Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Rev: 12/12/2019 Doc. #ZBM000024A

Appearance may vary slightly

U.S. Patent: # #7824457,

#8377160, #8491686,

#8496719, #7937803

OWNER’S MANUAL

Mini-Gorilla

110V / 220V

# XXPM010100H

# XXPM010100H220

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 4

System Dimensions 5

System Contents 6

Assembly Instructions 8

Maintenance 14

Troubleshooting 15

FAQ 16

Recommended Accessories 18

Warranty Information 20

Notes 21

2 Oneida Air Systems

System Start-Up Information

1. Install ductwork completely before operating collector

a. Seal ductwork with silicone sealant or duct tape.

b. Have dust drum in place and sealed.

2. DO NOT operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place. Dust Drum and

Cyclone must be in place and sealed or motor will overheat!

3. DO NOT operate without lter in place. Fan blade can cause serious injury.

4. e Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! It is recommended

that at least two people li the system up.

5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated

on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or

failure to follow these directions).

6. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

7. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

8. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

9. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deagrate

(burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame

front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise

additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been

witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

Make sure to read and understand the installation and maintenance instructions as well as all

recommended safety practices.



3oneida-air.com

System Start-Up Information (Continued)

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Personnel should be kept at least 20 . away from unit.

9. Check dust bin frequently and before leaving the shop for smoldering material.

10. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

11. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

12. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

13. Empty dust bin and clean lter oen, especially when sanding.

14. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

15. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Trapped metal when drawn into the collector can spark against ductwork.

e. Check wood stock for old nails and screws which can create red hot metal fragments.

16. Avoid using excessively large wood waste bins.

17. ALWAYS check storage bins for smoldering material before leaving for the day.

18. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

19. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

20. UNPLUG UNIT BEFORE SERVICING OR CLEANING

OAS Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4 Oneida Air Systems

System Specications

OPERATION

Fan Rating (with Cyclone & Filter) 583 CFM at 2" SP (990.5 m/hr at 51 mmHO )

Maximum Suction Rating 9" HO (229mmHO)

MOTOR AND ELECTRICAL

MotorType U.S. MadeTEFC Motor

Motor Insulation Class F

Motor Service Factor 1.15

Horsepower 1.5 HP (1.1 kW)

Motor Speed 3,450 RPM

Phase Single-Phase (1ph)

Voltage 110V / 220V

Cycle 60Hz

Listed FLA 110v: 16A/ 220v: 8A

On/O Switch Rocker Switch

Power Cord 20 ft (6 m)

Power Connector 110v: NEMA 5-20 / 220v: NEMA 6-20

Recommended Circuit Size 20A

Recommended CircuitType HACR

Sound Emission 80.5 dBA @ 10 ft (3m)

IMPELLER

Size 13" (330 mm)

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter MediaType G.E. H12 HEPA

Filter Eciency 99.97% @ 0.3 microns

Filter Surface Area 40 Sq. Ft. (3.7 sq m)

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Molded Static Conductive Resin

Inlet 5" (127 mm) Outer Diameter

Overall Height 64.25" (1,632 mm)

OverallWeight 85 lbs (38.5 kg)

5oneida-air.com

Nominal dimensions shown. Dimensions subject to slight variations in manufacturing.

System Dimensions

Top View

10.5"

457 mm

28"

711 mm

43"

1,092 mm

18"

457.2 mm

24.75"

629 mm

52.25"

1,327 mm

23"

584 mm

110V 220V

e Mini-Gorilla requires a 20 Amp outlet receptacle

to be installed by a licensed electrician. See below outlet

receptacles needed based on the voltage of your unit.

64.25"

1,632 mm

6 Oneida Air Systems

System Contents

Please unpack the parts carefully and conrm you have

received each item listed here.

*Some components are pre-installed at the factory and

are listed here for your convenience.

**e U-Spring Nuts come in a pack of eight, but you will

only need six for your installation.

You will need the following:

• 7/16" Wrench

• 7/16" Socket Wrench

• 1/2" Wrench

• 1/2" Socket Wrench

• Small Hammer

• Phillips Head Screwdriver

• Flat-head Screwdriver

• Razor Blade

• Channel Lock Pliers+

ID Part number Part description Qty

A BXI001605C

BXI001604C

Motor Assembly 1.5 HP 110V

Motor Assembly 1.5 HP 220V

B FCS101935HFA

10.5" x 19.5" HEPA Cartridge

Filter with molded sound

absorber

C SXM010100C Cyclone and Drum Assembly 1

C1 SMM010100 Molded Cyclone and Drum 1

C2* AFL990001 Latches 3

C3* AFS501032 10-32 1/2" Phillips Pan Head

Screws 10

C4* AFT901032 10-32 Nylock Nut 1

C5* AFW200000 #10 Flat Washer 10

C6* RHL000604 Drum Window 1

C7* RGZ025050 Gasket 6 ft.

C8 STG491616 Leg Assembly 3

C9 AHX001605B Mini Gorilla Hardware Kit 1

C9A VAB363602 22 Gal. Heavy-Duty Plastic

Liner Bags 2

C9B VRV050500 1/2" ID Vinyl Tubing 5 ft.

C9C RGZ025050 Gasket 6 ft.

C9D ABF500000 1/2" Straight Fitting 2

C9E AFW180508 5/8" Rubber Washer 2

C9F RCP060000 PVC Tube Cap For Inlet Cover 1

C9G RHC000007 3" Casters with 5/16-18 x 1"

Stems 3

C9H AFB025175 1/4"-20 x 1 3/4" Carriage Bolt 3

ID Part number Part description Qty

C9I AFW025000 1/4" Flat Washer 3

C9J AFT000005 1/4" Whiz-Lock Nut 3

C9K AFB155195 5/16-18 x 2" Hex Head Bolt 3

C9L AFW180000 5/16" Flat Washer 3

C9M RHC000000 2" Drum Casters 3

C9N AFS015920 1/4"-20 x 3/4" Hex Head Bolt 6

C9O AFW180516 5/16" Rubber Washer 6

C9P AFW025000 1/4" Flat Washer 6

C9Q AFT000005 1/4" Whiz-Lock Nut 6

C9R** AFT051618 5/16-18" U-Spring Nut 8

C9S AFB155190 5/16-18 x 1" Hex Head Bolt 9

C9T AFW180000 5/16" Flat Washer 9

C9U ACB360000 1/2" Turn-Key Band Clamp 1

C9V RCP101935 Filter Outlet Cap 1

C9W AFW180000 5/16" Flat Washer 4

C9X AFT900006 1/4"-20 Nylock Nut 4

If you cannot find an item on the list, examine the packaging materials very carefully.

Certain components have been pre-installed.* There may be hardware leftover.



+e pliers are optional and are recommended for ease of installation.

7oneida-air.com

System Contents (Continued)

BC1

C9D C9E

C9F

C9C

C9X

C9W C8 C8 C8

C9G

C9V

C9U

C9M

C9Q

C9N C9O

C9P

C9K

C9L

C9H

C9I

C9J

C9S C9T C9R

C9B

Gasket & Bag Components

Leg Hardware

& Casters

Leg Hardware & Casters

Motor Attachment Hardware

Leg Hardware

& Casters

Filter

Attachment

Hardware

Leg Hardware & Casters

C9A

8 Oneida Air Systems

Assembly Instructions

Push three Carriage Bolts (C9H) through the

inside wall of the fan housing section of the

molded cone. read the top hole of the Legs

(C8) over the bolt and secure with a 1/4" Flat

Washer (C9I) and 1/4" Whiz-Lock Nut (C9J).

Finger tighten. [FIG. 1]

Note: e top of the leg is indicated by a hole

located 3.5" from the end. e bolt’s square shank

must go through the round housing hole. For

ease of assembly, tighten the nut on the carriage

bolt without the washer - this will pull the square

shank through the round housing hole. Once the

carriage bolt is fed through the leg's hole, remove

the nut. Secure in place with the washer and nut.

Secure each Leg (C8) to the threaded inserts on

the lid using three 5/16" Flat Washers (C9L) and

three 5/16" x 2" Hex Head Bolts (C9K). [FIG.

2a] Secure Stem Casters (C9G) to the threaded

insert on the bottom of the legs. Finger tighten.

[FIG. 2b]

Note: For ease of assembly, we recommend

channel lock pliers to tighten the casters.

FIG. 1



SECTI GG

DETAIL 

SCALE 1 : 1



SECTI GG

DETAIL 

SCALE 1 : 1

SECTI GG

DETAIL I

SCALE 1 : 1

SECTI GG

DETAIL I

SCALE 1 : 1

C9J C9I C9H

C9K C9L

FIG. 2a

C9G

C8 C8C8

C9GC9G

FIG. 2b

Andere Handbücher für Mini-Gorilla

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000014 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XSK000114 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2005c3HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Gorilla Portable XXP990201H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD002030 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 8491685 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung