Oneida Air Systems 8491685 Bedienungsanleitung

Rev: 05/17/2021 Doc. #ZBM000104

Appearance may vary slightly

U.S. Patent: #8491685,

#8496719, #7247180

OWNER’S MANUAL

High Vacuum

Dust Collector

with SMART Boost

and Air Lock

5 HP

# XXS050334

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 4

System Dimensions 5

System Contents 6

Assembly Instructions 8

Maintenance 18

Troubleshooting 19

F.A.Q. 20

Recommended Accessories 22

Warranty Information 24

Notes 25

2 Oneida Air Systems

System Start-Up Information

1. Install ductwork completely before operating collector

a. Seal ductwork with silicone sealant or duct tape.

b. Have Air Lock in place and sealed.

2. DO NOT operate Fan / Blower unless Fan Housing is attached to Cyclone body and Air Lock is in place. Air Lock and

Cyclone must be in place and sealed or motor will overheat!

3. DO NOT operate without lter in place. Fan blade can cause serious injury.

4. e Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! It is recommended

that at least two people li the system up.

5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated

on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or

failure to follow these directions).

6. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

7. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

8. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

9. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deagrate

(burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame

front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise

additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been

witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

Make sure to read and understand the installation and maintenance instructions as well as all

recommended safety practices.



3oneida-air.com

System Start-Up Information (Continued)

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Personnel should be kept at least 20 . away from unit.

9. Check dust bin frequently and before leaving the shop for smoldering material.

10. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

11. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

12. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

13. Empty dust bin and clean lter oen, especially when sanding.

14. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

15. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Trapped metal when drawn into the collector can spark against ductwork.

e. Check wood stock for old nails and screws which can create red hot metal fragments.

16. Avoid using excessively large wood waste bins.

17. ALWAYS check storage bins for smoldering material before leaving for the day.

18. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

19. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

20. UNPLUG UNIT BEFORE SERVICING OR CLEANING

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4 Oneida Air Systems

System Specications

OPERATION

Fan Rating (with Cyclone & Filter) 1,789 Actual CFM at 5.4”S.P.

Maximum Suction Rating 23”WC

MOTOR AND ELECTRICAL

Motor Type U.S. Made TEFC Motor

Motor Insulation Class F

Motor Service Factor 1.15

Horsepower 5 HP

Motor Speed 3,500-4,500 RPM

Phase Three-Phase (3ph)

Voltage 208-230V

Cycle 60Hz

Listed FLA 15A

On/O Switch Remote Starter with Push button On/O Switch and RF Keyfob

Power Cord 10 ft

Power Connector Wire

Recommended Circuit Size 30A

Recommended Circuit Size HACR

Sound Emission 84-85 dBA @ 10 ft

IMPELLER

Size 15"

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter Media Type Izumi Axtar Spunbond Media

Filter Eciency 99.9% @ 0.2-2.0 microns

Filter Surface Area 220 Sq. Ft.

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Heavy-gauge cold-rolled steel

Inlet 7" Diameter

Overall Height 143-1/2"

5oneida-air.com

143-1/2"

3,646 mm

39"

991 mm

82-3/4"

2,101 mm

30-1/2"

775 mm

39"

914 mm

106-1/4"

2,699 mm

57-1/2"

1,461 mm

203 mm

56"

1,422 mm

60-9/16”

1538 mm

Nominal dimensions shown using Height Position 3; Telescoping Stand can be adjusted to accommodate smaller

waste containers. Dimensions subject to slight variations in manufacturing.

Top View

System Dimensions

6 Oneida Air Systems

ID Part number Part description Qty

A BXI050318C Motor Assembly 5 HP 3 PH 1

B BHX020005B Fan Housing 1

C SXI002108 Barrel 1

D SCX002109 Cone 1

E DEF080099 8" Outlet Adapter 1

F FAX140033 Plenum Extension 2

G QCZ080000 8" Duct Clamp 4

H DES900899 8" Plenum Elbow 1

I DWP877099 8x7x7 Pants Wye 1

J ACB080000 6-8" Hose Clamp 4

K DHF070500 7" Diameter x 5' Flex Hose 1

L FPX020019 Dual Filter Plenum Plate 1

MAHX021819 Filter Accessory Pack 1

M1 BSC180000 Drop-in Silencer 2

M2 AFT000001 5/16"-18 Thumb Nut 16

M3 AFW180000 5/16" Flat Washer 8

M4 AFJ051602 5/16"-18 x 2" J Bolt 16

M5* AHX186200A Filter Stacking Hardware Kit 2

M6 FPZ000018 Fine Dust Bin 2

ID Part number Part description Qty

N FCS183900 18" x 39" Filter 2

O AHX001800 Hardware Kit 1

O1 RGZ025050 Poron Gasket Roll 29'

O2 AFB155155 5/16"-18 x 1" Flange Bolt 15

O3 AFW180000 5/16" Flat Washer 39

O4* AFS015700 3/8-16" x 1-1/4" Hex Head Bolt 3

O5* AFW190000 3/8" Flat Washer 20

O6* AFT000004 3/8” Whiz-Lock Nut 10

O7 AFB155190 5/16-18" x 1" Hex Head Bolt 12

O8 AFT155175 5/16-18” Whiz-Lock Nut 12

O9* AFS015100 3/8-16" x 1" Hex Head Bolt 7

O10* FGA000002 14" Grounding Cable with Two

8-18 x 3/8” Self-tapping Screws 1

P STZ210000 Stand 1

Q SAZ100000C 10" Airlock 1

If you cannot find an item on the list, examine the packaging materials very carefully. Certain

components may have been pre-installed for shipping purposes. There may be hardware

leftover.

System Contents



You will need the following tools:

GENERAL FAN HOUSING FILTER

8" Ladder Razor Knife Flathead Screwdriver 7/16" Wrench

Level Diagonal Cutters Hammer 7/16" Socket Wrench

Scissors Tape Measure / Ruler

1/2" Wrench 1/4" Socket

1/2" Socket Wrench Impact Driver

Please unpack the parts carefully and conrm you have

received each item listed here.

*Not all included parts are required for assembly.

7oneida-air.com

× 8

× 7

× 8

× 12

× 8

× 4

× 24

System Contents (Continued)

O1 Note: Comes

attached to

the Motor

Assembly (A)

8 Oneida Air Systems

Before you start, determine which direction you want your filter to hang and which direction

you want your duct work to enter the collector. The fan housing and cyclone barrel bolt holes

are drilled at 45 degree increments. Some orientations are not possible.

Assembly Instructions

Tip: Aim the dust collector's outlet away from the area where people tend to work to reduce noise.

Filter will

obstruct

inlet pipe

INLET

INCORRECTCORRECT CORRECT



FIG. 1

1 Assemble the Stand (P) [FIG 1]. Refer to the

instruction sheet included:

• Stand Instruction Sheet

# ZBI282321

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Smart Dust Collector Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems V1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Mini GORILLA XXP010101 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra - XCK010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XGK030035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Deluxe Dust Deputy Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung