Moxa Technologies VPort 351 Series Bedienungsanleitung

P/N: 1802003512015

Moxa Industrial Video Encoder

VPort 351 Series

Quick Installation Guide

Sixth Edition, December 2009

- 2 -

Overview

The VPort 351 is a high performance, 1-channel industrial video encoder

that provides up to full D1 (720 x 480) @ 30 FPS video performance. The

VPort 351 is designed to support multi-codecs, including MJPEG and

MPEG4 algorithms. In addition, a continuous video pre/post event-trigger

video record function is supported to enhance video surveillance systems.

The VPort 351 has many of the same industrial-grade features as other

Moxa products, including DIN-rail mounting, 24 VAC/VDC redundant

power inputs, -40 to 75°C operating temperature (“-T” models), and IP30

protection for industrial mission-critical applications. But most

importantly, the VPort 351 meets critical industrial safety standards and

approvals, such as UL508, and Class 1, Div.2, making the encoder

especially well suited for transportation, utility, and manufacturing

systems.

Package Checklist

The Moxa VPort 351 is shipped with the following items. If any of these

items are missing or damaged, please contact your customer service

representative for assistance.

•1 ×VPort 351.

•1 ×6-pin terminal block for one power input and 2 DIs.

•1 x 8-pin terminal block for the other power input and 2 Relay

Outputs.

•1 ×5-pin terminal block for RS-232/422/RS-485 PTZ control port.

•Quick Installation Guide.

•Documentation & Software CD; includes User’s Manual, Quick

Installation Guide, Moxa IVN Solution Datasheet and Utility.

•Warranty Booklet.

NOTE

Please check the model name on the VPort’s side label to verify

that the model name is correct for your order.

NOTE

This product must be installed in compliance with your local laws

and regulations.

Features

High Performance Video/ Audio Networking Solution

•Works with NTSC/PAL analog video cameras

•Supports MPEG4/MJPEG video compression technology

•1 BNC video input and 1 BNC video output with 75Ω resistance

•1 audio input and 1 audio output for 2-way voice communication

•Standard RTSP (real-time streaming protocol) for easy integration

•Multicast (IGMP) protocols for efficient network transmission

•QoS (TOS) for priority transmission

•PPPoE and DDNS for xDSL connection

•Transparent PTZ Control for controlling the PTZ camera with legacy

PTZ contorl panel or keyboard

•Built-in web server and RS-232 console for remote access &

configuration

- 3 -

•1 auto-sensing 10/100BaseT(X) Ethernet port or 100baseFX (SC

connector)

•TCP, UDP, and HTTP network transmission modes

•Allows simultaneous access of up to 10 clients

•Set video quality to CBR (constant bit rate) or VBR (variable bit rate)

•Full D1, 4CIF, VGA, QVGA, and CIF video resolution supported

•Timestamp and text overlay supported

•RS-232/RS-422/RS-485 COM port for controlling PTZ

(PAN/TILT/ZOOM) motorized camera

•DDNS (Dynamic DNS), UPnP and IP filtering supported

Industrial Rugged Design

•Two 12/24 VDC and 24 VAC redundant power inputs with LED

indicators

•-40 to 75°C operating temperature for critical industrial environments

(“-T” models)

•35 mm DIN-rail mounting or panel mounting installation (with

optional accessories)

•IP30 protection

•Class 1, Div.2 hazardous certification for critical environments

(pending)

Intelligent Alarm Trigger

•Built-in Video Motion Detection (VMD)

•Equipped with 2 DIs and 2 relays (DO) for external sensors and

alarms

•Recorded video provided for pre/post alarm

•Snapshot images provided for pre, trigger, and post alarm

•Sequential snapshot images supported

•Messages with snapshot images can be sent via FTP or Email

•HTTP Action settings for customized alarm messages being sent via

HTTP Event Server

•Configure alarm activation schedule

Video management and Control

•Moxa SoftDVRTM Lite IP Surveillance Software for viewing and

recording bundled free

•Free Moxa VPort SDK PLUS supported with flexible interface and

sample codes for customized applications or system integration

NOTE

If you are interested in the Moxa VPort SDK PLUS, please go to

Moxa’s website to download the software, or contact a Moxa sales

representative for more information.

- 4 -

VPort 351 Panel Layout

1. Grounding screw

2. RS-232 console port

3. Hardware reset button

4. 6-pin terminal block for DI 1, DI 2,

power input 2 (PWR2)

5. 8-pin terminal block for Relay 1

, Relay

2, power input 1 (PWR1)

6. Heat dissipation orifices

7. LEDs for STAT, PWR1, PWR2, FAULT

8. LEDs for VIDEO, AUDIO TEST, PTZ

9. AUDIO OUTPUT port for external

speaker

10.

AUDIO INPUT port for mic-in and line-

connection

11.

5-pin terminal block for RS-232/422/

485 connection

12.

BNC port for video input

13.

AUDIO TEST DIP switch for testing

audio input signal (default is off)

14.

75Ω DIP switch for analog video signal

transmission with 75Ω resistance

(default is on)

15.

BNC port for loop-

through video output

16.

RJ45 10/100BaseTX Ethernet P

ort with

10 Mbps, 100 Mbps LEDs

17.

100BaseFX Fiber optic port with 100

Mbps LED

18.

Model name

19.

Screw hole for wall mounting kit

20. DIN-Rail mounting kit

- 5 -

First-Time Installation and Configuration

Before installing the VPort 351 video encoder, check to make sure that all

items in the Package Checklist are in the box. In addition, you will need to

use a notebook or PC equipped with an Ethernet port.

Step 1: Select the Power Source

The VPort 351 can be powered by a DC power input from 12 to 32 VDC, or

an AC power input from 18 to 30 VAC. Two power inputs are provided for

redundancy. Users can check the LED status located on the front panel to

see if the power inputs are connected appropriately. If one of the power

inputs fails, the FAULT LED will illuminate in red.

NOTE

The VPort 351 has 2 power inputs for redundancy. Each power

input supports 12 to 32 VDC for a 12/24 VDC power input, or 18

to 30 VAC for a 24 VAC power input. This differs from Moxa’s EDS

switches, which support a 12 to 45 VDC power input.

Step 2: Connect VPort 351 to the Network

The VPort 351 has an auto-sensing 10/100 Mbps RJ45 Ethernet port, or

100 Mbps fiber optic port (multi mode or single mode) for network

connectivity. Both the RJ45 port and fiber optic port have separate LEDs

for 10 Mbps and 100 Mbps connection activity.

Step 3: Connect the VPort 351 to a camera and an audio source

The VPort 351 has a VIDEO INPUT port and a loop-through VIDEO

OUTPUT port with a 75Ω resistance dip switch. Users should use the BNC

connector and coaxial cable to connect the video camera to the VPort to

input analog video signals, and connect the monitor or DVR with the VPort

to output analog signals (note that the 75Ω resistance should be turned to

off when the video output is enabled).

The VPort 351 has 1 audio input and 1 audio output. A microphone or an

amplifier can be plugged directly into the AUDIO INPUT port; a speaker

can be plugged into the AUDIO OUTPUT port.

NOTE

A VIDEO LED is located on the front panel to indicate the video

signal transmission status for the video input. Users can check

the LED status to see if the video is working properly.

ATTENTION

A ground loop isolator

is recommended to be used between the

camera and the VPort to avoid a sudden current, which is

generated by the electric potential difference between these 2

device’s ground power, to burn out the VPort’s chips and boards.

Step 4: Connecting the VPort 351 to a motorized PTZ

camera/device

If you are using a PTZ camera or device, you need to connect the PTZ

control cable to the VPort 351’s PTZ port. The PTZ port is a 5-pin terminal

block for RS-232/422/485 serial connection. The pin assignments are

shown below.

- 6 -

PIN RS-422/485 RS-232

GND

Ground

GND

Ground

R-

Rx-

---

N/A

R+

Rx+

RxD

T-\D-

Tx-/ Data-

---

N/A

T+\D+

Tx+/ Data+

TxD

To enable PTZ control, configure the PTZ control protocol in the

web-based manager.

NOTE

The PTZ control protocol is not standardized. To use a particular

PTZ control protocol, the video server must support the driver for

that protocol. Currently, the VPort 351 supports PTZ control

protocol drivers for:

1. Pelco D

2. Pelco P

3. DynaColor DynaDome

If you need to use a protocol that is not on the list, you will need

to contact the manufacturer of the camera to get the PTZ control

commands, and then program its PTZ control in the VPort 351’s

Custom Camera function.

NOTE

The VPort 351 comes with a PTZ driver upload func

tion for

implementing new PTZ drivers. Please contact a Moxa sales

representative if you need assistance from Moxa’s R&D

department to create a new PTZ driver.

NOTE

The “Transparent PTZ Control” function in the camera driver list is

used to transmit the

PTZ control signal over a TCP/IP network to

the VPort D351 video decoder or PC (additional driver required).

The PTZ control panel or keyboard can directly control the PTZ

camera or device, eliminating the need for a PTZ camera driver

and allowing the use of PTZ cameras with the VPort encoder.

Step 5: Configure the VPort 351’s IP address

After powering on the VPort 351, wait a few seconds for the POST (Power

On Self Test) to run. The STAT LED turns green to indicate that the POST

process has completed. The IP address will be assigned when the 10 or

100 Mbps NETWORK LED blinks. The IP address assigned after the POST

is completed depends on the network environment.

Network Environment with DHCP Server

In this case, the IP address of the VPort 351 is assigned by a DHCP Server.

Use the DHCP Server’s IP address table, or use the Moxa VPort utility to

determine the IP address that was assigned by the DHCP Server.

NOTE

After powering on the VPort 351, wait a few seconds for the POST

(Power On Self Test) to run. The IP address will be assigned when

the 10 or 100 Mbps NETWORK LED blinks.

- 7 -

Using the Moxa VPort and EtherDevice Configurator Utility

(edscfgui.exe)

1. Run the edscfgui.exe program to search for VPorts and EDS

switches. After the Utility window opens, select or click on Broadcast

Search (under the List Server menu or click on Broadcast Search

icon ) to initiate a search.

NOTE

You may download the VPort and Ether Device Co

nfigurator

software from Moxa’s website at www.moxa.com.

2. The Broadcast Search window will show a list of all switches and

VPorts located on the network. The progress of the search will also

be indicated.

3. When the search has ended, the Model Name, MAC address, and IP

address of the EDS switches and VPorts will be listed in the Utility

window.

- 8 -

NOTE

Broadcast Search can only search for devices connected to the

same LAN domain as the VPort. If your devices are locate

d on

different LAN domain, use the

Specify IP Address function to

search for the device by keying in the IP address.

4. Double click the selected VPort, or use the IE web browser to access

the VPort’s web-based manager (web console).

Network Environment without DHCP Server

If your VPort 351 is connected to a network that does not have a DHCP

server, then you will need to configure the IP address manually. The

default IP address of the VPort 351 is 192.168.127.100 and the default

subnet mask is 255.255.255.0. Note that you may need to change your

computer’s IP address and subnet mask so that the computer is on the

same subnet as the VPort.

To change the IP address of VPort manually, access the VPort’s web

server, and then navigate to the System Configuration Network 

General page to configure the IP address and other network settings.

Checkmark Use fixed IP address to ensure that the IP address you

assign is not deleted each time the VPort is restarted.

Step 6: Logging in to the VPort 351 web-based manager

Type the IP address in the web browser’s address input box and then

press enter.

Step 7: Installing the ActiveX Control Plug-in

A security warning message will appear the first time you access the

VPort’s web-based manager. The message is related to installing the

VPort AcitveX Control component to your PC or notebook. Click on Yes to

install this plug-in to enable the IE web browser for viewing video images.

- 9 -

NOTE

For Windows XP SP2 or above operating systems, the ActiveX

Control component will be blocked for system security reasons.

In this case, the VPort’s security warning message window may

not appear. Users should unblock the ActiveX control function or

disable the security configuration to enable the

installation of

VPort’s ActiveX Control component.

Step 8: Accessing the Homepage of the VPort 351’s web-based

manager

After installing the ActiveX Control component, the homepage of the

VPort 351’s web-based manager will appear. Check the following items to

make sure the system was installed properly:

1. Video Images

2. Audio Sound (make sure your PC’s or notebook’s sound is turned on)

3. Video Information

Step 9: Accessing VPort’s System Configuration

Click on System Configuration to access the overview of the system

configuration to change the configuration. Model Name, Server Name,

IP Address, MAC Address, Firmware Version, and LED Status

appear in the green bar near the top of the page. Use this information to

check the system information and installation.

For details of each configuration, check the User’s Manual on the software

CD.

- 10 -

NOTE

After accessing the VPort 351’s web-based manager,

administrators should access System

Configuration



System



Account to set up the administrator’s password and enable

the authentication function. The administrator account name is

admin. An authenti

cation window will pop up requesting the

account name and password each time the VPort 351 is accessed.

Andere Handbücher für VPort 351 Series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies A50 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Handbuch

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA Handbuch

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME61 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME50-M-SC Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung