Oneida Air Systems XXS050333 Bedienungsanleitung

Rev: 05/10/2021 Doc. #ZBM000104

Appearance may vary slightly

U.S. Patent: #8491685,

#8514090, #8496719,

#7247180

OWNER’S MANUAL

High Vacuum

Dust Collector

with SMART Boost

5 HP

# XXS050333

1oneida-air.com

Table of Contents

System Start-Up Information 2

System Specications 4

System Dimensions 5

System Contents 6

Assembly Instructions 8

Maintenance 20

Troubleshooting 21

F.A.Q. 22

Recommended Accessories 24

Warranty Information 26

Notes 27

2Oneida Air Systems

System Start-Up Information

1. Install ductwork completely before operating collector

a. Seal ductwork with silicone sealant or duct tape.

b. Have dust drum in place and sealed.

2. DO NOT operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place. Dust Drum and

Cyclone must be in place and sealed or motor will overheat!

3. DO NOT operate without lter in place. Fan blade can cause serious injury.

4. e Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! It is recommended

that at least two people li the system up.

5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated

on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or

failure to follow these directions).

6. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an

explosion.

7. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.

8. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.

9. To reduce the risk of injury from moving parts - unplug BEFORE servicing.

 WARNING 

 FIRE HAZARDS 

1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.

Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deagrate

(burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame

front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise

additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been

witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.

2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust

everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new

concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.

3. e following points are worth heeding:

a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction

codes and regulations when installing and operating this dust collector.

b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls

such as spark detection, suppression, or explosion venting may be required.

c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may

apply. Local codes may vary from jurisdiction to jurisdiction.

Make sure to read and understand the installation and maintenance instructions as well as all

recommended safety practices.



3oneida-air.com

System Start-Up Information (Continued)

d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking

Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust

producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).

is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult

your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.

4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application

requirements of explosion venting or if additional re protection and safety equipment may be required.

5. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!

6. NEVER collect sparks from a bench grinder into a wood dust collector.

7. NEVER introduce sparks or sources of ignition into the dust collector.

8. Personnel should be kept at least 20 . away from unit.

9. Check dust bin frequently and before leaving the shop for smoldering material.

10. Keep portable re extinguishers handy.

a. e ABC type (dry chemical) is generally a good choice for small wood shops.

b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).

11. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain

enough air volume is at the suction point to capture all the particulate generated.

12. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the

sanding dust.

13. Empty dust bin and clean lter oen, especially when sanding.

14. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.

15. Sparks can be generated in several ways:

a. High speed sanders and abrasive planers may strike foreign material.

b. Saws and edgers may strike foreign material and create a red-hot metal fragment.

c. Knots in hardwood can create frictional sparks.

d. Trapped metal when drawn into the collector can spark against ductwork.

e. Check wood stock for old nails and screws which can create red hot metal fragments.

16. Avoid using excessively large wood waste bins.

17. ALWAYS check storage bins for smoldering material before leaving for the day.

18. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)

19. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and

fuse panels which can ignite dust.)

20. UNPLUG UNIT BEFORE SERVICING OR CLEANING

Customer Service Dept.

1-866-387-8822 • support@oneida-air.com

4Oneida Air Systems

System Specications

OPERATION

Fan Rating (with Cyclone & Filter) 1,789 Actual CFM at 5.4”S.P.

Maximum Suction Rating 23”WC

MOTOR AND ELECTRICAL

Motor Type U.S. Made TEFC Motor

Motor Insulation Class F

Motor Service Factor 1.15

Horsepower 5 HP

Motor Speed 3,500-4,500 RPM

Phase Single-Phase (1ph)

Voltage 208-230V

Cycle 60Hz

Listed FLA 12-11.8A

On/O Switch Remote Starter with Push button On/O Switch and RF Keyfob

Power Cord 10 ft

Power Connector Wire

Recommended Circuit Size 30A

Recommended Circuit Size HACR

Sound Emission 84-85 dBA @ 10 ft

IMPELLER

Size 15"

Material Single-piece, backward inclined, non-sparking/non-ferrous

CARTRIDGE FILTER

Filter Media Type Izumi Axtar Spunbond Media

Filter Eciency 99.9% @ 0.2-2.0 microns

Filter Surface Area 220 Sq. Ft.

SYSTEM DIMENSIONS AND CONSTRUCTION

Barrel/Cyclone Body Heavy-gauge cold-rolled steel

Inlet 7" Diameter

Overall Height (with 55 Gallon Drum) 106"

5oneida-air.com

106"

2,692 mm

18"

457 mm

48"

219 mm

87-1/2"

2,223 mm

30"

762 mm

36"

914 mm

68"

1,727 mm

78-1/2"

1,994 mm

37"

940 mm

203 mm

27"

686 mm

30”

762 mm

Nominal dimensions shown with a 55 gallon drum. Dimensions subject to slight variations in manufacturing.

Top View

System Dimensions

6Oneida Air Systems

Please unpack the parts carefully and conrm you have

received each item listed here.

*Additional parts are included in your hardware

package.

ID Part number Part description Qty

A BXI050318C Motor Assembly 5 HP 3 PH 1

B BHX020005B Fan Housing 1

C SXI002108 Barrel 1

D SCX002109 Cone 1

E ACB120000 8-12" Hose Clamp 2

F DHF090001 9" x 1' Diameter Flex Hose 1

G SEX550900 Steel Drum Lid w/ 9" Collar 1

H SES550000 55 Gallon Steel Drum w/ Clamp 1

I DEF080099 8" Outlet Adapter 1

J DES900899 8" Plenum Elbow 1

K DWP877099 8x7x7 Pants Wye 1

L ACB080000 6-8" Hose Clamp 4

M DHF070000 7" Diameter Flex Hose 3'

N FPX020019 Dual Filter Plenum Plate 1

O AHX0021819 Filter Accessory Pack 1

O1 BSC180000 Drop-in Silencer 2

O2 AFT000001 5/16"-18 Thumb Nut 16

O3 AFW180000 5/16" Flat Washer 8

O4 AFJ051602 5/16"-18 x 2" J Bolt 16

O5* AHX186200A Filter Stacking Hardware Kit 2

O6 FPZ000018 Fine Dust Bin 2

O7 FPB210001 Dual Filter Adapter Bracket 2

O7A AFB155175 5/16-18" x 3/4" Hex Head Bolt 3

O7B AFW180000 5/16" Flat Washer 3

ID Part number Part description Qty

O7C AFT155175 5/16 Whiz Lock Nut 3

P FCS183900 18" x 39" Filter 2

Q AHX001800 Hardware Kit 1

Q1 RGZ025050 Poron Gasket Roll 29'

Q2 QCZ080000 8" Duct Clamp 2

Q3 AFB155155 5/16"-18 x 1" Flange Bolt 15

Q4 AFW180000 5/16" Flat Washer 39

Q5* AFS015700 3/8-16" x 1-1/4" Hex Head Bolt 3

Q6* AFW190000 3/8" Flat Washer 20

Q7* AFT000004 3/8” Whiz-Lock Nut 10

Q8 AFB155190 5/16-18" x 1" Hex Head Bolt 12

Q9 AFT155175 5/16-18” Whiz-Lock Nut 12

Q10* AFS015100 3/8-16" x 1" Hex Head Bolt 7

Q11 FGA000002 14" Grounding Cable with Two

8-18 x 3/8” Self-tapping Screws 1

R STZ212300 Stand 1

S STZ212301 Stand Extensions 1

T AXB999110B Dust Sentry 1

If you cannot find an item on the list examine the packaging materials very carefully. Certain

components may have been pre-installed for shipping purposes. There may be hardware

leftover.

System Contents



You will need the following tools:

GENERAL FAN HOUSING FILTER

8' Ladder Razor Knife Flathead Screwdriver 7/16" Wrench

Level Diagonal Cutters Hammer 7/16" Socket Wrench

Scissors Tape Measure / Ruler

1/2" Wrench 1/4" Socket

1/2" Socket Wrench Impact Driver

7oneida-air.com

× 8

× 7

× 8

× 6

× 12

× 8

× 4

× 24

System Contents (Continued)

Q11

O7A

O7B

O7C

Q10

Q1 Note: Sent

out attached

to the Motor

Assembly (A)

8Oneida Air Systems

Before you start, determine which direction you want your filter to hang and which direction

you want your duct work to enter the collector. The fan housing and cyclone barrel bolt holes

are drilled at 45 degree increments; Some orientations are not possible.

Assembly Instructions

Tip: e collector will seem quieter if the outlet is aimed away from the area where people tend to work.

Filter will

obstruct

inlet pipe

INLET

INCORRECTCORRECT CORRECT



FIG. 1

1 Assemble the Stand (R) and Stand Extensions

(S) [FIG 1]. Refer to the instruction sheets

included:

• Stand Instruction Sheet

# ZBI000014

• Leg Extension Instruction Sheet

# ZBI000013

Inhaltsverzeichnis

Andere Oneida Air Systems Staubabscheider Handbücher

Oneida Air Systems

Oneida Air Systems V - 2000 2hp Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Vortex DCS Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 2000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Cobra Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM010000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 3H Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell Mobile Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 5 & 7.5 HP Direct Drive Cyclonic Dust... Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XGK030035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 8491685 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 10 HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems 2005c3HP Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Pro 1500 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XCKM013000 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD990003 Bedienungsanleitung

Oneida Air Systems

Oneida Air Systems XXK050100 Bedienungsanleitung

Beliebte Staubabscheider Handbücher anderer Marken

Fein

Fein 9-88-35 Bedienungsanleitung

Blastrac

Blastrac BDC-44 Bedienungsanleitung

DIVERSITECH

DIVERSITECH WB-4000-D Handbuch

National

National 3402 Bedienungsanleitung

Grizzly

Grizzly G0850 Bedienungsanleitung

Bosch

Bosch GDE18V-16 Montageanleitung

Grizzly

Grizzly G0441HEP Bedienungsanleitung

Storch

Storch Cover Quick Wall Bedienungsanleitung

laguna

laguna C FLUX 1 Bedienungsanleitung

GMC

GMC RDC8LA Bedienungsanleitung

Jet

Jet DC-1100VX Series Service-Handbuch

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Bedienungsanleitung

King Industrial

King Industrial KC-4043KWRC Bedienungsanleitung

Jet

Jet 500 Bedienungsanleitung

Shop fox

Shop fox SHOP FOX W1687 Bedienungsanleitung

Blastrac

Blastrac 655DC Bedienungsanleitung

Elektra Beckum

Elektra Beckum Multi 180A Bedienungsanleitung

Grizzly

Grizzly G0508 Kurzanleitung