CONTAINED UNITS: TOE-KICK ATTACHMENT INSTRUCTIONS (HORIZ. vs. VERTICAL) ..

PLAN-O-GRAM (LOAD LEVEL GUIDELINES) …………………………………....……………………….

THERMOMETERS (DIGITAL THERMOMETER & OPTIONAL “CHECK TEMPERATURE”) …..…...

POWER-UP CHECK (EVAPORATOR FAN AREA) ...……………………………………………………..

MAINTENANCE FUNDAMENTALS, CONT’D: PRODUCT BIN ATTACHMENT GUIDE ……………..

MAINTENANCE FUNDAMENTALS, CONT’D: SHELF & BRACKET ASSEMBLY REMOVAL ……...

MAINTENANCE FUNDAMENTALS, CONT’D: LED LIGHT FIXTURES / REMOVAL /

REPLACEMENT ……………………………………………………………………………………….

REFRIGERATION FUNDAMENTALS: REMOTE DRAIN LAYOUT ...…....……………...……….……..

REFRIGERATION FUNDAMENTALS: SELF-CONTAINED DRAIN LAYOUT ………………….……...

REFRIGERATION FUNDAMENTALS: CONDENSATE PACKAGE ACCESS ………………….……...

REFRIGERATION FUNDAMENTALS: CONDENSATE PACKAGE ILLUSTRATED PARTS

BREAKDOWN ………………………………………………………………………………………….

GENERAL CLEANING (TO BE PERFORMED BY STORE PERSONNEL) ……………...……………..

PREVENTIVE MAINTENANCE (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ONLY)..

TROUBLESHOOTING (TO BE PERFORMED BY STORE PERSONNEL) ……………………………..

TROUBLESHOOTING (TO BE PERFORMED BY TRAINED SERVICE PROVIDERS ONLY) ……….

TROUBLESHOOTING: CONDENSING SYSTEM (BY TRAINED SERVICE PROVIDERS ONLY) .....

TROUBLESHOOTING: EVAPORATOR SYSTEM (BY TRAINED SERVICE PROVIDERS ONLY) …

SERIAL LABEL LOCATION & INFORMATION LISTED / TECH INFO & SERVICE………………......

PROGRAMMABLE CONTROLLER INFORMATION….……………………...………………....…….......

TECHNICAL SERVICE CONTACT INFORMATION / WARRANTY INFORMATION ..…………….....

3-4

5-9

27-28

29-30

32-33

OVERVIEW

• These Structural Concepts merchandisers are

designed to merchandise packaged products at 41 °F

(5 °C) or less product temperatures.

• Cases should be installed and operated according to

this operating manual’s instructions to ensure proper

performance.

• Improper use will void warranty.

CID UNITS - TYPE 2 CONDITIONS

These units are designed for the display of products in

ambient store conditions where temperatures and

humidity are maintained within a specific range.

• These CID units are designed for Type 2 conditions.

• Type 2 conditions are ambient conditions of 60%

maximum humidity and maximum temperatures of

80 °F (27 °C).

COMPLIANCE

• Performance issues when in violation of applicable

NEC, federal, state and local electrical and plumbing

codes are not covered by warranty.

• See below compliance guideline.

WARNINGS

• This sheet contains important warnings to prevent

injury or death. Please read carefully!

REFRIGERANT DISCLOSURE STATEMENT

• This equipment is prohibited from use in California

with any refrigerants on the “List of Prohibited

Substances” for that specific end-use, in accordance

with California Code of Regulations, title 17, section

95374.

• This disclosure statement has been reviewed and

approved by Structural Concepts and Structural

Concepts attests, under penalty of perjury, that these

statements are true and accurate.

WARNING

Hazardous moving parts. Do not operate unit with covers removed.

Fan blades may be exposed when deck panel is removed.

Disconnect power before removing deck panel.

WARNING

Risk of electric shock. Disconnect power before servicing unit.

CAUTION! More than one source of electrical supply is

employed with units that have separate circuits.

Disconnect ALL ELECTRICAL SOURCES before servicing.

WARNING

ELECTRICAL

HAZARD

WARNING

KEEP

HANDS

COMPLIANCE

This equipment MUST be installed in compliance with

all applicable NEC, federal, state and local

electrical and plumbing codes.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM - PAGE 1 of 2

WARNING! POWER CORD AND PLUG MAINTENANCE

Risk of electric shock. If cord or plug becomes damaged,

replace only with cord and plug of same type.

ATTENTION

CONTRACTORS

WARNING: This product can expose you to chemicals, including

Urethane (Ethyl Carbamate), which are known to the state of

California to cause cancer and birth defects or other reproductive

harm. For more information go to P65Warnings.ca.gov.

OVERVIEW / TYPE / COMPLIANCE / WARNINGS / PRECAUTIONS / WIRING DIAGRAM - PAGE 2 of 2

CAUTION! GFCI BREAKER USE REQUIREMENT

If N.E.C. (National Electric Code) or your local code

requires GFCI (Ground Fault Circuit Interrupter) protection,

you MUST use a GFCI breaker in lieu of a GFCI receptacle.

CAUTION! LED LAMP REPLACEMENT GUIDELINES

LED lamps reflect specific size, shape and overall design.

Any replacements must meet factory specifications.

CAUTION

PRECAUTIONS

• This sheet contains important precautions to prevent

damage to unit or merchandise.

• Please read carefully!

• See previous page for specifics on OVERVIEW,

CONDITION TYPE, COMPLIANCE and WARNINGS.

WIRING DIAGRAM

• Each case has its own wiring diagram folded and in

its own packet.

• Wiring diagram placement may vary; it may be

placed near ballast box, field wiring box, raceway

cover, or other related location.

CAUTION! CHECK CONDENSATE PUMP CONNECTIONS

Water on flooring can cause extensive damage!

Carefully check the following before powering up case:

• Condensate pump must be plugged into receptacle.

• Condensate lines must be connected to condensate pump.

CAUTION! ADVERSE CONDITIONS / SPACING ISSUES

• Performance issues caused by adverse conditions are NOT warranted.

• Rear panels must be kept at least 6” from walls and structures.

• Case must not be exposed to direct sunlight or any heat source.

• To maintain proper case temperature, keep case at least 15-feet from exterior

doors, overhead HVAC vents or any air curtain disruption.

• Self-contained case clearance: 6” min. air intake / 6” min. air discharge.

CAUTION

CAUTION! DO NOT RELY ON THERMOMETERS OR THERMOSTATS

FOR ACTUAL PRODUCT (FOOD) TEMPERATURES.

• Thermometers and thermostats reflect air temperatures ONLY.

• For ACTUAL food temperatures, use a calibrated food probe.

CAUTION! CHECK CONDENSATE PAN POSITION & PLUG!

Water on flooring can cause extensive damage!

• Before powering up case, check that condensate pan is positioned

directly under case’s condensate drain.

• Before powering up case, check that condensate pan’s electrical plug is

SECURELY connected to condensate system’s receptacle.

CASE REMOVAL FROM SKID AND SECURE PLACEMENT IN STORE - PAGE 1 OF 5

4. Wood Shipping Brace Removal

• Remove all (4) wooden shipping braces. Discard.

5. Metal Shipping Bracket Removal

• Remove (1) metal shipping brackets from each end of

air intake (coil) side of case by removing (3) screws .

6. Reattach (2) Screws to The Case

• Reattach one (1) screw at each end of case (2 screws

total) to securely fasten the ‘kick brackets’ to the base

at the intake (coil) side of case.

7. Metal Shipping Bracket Reattachment

• Reattach the (2) shipping brackets to the skid (NOT

THE CASE) by reusing the (2) screws that had been

removed from each end of the skid in step #5.

• Reattaching (2) brackets to each end of the skid will

prevent case from rolling off skid during this process.

>> Important! Case Must Be Rolled Off Skid

At Exhaust Side of Case!

1. Case Received At Shipment

• Case will be shipped with lower panels attached.

2. Lower Panel Removal and Storage

• Remove ramps from skid (to use later in process).

• Remove lower panels by lifting up and off case.

• Place in area away from foot traffic.

• DO NOT REMOVE SUPPORT BRACE (at exhaust

side of case)!

3. Metal Shipping Bracket Removal

• Remove (2) metal shipping brackets

at air exhaust side of case.

Exhaust Side

Of Case

Kick

Bracket

CASE REMOVAL FROM SKID AND SECURE PLACEMENT IN STORE - PAGE 2 OF 5

12. Cardboard Ramps To Align With Casters

• Cardboard ramps are shipped with skid.

• Place cardboard ramp lip atop edge of pallet (aligned

with casters) AT EXHAUST SIDE OF CASE!

• Use tape measure for exact dimensions at TOP AND

BOTTOM OF RAMPS! Do NOT just estimate caster

to ramp alignment!

• Screw or staple each ramp in place (in at least two

locations per ramp lip). Caution! If using screws, use

flat heads so casters will not be obstructed!

• Line up ramps to casters AT EXHAUST SIDE OF

CASE (as illustrated in item #8 below)!.

>> Important! Case Must Be Rolled Off Skid At

Exhaust Side of Case!

8. View of Case After Panels & Brackets Removed

• Case is now ready to remove from skid (without

damaging panels or being secured to skid).

9. View of Caster in Locked Position

• Important! Case is shipped with casters factory set

at ON (locked) position (as shown) to help prevent

case from rolling during shipment.

10. Unlock All (4) Casters

• Unlock casters by forcefully pressing downward on

the OFF area of each caster lever.

• Lever will be parallel to floor when OFF/unlocked.

11. Use Pry Bar To Adjust Caster Positions

• Two (2) people may be required for this task.

• Press down on pry bar; rotate caster in-line.

Center Casters (One

At Each End) To

Remain On Case

During Skid Removal

10 11

Lever Will Be Parallel To Floor/

Skid When OFF/Unlocked.

Exhaust Side

Of Case

CASE REMOVAL FROM SKID AND SECURE PLACEMENT IN STORE - PAGE 3 OF 5

Exhaust Side

Of Case

Exhaust Side

Of Case

15. Carefully Slide Down Ramps to Floor

• Slowly/carefully roll case all the way down ramps to

floor.

• Make it a smooth transition from skid to floor.

>> Note: You man now discard/recycle skid,

cardboard ramps and metal shipping brackets!

16. Move Case To Desired Location

• ONE person may move case to desired location in

store.

• Due to weight of case, however, it is preferable that

TWO persons perform this task (one to move the

case while the other ‘steers’).

>> Important! Case Must Be Rolled Off Skid

At Exhaust Side of Case!

13. Slide Case To Edge of Skid/Ramps

• At least two people are required for steps 13 -15.

• Check that casters are at the center of each ramp

PRIOR TO rolling case down ramps.

• If not, remove staples/screws and adjust

accordingly.

14. Begin Rolling Case Down Ramps

• Begin rolling case down ramps.

• Important! Stop midway down ramps to check that

casters are still at center of ramps.

• If not, adjust ramps accordingly!

CASE REMOVAL FROM SKID AND SECURE PLACEMENT IN STORE - PAGE 4 OF 5

• Vertical height adjustment ring enables case to be

raised (or lowered) at each caster.

• Slotted head set screws MAY be tightened when the

desired vertical height is achieved.

• They may be loosened to adjust vertical height again.

• Vertical height adjustment ring set screws are NOT

tightened at factory.

20. Adjusting Case So It Is Level & Plumb

• Case must be in desired location before adjusting.

• Rotating vertical adjustment ring CLOCKWISE will

lower caster (raising case height).

• Use leveler on header for true level/plumb check.

• Start by adjusting caster’s vertical adjustment ring at

highest corner of case; lower it to floor.

• Then lower remaining casters until case is level and

plumb.

21, Locking ALL Casters Into Position

• To prevent case from moving after it has been moved

into position, casters must be locked.

• Lock casters after case is level and plumb.

• Press downward against the ON areas of all four (4)

caster levers with adequate force to lock them in place!

17. Remove Center Casters From Case

• Once case has been moved to desired location,

you may remove center casters.

• Just the removal of (2) horizontal screws will allow

caster to drop down and off case.

18. Caster Position at Shipment

• Case is shipped from factory with casters

RAISED to maximum height.

• This caster height aids in skid removal.

19. Caster Assembly Operation

• Image shows caster removed from case (for

illustrative purposes only).

All (4) Casters May

Now Be Locked (By

Pressing Downward

On The ON Lever).

Caster

Slotted Head Set

Screws May Be

Tightened When

Desired Vertical

Height Is Achieved)

Vertical Height

Adjustment Ring

(To Raise or

Lower Case)

CASE REMOVAL FROM SKID AND SECURE PLACEMENT IN STORE - PAGE 5 OF 5

22. Return Front and Rear Panels To Case

• Front and rear panels are to be returned case.

• Attach to case using upper hook, middle bracket

protrusion and lower magnet.

23. Return Left & Right Oval End Panels To Case

• Oval end panels are to attach to hooks, tabs and

magnets.

• They must align with front & rear end panels.

24. Adjust Left & Right Oval End Panels As Needed

• Brackets that secure oval end panels are adjustable

via obround slots.

• Loosen screws to adjust brackets (which adjusts

horizontally) to align oval end panels to front/rear

end panels so that space between panels are

WITHIN 1/4”. Then tighten screws securely.

25. View of Case - Front/Rear & End Panels Attached

• There should be NO LARGE GAPS between front/

rear panels in their alignment with oval end panels.

23 Panel Is Shown Transparent

For Viewing Slots

REMOTE UNITS: LEVELING UNIT VIA FRAME SUPPORT RAILS AND SHIMS

Model FSI656R Is Shown Above. It May Not Exactly

Reflect Every Feature or Option of Your Particular Model.

The Following Pertains To Remote Units

Leveling Unit Via Frame Support Rails

• Case must be level to assure proper operation.

• Case will have frame support rails.

• Frame support rails will need to be shimmed to

level the case.

Frame

Support Rail

Frame

Support Rail

• SCC P/N 27035 - A packet of (19) 3” x 3”

stainless steel, 18 gauge shims will be wrapped

and provided with cases with rails.

• After case has been properly shimmed, attach

panels to case (case below is shown with panels

for illustrative purposes only).

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Structural Concepts Gewerbliche Lebensmittelgeräte Handbücher

Structural Concepts

Structural Concepts REVEAL NR3633RSV Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B824TM Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts HVP48SS Montageanleitung

Structural Concepts

Structural Concepts Impulse Series Bedienungsanleitung

Structural Concepts

Structural Concepts GHSS476HRD.5718 Bedienungsanleitung

Structural Concepts

Structural Concepts Harmony HMO7536R Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Montageanleitung

Structural Concepts

Structural Concepts Impulse CSC3223 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts ENCORE Series Montageanleitung

Structural Concepts

Structural Concepts SB5735 Series Montageanleitung

Structural Concepts

Structural Concepts IMPULSE CGC2830 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts grocerant DP8HP60WD.5718B Montageanleitung

Structural Concepts

Structural Concepts HARMONY HMO2653R Bedienungsanleitung

Structural Concepts

Structural Concepts Impulse 62486 Bedienungsanleitung

Structural Concepts

Structural Concepts Reveal NR3613DSV Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis COU2757R Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis B3924RH Bedienungsanleitung

Structural Concepts

Structural Concepts Oasis BV3632 Bedienungsanleitung

Structural Concepts

Structural Concepts G Series Bedienungsanleitung

Structural Concepts

Structural Concepts Addenda CSF3931 Montageanleitung

Structural Concepts

Structural Concepts K Series Montageanleitung

Beliebte Gewerbliche Lebensmittelgeräte Handbücher anderer Marken

Blue Seal

Blue Seal EF30 Bedienungsanleitung

Tecfrigo

Tecfrigo Snelle 400 GS Bedienungsanleitung

Follett

Follett PFT Series Bedienungsanleitung

MEFE

MEFE CAT 206 PTR Leitfaden

Premier

Premier 900cl Bedienungsanleitung

Diamond

Diamond AL1TB/H2-R2 Bedienungsanleitung

Salva

Salva IVERPAN FC-18 Bedienungsanleitung

Hussmann

Hussmann Rear Roll-in Dairy Bedienungsanleitung

Cornelius

Cornelius IDC PRO 255 Bedienungsanleitung

Moduline

Moduline HSH E Series Bedienungsanleitung

MINERVA OMEGA

MINERVA OMEGA DERBY 270 Bedienungsanleitung

Cambro

Cambro IBSD37 Bedienungsanleitung

Fri-Jado

Fri-Jado LDR 8 s Bedienungsanleitung

Diamond

Diamond OPTIMA 700 Kurzanleitung

Allure

Allure Melanger JR6t Bedienungsanleitung

saro

saro FKT 935 Bedienungsanleitung

MKN

MKN OPGGSGARG Series Bedienungsanleitung

BIRO

BIRO 22 Service-Handbuch