CrimeStopper CS-9701 Gargoyle Bedienungsanleitung

CRIMESTOPPER SECURITY PRODUCTS CS-9701

Wiring

Main Harness: 10 pin 18 gauge wires

Red Wire: +12Volt Power

Connect to constant +12volt power source with supplied in line 10 amp fuse and fuse holder.

Black Wire: Chassis Ground

Connect to body metal of the vehicle using a sheet metal screw.

Yellow Wire: Ignition Switched "ON" and "START" +12Volts

Connect to an Ignition Wire (or fuse in the fuse box) that shows +12Volts when the key is in both the

"ON" and "START" positions.

Orange Wire: (-) Negative Starter Disable Output (optional)

This wire is connected to terminal 85 of a relay for the starter disable. Connect terminal 86 to the Yellow

ignition switched wire. Cut the vehicle starter wire. Connect one half to terminal 30 and the other half to

terminal 87a.

White Wire: +12Volts Flashing Parking Light Output (optional)

Connect to any parking light or to the parking light output at the back of the headlight switch. ! ! ! DO

NOT CONNECT TO DASH DIMMER CIRCUIT ! ! !

Brown Wire: + Siren Output

Connect brown wire to siren red wire. Connect black wire of siren to chassis ground (body metal).

Blue Wire: (-) Hood/Trunk Pin Switch Input

Connect to pin switches which go to ground when hood and trunk are opened. It may be necessary to

install your own switches.

Green Wire: (-) Door Pin Switch Input

Connect to door switches which go to ground when door is opened. A (-) negative door switch wire will

read +12 volts when doors are closed.

Violet Wire: (+) Door Pin Switch Input

Connect to door switches which go to +12 volts when door is opened. A (+) positive door switch wire will

read (-) ground when doors are closed.

Gray Wire: (-) Negative Remote Output (optional, requires relay)

Connect to terminal 85 of relay. Connect terminal 86 to +12Volts constant. Connect terminal 87 to

+12volt constant or (-) ground. Connect terminal 30 to device to be activated.

Sensor Plug: 4 Pin 22 Gauge

White Wire -Negative Warn Away

Blue Wire -Negative Trigger

Black Wire -Sensor Ground

Red Wire -Sensor +12Volt Power

The sensor supplied with this system requires no additional wiring. Simply mount the sensor in a suitable

location and plug it in. Adjust sensitivity as necessary.

LED and Override/Valet Switch Plug: 2 Pin 22 Gauge

Connect LED plug to Red Connector on module and connect Override/Valet plug to Blue connector on

module.

Power Door Locks: 3 Pin 22 Gauge (optional)

Blue Wire (-) Negative Door Unlock Output

Connect to factory unlock relay or to relay to activate motors.

Green Wire: (-) Negative Door Lock Output

Connect ot factory lock relay or to relay to activate motors.

Red Wire (+) +12Volts Constant

Connect to terminal 86 of after market relay for activating positive, reverse polarity and after market door

locking systems. DO NOT USE THIS RED WIRE FOR MAIN POWER TO ACTIVATE DOOR LOCK

MOTORS.

Programming Dip Switches

There are 4 dip switches under the access door of the control module for pre installation programming.

Dip Switch #1: Door Lock/Unlock Pulse Time

ON: Pulse time = .75 seconds

OFF: Pulse Time = 3 seconds

Dip Switch #2: Ignition Controlled Lock/Unlock

ON: Lock/Unlock with ignition

OFF: "NO" Lock/Unlock with ignition

Dip Switch #3: Passive Arming Locks

ON: Doors lock when system arms passively

OFF: Doors do not lock when system arms passively

Dip Switch #4: Passive / Active Arming Select

ON: Alarm arms automatically 30 seconds after last door is closed (PASSIVE)

OFF: Alarms arms only with remote control (ACTIVE)

Transmitter Programming

This system uses code learning to learn up to 3 different transmitter codes. Follow these 4 simple steps

to program a transmitter to your system.

1. Turn ignition switch on -off -on -off -on. Siren will chirp once.

2. Push the Valet/Override switch for 5 seconds until the siren chirps 3 times. Release the Valet Switch.

3. Press the Large Button or button #1 of the transmitter -The Siren will chirp to confirm programming.

Repeat this procedure within 5 seconds for up to 2 additional transmitters.

4. Turn off ignition.

Note 1: If only one transmitter is being programmed, continue holding button #1 until dash LED flashes 4

times. This means the system has exited program mode. Holding the transmitter button until the LED

flashes prevents unauthorized code and noise from entering the system.

Note 2: Program mode is exited automatically after 5 seconds of last code transmission or once three

new codes have been programmed. LED will flash 4 times indicating program mode has terminated.

OWNERS INSTRUCTIONS:

Active Arming Mode:

Press button #1 once momentarily. Alarm arms and confirms with:

1 Siren Chirp

Lights flash once

LED lights solid then starts flashing slowly

Power locks will lock (if equipped)

Starter circuit enabled (optional)

Disarming:

Press button #1 once momentarily. Alarm disarms and confirms with:

2 Siren Chirps

Lights flash twice

LED stops flashing (turns off)

Power locks will Unlock (if equipped)

Starter circuit disabled (optional)

Silent Active Arming/Disarming Mode:

To Activate, turn ignition on, within 10 seconds press button #2 for 3 seconds.

Siren will emit a double chirp -Silent Arm/Disarm mode is on. System will operate without siren chirps.

Alarm will remain chirp less until Silent Mode is deactivated.

To De-Activate, turn ignition on, within 10 seconds press button #2 for 3 seconds.

Siren will emit 2 double chirps -Silent Arm/Disarm mode is off. System will operate with siren chirps.

Passive Arming Mode: Optional

Must be programmed -Consult your installer.

When exiting the vehicle, upon closing the last door there will be a 30 second delay before arming. The

LED will be flashing rapidly indicating the system is in passive arming mode. After the delay, the system

will arm and confirm with:

1 Siren Chirp

Lights flash once

LED starts flashing slowly

Power locks will lock (if equipped & dip switch # is ON)

Starter circuit enabled (optional)

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper Fortress FS-10 Handbuch

CrimeStopper

CrimeStopper CM-2500 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9703 Handbuch

CrimeStopper

CrimeStopper CS-2011RS.III Bedienungsanleitung

CrimeStopper

CrimeStopper HP-8710 Kurzanleitung

CrimeStopper

CrimeStopper CS-2000DPII SERIES IV Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9600 Technisches Datenblatt

CrimeStopper

CrimeStopper Super Page V CS-2014TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4011 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2007 Systemhandbuch

CrimeStopper

CrimeStopper CS-882 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2015.FM.RevB Bedienungsanleitung

CrimeStopper

CrimeStopper CS-882 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper RS-300 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2100 Handbuch

CrimeStopper

CrimeStopper CS-2011RS Series III Super Rage Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2000DPII TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9602PI Betriebsanleitung

CrimeStopper

CrimeStopper Fortress FS-30 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2005.FM Montageanleitung

CrimeStopper

CrimeStopper The Informer II CS-2016FM Bedienungsanleitung

CrimeStopper

CrimeStopper Traknet TN-4008 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2000 Handbuch

CrimeStopper

CrimeStopper CS-2004 WDC Bedienungsanleitung

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung